Microchip SY89851U Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Microchip SY89851U (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
Low Power, 3GHz, 1:2 LVPECL
Fanout Buffer/Translator with Internal
Termination
SY89851U Evaluation Board
June 2005
M9999-062905
hbwhelp@micrel.com or (408) 955-1690
General Description
The SY89851U evaluation board is designed for
convenient setup and quick evaluation of the device.
The board is optimized to interface directly to 50Ω
system.
The default evaluation board is configured with AC-
coupled inputs and outputs. For applications that
require DC-coupled outputs, instructions for modifying
the board are included.
Data sheets and support documentation can be found
on Micrel’s web site at: www.micrel.com.
Features
• SY89851U
• Single +2.5V or +3.3V power supply
• AC-coupled inputs and outputs
• Evaluation board re-configurable for DC-coupled
outputs
Related Documentation
• SY89851U, Low Power, 3GHz 1:2 LVPECL
Fanout Buffer/Translator with Internal Termination
Data Sheet
____________________________________________________________________________________
Evaluation Board
Micrel, Inc.
SY89851U Evaluation Board
June 2005
M9999-062905
hbwhelp@micrel.com or (408) 955-1690
2
Evaluation Board Description
AC-Coupled Evaluation Board
The SY89851U evaluation board is designed to
operate with a single 2.5V ±5% or 3.3V ±10% power
supply and is configured with AC-coupled inputs and
outputs.
The high-speed input channels are brought out to
SMA connectors through matched length AC-coupled
differential strip-line traces. The inputs DC-operating
point is set at V
CC
–1.3V by the V
REF-AC
output pin,
which is connected to the V
T
input of the device.
The outputs are brought out to SMA connectors
through matched length AC-coupled differential strip-
line traces, which allow the board to interface with
50Ω system.
Although the evaluation board is configured in AC-
coupled mode, the outputs can be reconfigured in
DC-coupled mode.
AC-Coupled Input
It is recommended that the inputs are left in AC-
coupled mode. In this mode, signals automatically
bias to V
CC
-1.3V since V
REF-AC
is connected to the V
T
input. Therefore, the inputs can be driven by a
differential signal as small as 100mV (200mV
pp
).
DC-Coupled Evaluation Board
The SY89851U evaluation board can be configured in
DC-coupled output mode by removing capacitors C8-
C11 and replacing the components with 0Ω resistors.
Unused outputs
• Single-ended to scope
Unused complimentary outputs should be
terminated to 50Ω-to-ground.
• Unused output pairs
Unused pairs can be left floating with no
impact on jitter.
Evaluation Board Layout
PC Board Layout
The evaluation board is constructed with Rogers 4003
material, is coplanar in design, fabricated to minimize
noise, achieve high bandwidth and minimize
crosstalk.
Layer SY89851U
L1 GND and Signal
L2 GND
L3 V
CC
and V
EE
L4 GND
Table 1. Layer Stack
Micrel, Inc.
SY89851U Evaluation Board
June 2005
M9999-062905
hbwhelp@micrel.com or (408) 955-1690
3
Evaluation Board
Supply Voltage I/O V
CC
GND V
EE
C8-C11 R1-R4
2.5V/3.3V AC-Coupled Input/AC-Coupled Output
(1)
2.5/3.3V 0 0 0.1µF 82Ω
2.5V AC-Coupled Input/DC-Coupled Output
(2)
2V 0 –0.5V 0Ω N/A
3.3V AC-Coupled Input/DC-Coupled Output
(2)
2V 0 –1.3V 0Ω N/A
Table 2. SY89851U Evaluation Board Setup
Notes:
1. Default setting.
2. Remove capacitors at C8-C11 and replace with 0Ω resistors.


Produktspezifikationen

Marke: Microchip
Kategorie: Nicht kategorisiert
Modell: SY89851U

Brauchst du Hilfe?

Wenn Sie Hilfe mit Microchip SY89851U benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Microchip

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-