Microchip HV892DB1 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Microchip HV892DB1 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Supertex inc.
Supertex inc.
www.supertex.com
HV892DB1
Doc.# DSDB-HV892DB1
B032114
General Description
The HV892DB1 liquid lens driver demoboard is controlled via
an I2C interface, is capable of driving capacitive loads of up to
200pF, and is compatible with 40VRMS to 60VRMS lenses.
A charge pump boost converter integrated on-chip provides
the high voltage necessary for driving the lens. No external
inductors or diodes are needed. The board requires only two
ceramic chip capacitors to complete a lens driver circuit.
An H-bridge output stage provides AC drive to the lens,
allowing the use of a single high voltage boost converter while
providing alternating polarity to the lens. Controlled rising and
falling edges on the drive waveform reduces EMI.
Board Layout and Connections
Inductorless,
Liquid Lens Driver Demoboard
Speciîšżcations
Parameter Value
Supply voltage (VIN) 2.65 – 5.50V:
Supply current (IIN
):20mA max operating
500nA max standby
Output voltage (OUT1 – OUT2):9.8 – 62.6VRMS,
adjustable via I2C
Load (lens) capacitance 100 – 200pF:
I2C reference voltage (VDD) 1.70 – 2.95V:
I2C clock: 400kHz max
I2C address (7-bit): 0100011b
Board dimensions: 35.6mm x 26.2mm
Connections:
VIN
Supply voltage to the HV892. Externally supplied VIN should
be between 2.65 and 5.50V.
GND
Circuit common.
VDD
Externally supplied logic reference voltage for the I2C inter-
face. VDD should be between 1.70 and 2.95V.
SCL
I2C clock. Clock frequency should be no greater than
400kHz.
SDA
I2C data.
OUT1 OUT2 and
The lens driver output. Connect the lens between these two
terminals. Load (lens) capacitance should be between 100
and 200pF, including any stray capacitance.
Note:
The resistors shown in the connection diagram are the
normal I2C pull-ups. No additional pull-ups are required.
IC1
CIN CHV
Liquid Lens
100 - 200pF
VIN =
2.65 - 5.5V
V
DD =
1.70 - 2.95V
I2
C Bus SCL
SDA
{
Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives
an adequate “product liability indemnification insurance agreement.” Supertex inc. does not assume responsibility for use of devices described, and limits its liability
to the replacement of the devices determined defective due to workmanship. No responsibility is assumed for possible omissions and inaccuracies. Circuitry and
specifications are subject to change without notice. For the latest product specifications refer to the Supertex inc. (website: http//www.supertex.com)
©2014
Supertex inc. All rights reserved. Unauthorized use or reproduction is prohibited.
Supertex inc.
1235 Bordeaux Drive, Sunnyvale, CA
94089
T
el: 408-222-8888
www.supertex.com
2
HV892DB1
Doc.# DSDB-HV892DB1
B032114
HV892DB1 Circuit Schematic
Bill of Materials
Part Description Value Tolerance Rating Package Manufacturer Part Number
CIN Ceramic capacitor 20% 6.3V 0603 Any ---2.2ÎĽF
CHV Ceramic capacitor 4.7nF 10% 100V 0603 Any ---
IC1Lens driver - - - 4x4 DFN Supertex HV892K7-G
I2C Bus VDD =
1.70 -2.95V
CHV
4.7nF
CIN
2.2µF
Liquid Lens
100 - 200pF
SDA
SCL
VIN
GND
OUT1
OUT2
VDD VDD
SDA
SCL
GND1
VIN
HV
OUT1
OUT2
GND2
HV892
VIN =
2.65 -5.50V
Operation
A single byte (AMP) written to the HV892 controls the opera-
tion of the driver. Setting AMP = 00h causes the HV892 to
go into low power standby mode. Setting AMP = 01h to FFh
controls output amplitude in 255 monotonic steps.
VOUT(RMS)
= 9.6VRMS + AMP • 208mVRMS
The HV892 is write-only. No readback of the AMP byte is
possible.
The HV892’s 7-bit address is 0100011b. For large quantity
orders, other 7-bit addresses may be obtained.
The resistors shown on the above schematic are the I2C bus’
normal pull-ups. No additional pull-ups are required. Exter-
nally supplied VDD is the I2C bus’ reference voltage.
Externally supplied VIN should be ramped up in less than
2.0ms to ensure the driver starts-up in standby mode. If
brought up slower, the driver may not start-up in standby
mode, with output amplitude at an indeterminate level. In
this case, writing AMP = 00h brings the driver to standby
mode. No damage will occur if VIN is brought up slower than
2.0ms.
Light capacitive loads may result in waveform distortion.
This is due to the output pins being held at a high-Z state for
a portion of the waveform. Without adequate capacitance
to hold up the voltage, some droop may be observed when
DC-loaded by oscilloscope probes.
To avoid loading down the outputs, use instruments hav-
ing at least 10MΩ input impedance when taking measure-
ments. While many voltmeters may have a very high input
resistance on the DC scale, they frequently have only 1.0MΩ
input impedance on the AC scale. Also, be sure to use a
voltmeter with true RMS capability.


Produktspezifikationen

Marke: Microchip
Kategorie: Nicht kategorisiert
Modell: HV892DB1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Microchip HV892DB1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Microchip

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-