Mikrotik CRS317-1G-16S+RM Bedienungsanleitung

Mikrotik Schalter CRS317-1G-16S+RM

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Mikrotik CRS317-1G-16S+RM (6 Seiten) in der Kategorie Schalter. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/6

CRS317-1G-16S+RM

The CRS317 is a network switch with sixteen SFP+ cages (modules are not included) for high-performance 10GbE

connectivity (1.25Gbit modules are also supported) and a 1GbE copper port for management. The device is ready

to use as a switch.

Quick start

•Mount unit in a rackmount cabinet or place on the flat surface (see “ ”).Mounting

•Connect two powering units to the AC source using power cords.

•The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility.

•Use Winbox to connect to the default IP address of 192.168.88.1 from any port, with the username admin

and no password.

•We recommend clicking the “Check for updates” button and updating your RouterOS software to the latest

version to ensure the best performance and stability.

•Set up your password to secure the device.

Mounting

The device is designed to use indoors and it can be mounted in a rackmount enclosure using provided rack

mounts, or it can be placed on the desktop. Please attach rubber pegs on the bottom of the router if the desired

placement is on the flat surface or use a Phillips screwdriver to attach rackmount ears on both sides of the device if

designated use is for rackmount enclosure:

1. Attach rack ears to both sides of the device and tighten four screws to secure them in place, as shown in

the picture.

2. Place the device in the rackmount enclosure and align with the holes so that the device fits conveniently.

3. Tighten screws to secure it in place.

The IP rating scale for this device is IP0. The device has no protection from water contamination, please

ensure the placement of the device in a dry and ventilated environment.

We recommend Cat6 cables for our devices.

Mounting and configuration of this device should be done by a qualified person.

Powering

The device accepts powering through two IEC C14 standard connectors and supports both AC 110/220 V ⏦. Only

one PSU is active at the time, the second one is used for redundancy.

PoE injector is not included. The power consumption of this device under maximum load is up to 44W.

See mikrotik.com/products for the latest version of this document. Page 1, Document #51554 Modified on: 22.AUG.2019

Booting process

The device supports booting RouterOS (for complete routing and switching configuration) or SwOS (for only using

as a switch). By default, the device will boot RouterOS, but you can reboot into the other operating system in the

following ways:

•From SwOS: In the System menu, click “Boot RouterOS” button on the bottom of the page.

•From RouterOS: in the System, RouterBOARD menu, click “Settings” and there select “Boot OS”.

The device is fitted with passive cooling heatsinks and under normal load will operate silently, but in emergencies,

two redundant fans will automatically switch on to keep the device cool, if ambient temperatures are above normal.

The device has been tested to operate in ambient temperatures from -40 ℃ to +70 ℃.

Configuration

Full RouterOS and SwOS documentation are located here: .http://mt.lv/help

This device is not preconfigured other than an IP address on the master Ethernet port. You can connect from any

port, as all ports are switched together by default. Another configuration has to be applied according to the

documentation manual linked above.

The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility. Winbox should be

used to connect to the default IP address of 192.168.88.1 from any port, with the username admin and no

password.

In case the IP connection is not available, the Winbox tool ( ) can also be used to connect to thehttp://mt.lv/winbox

MAC address of the device. Applies only when the device has booted RouterOS.

The device is equipped with an RJ45 serial port, set by default to 115200bit/s, 8 data bits, 1 stop bit, no parity.

Standard RJ45 to COM cable can be used, pinout can be found in the documentation.

Extension slots and ports

•One gigabit Ethernet ports for management (With Auto MDI/X so you can use either straight or cross-over

cables for connecting to other network devices). The Ethernet port (ETH/BOOT) can be used for network

booting.

•16 SFP+ cages, which accept both 1.25 Gb SFP and 10 Gb SFP+ modules.

•RJ45 serial port.

Reset button

The RouterBOOT reset button has the following functions. Press the button and apply the power, then:

•Release the button when a green LED starts flashing, to reset RouterOS configuration to defaults.

•Release the button when the LED turns solid green to clear all configuration and defaults.

•Release the button after LED is no longer lit (~20 seconds) to cause a device to look for Netinstall servers

(required for reinstalling RouterOS over the network).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed

before power is applied to the device. Useful for RouterBOOT debugging and recovery.

Accessories

Package includes the following accessories that come with the device:

•EU/US Power cord.

•1U rackmount bracket white.

•Fastening set for rackmount case K-10 R2.

Please visit wiki pages for MikroTik SFP module compatibility table:

https://wiki.mikrotik.com/wiki/MikroTik_SFP_module_compatibility_table

See mikrotik.com/products for the latest version of this document. Page 2, Document #51554 Modified on: 22.AUG.2019

Specifications

For more information about this product, specification and pictures please visit our web page:

https://mikrotik.com/product/crs317_1g_16s_rm

Operating system support

The device supports dual boot SwOS software version 2.9 and RouterOS v6. The specific factory-installed version

number is indicated in the RouterOS menu /system resource. Other operating systems have not been tested.

https://wiki.mikrotik.com/wiki/SwOS

Safety Notice

Electric shock hazard. This equipment is to be serviced by trained personnel only.

MikroTik mobile app

Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for

your MikroTik home access point. Scan QR code and choose your preferred OS.

See mikrotik.com/products for the latest version of this document. Page 3, Document #51554 Modified on: 22.AUG.2019

Produktspezifikationen

Marke:	Mikrotik
Kategorie:	Schalter
Modell:	CRS317-1G-16S+RM
Prozessortaktfrequenz:	800 MHz
Breite:	443 mm
Tiefe:	224 mm
Mitgelieferte Kabel:	AC
Produktfarbe:	Grau
Höhe:	44 mm
AC Eingangsspannung:	110 - 240 V
Betriebstemperatur:	-20 - 60 °C
Netzstandard:	IEEE 802.1Q
Unterstützte Sicherheitsalgorithmen:	SNMPv2,SNMPv3
Power over Ethernet (PoE):	Nein
Warentarifnummer (HS):	85176990
Stromverbrauch (max.):	42 W
LED-Anzeigen:	Ja
Switch-Typ:	Managed
Basic Switching RJ-45 Ethernet Ports-Typ:	Keine
Konsolen-Port:	RJ-45
Netzstecker:	DC-Anschluss
10G-Unterstützung:	Ja
MAC-Adressentabelle:	- Eintragungen
Routing-/Switching-Kapazität:	- Gbit/s
Rack-Einbau:	Ja
Benutzerhandbuch:	Ja
Formfaktor:	1U
Web-basiertes Management:	Ja
Anzahl Gigabit Ethernet (Kupfer) Anschlüsse:	1
Port-Spiegelung:	Ja
Link Aggregation:	Ja
Spannbaum-Protokoll:	Ja
VLAN-Unterstützung:	Ja
Anzahl der VLANs:	4000
Speicherkapazität:	16 MB
RAM-Speicher:	16 MB
Reset-Knopf:	Ja
Montageblöcke enthalten:	Ja
Eingebauter Prozessor:	Ja
Flash-Speicher:	1000 MB
Broadcast-Sturmkontrolle:	Ja
Switch-Ebene:	L3
Anzahl Lüfter:	2 Lüfter
Anzahl von Stromversorgungseinheiten:	2
Speichertyp:	Flash
Menge Modul-Steckplätze SFP+:	16