Microchip MIC2786 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Microchip MIC2786 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
MIC2786/7/8/9 Evaluation Board
Push-Button Reset IC
MLF and MicroLeadFrame are trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
May 2012 M9999-052412
General Description
The MIC2786/7/8/9 are low-current, ultra-small, push-
button reset supervisors with long set-up delays. All the
devices feature two manual reset inputs and two reset
outputs. The devices initiate a reset for the reset timeout
period when the /MR0 and /MR1 inputs are asserted low
for a period longer than the set-up delay.
In addition, the MIC2786 and MIC2787 feature an
integrated supply voltage monitor. Reset will be
asserted for the reset timeout delay once the supply
voltage increases above the rising threshold voltage.
The MIC2786 and MIC2788 feature integrated pull-up
resistors on the /MR0 and /MR1 inputs, while the
MIC2787 and MIC2789 require external pull-up
resistors. The PDY input pin selects between a 2s, 4s,
or 6s set-up period. Factory-programmed reset timeout
periods of 140ms (minimum) and 240ms (minimum) are
available.
The MIC2788-XYMT EV Evaluation Board comes with
the MIC2788-XYMT (tRESET = 140ms) installed, but it can
also be used to evaluate the MIC2786, MIC2787 and
MIC2789. Contact Micrel or an authorized distributor for
samples and simply replace the chip on board, as these
devices are all pin-to-pin compatible.
For the MIC2787 and MIC2789, positions R1 and R2 will
need to be populated with 100kΩ resistors.
Datasheets and support documentation can be found on
Micrel’s web site at: www.micrel.com.
Requirements
The MIC2788 Evaluation Board requires only a single
power supply that is capable of delivering greater than
1mA at a voltage range of 1.5V to 5.5V. An oscilloscope
can be used to view and measure the inputs and
outputs.
Precautions
There is no reverse input protection on this board. While
connecting supplies and signals ensure that correct
polarities are observed. The maximum operating VIN is
rated at 5.5V.
Getting Started
1. VIN Supplies
Connect a supply to the VIN and GND terminals, paying
careful attention to the polarity and the supply range
(1.5V ≤ VIN ≤ 5.5V). An ammeter may be placed
between the input supply and the VIN terminal to the
evaluation board. Ensure that the supply voltage is
monitored at the VIN terminal. The ammeter can reduce
the voltage supplied to the input.
2. Connect PDY Pin (J5)
Connect the programmable delay input (PDY) pin
according to desired set-up delay. Leave PDY pin open
for setup-delay of 2s, connect to GND for set-up delay of
4s or connect to VIN for set-up delay of 6s.
3. Monitor Inputs and Outputs
Monitor the inputs (/MR0 and /MR1) and outputs (/RST
and RSTP) with an oscilloscope.
4. Turn on the Power
Turn on the power supply. Observe that /MR0, /MR1
and /RST are pulled up to VIN while RSTP remains at
0V.
5. Press Push-Buttons
Press push-button inputs /MR0 and /MR1 and observe
/RST and RSTP outputs. Keeping the push-button
inputs asserted low for the programmed setup delay
time initiates one reset output pulse for the reset timeout
delay period.
Ordering Information
Part Number Description
MIC2788-XYMT EV MIC2788 Evaluation Board
Micrel, Inc. MIC2786/7/8/9 Evaluation Board
May 2012 2 M9999-052412
Evaluation Board Features
See the MIC2788/MIC2789 datasheet for detailed
explanations of these functions. For detailed operation
of the MIC2786/MIC2787 see the MIC2786/MIC2787
datasheet.
Programmable Delay Pin (PDY)
Use Table 1 to program the PDY pin for desired set-
up delay time.
PDY Configuration (J5) tSETUP
OPEN 2s
GND 4s
VIN 6s
Table 1. PDY Configuration for Desired Set-Up Delay
Figures 1, 2 and 3 illustrate manual reset function for
set-up delays as per PDY pin connection.
Figure 1. Manual Reset Function for 2.0s Set-Up Delay
(PDY = OPEN)
Figure 2. Manual Reset Function for 4.0s Set-Up Delay
(PDY = GND)
Figure 3. Manual Reset Function for 6.0s Set-Up Delay
(PDY = VIN)
Dual Manual Reset Inputs (/MR0, /MR1)
The manual reset inputs can be operated manually
using the push-buttons provided or by connecting a
function generator. Test points J1 – J4 are provided
on the manual reset inputs for connecting to a function
generator and monitoring on an oscilloscope
simultaneously.
Reset Outputs (/RST, RSTP)
The /RST output has a 100kΩ pull-up resistor to VIN.
Test-point J7 is provided for monitoring the /RST
signal on an oscilloscope. The RSTP output can be
monitored directly by an oscilloscope connected to the
test-point J6.
Micrel, Inc. MIC2786/7/8/9 Evaluation Board
May 2012 3 M9999-052412
Evaluation Board Schematic
Bill of Materials
Item Part Number Manufacturer Description Qty.
C1 GRM188R71C104KA01D Murata(1) 0.1µF, 16V capacitor, X7R, 0603 1
R4 CRCW0603100KJNEA Vishay(2) 100k, 5% resistor, 0603 1
R1, R2 DNP 0
U1 MIC2788-XYMT Micrel, Inc.(3) Push-Button Reset IC 1
Notes:
1. Murata: www.murata.com.
2. Vishay: www.vishay.com
.
3. :: Micrel, Inc www.micrel.com.


Produktspezifikationen

Marke: Microchip
Kategorie: Nicht kategorisiert
Modell: MIC2786

Brauchst du Hilfe?

Wenn Sie Hilfe mit Microchip MIC2786 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Microchip

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-