Microchip CEC1702 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Microchip CEC1702 (25 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 26 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/25
2017-2021 Microchip Technology Inc. DS00002402D-page 1
INTRODUCTION
This application note provides information on design considerations for a printed circuit board (PCB) for the Microchip
CEC1702 device.
The design of the PCB requires care to provide good supply and ground paths; in addition, other design issues are
addressed in this document.
The functional blocks in the CEC1702 have different requirements for routing and external connections, which are also
outlined in this application note.
Please see References for device-level information such as V
CC1 power planes, and mechanical package information
for the 84-Pin WFBGA.
This document includes the following topics:
Section 1.0, "General Layout Considerations," on page 2
Section 2.0, "Miscellaneous Considerations," on page 9
Section 3.0, "JTAG Design and Layout Guide," on page 19
Audience
This document is written for a reader that is familiar with hardware design. The goal of this application note is to provide
information about sensitive areas of the CEC1702 PCB layout.
References
The following documents should be referenced when using this application note. Please contact your Microchip repre-
sentative for availability.
Microchip CEC1702 Data Sheet
Microchip CEC1702 EVB Reference Schematic
• I2C-bus specification and user manual, Rev. 6 - 4 April, 2014 or later (see www.nxp.com/documents/user_manual/
UM10204.pdf)
Package Information
The CEC1702 device is currently available in the following package:
CEC1702 for 84-pin, WFBGA
AN2402
PCB Layout Guide for CEC1702
Author: Tom Tse
Microchip Technology Inc.
AN2402
DS00002402D-page 2 2017-2021 Microchip Technology Inc.
1.0 GENERAL LAYOUT CONSIDERATIONS
This section describes layout considerations for the CEC1702 device. This includes the following topics:
Section 1.1, "Decoupling Capacitors," on page 2
Section 1.2, "32.768kHz Crystal Oscillator," on page 4
Section 1.3, "CAP Pins, AVSS/GND Connection," on page 5
Section 1.4, "PCB Mounted Analog Power Supply Filter for PLL Usage," on page 5
Section 1.5, "BGA Package PCB Layout Considerations," on page 6
1.1 Decoupling Capacitors
This section includes the following topics:
Section 1.1.1, "CEC1702 WFBGA Capacitors," on page 2
Decoupling capacitors should be placed as close to the chip as possible to keep series inductance low. When the capac-
itors are mounted on the bottom side of the PCB, the capacitors are connected to the ground plane from the bottom
layer directly using the shortest path to the device. Each VCC pin should have a 0.1 F capacitor located as close to
the pin as possible. Bypass capacitors should be placed close to the supply pins of the CEC1702 with short and wide
traces.
The CEC1702 has an integrated voltage regulator to supply the core circuitry. Decoupling this regulator requires a crit-
ical capacitor of 1F on the CAP pin. ESR of this 1F capacitor, including the routing resistance, must be less than 100
mOhm.
Capacitors may carry large currents that generate magnetic fields, inducing noise on nearby traces. Sensitive traces
such as the 32kHz crystal should be separated by at least five times the trace width from decoupling capacitors when
possible.
Connecting decoupling caps to power and ground planes using two vias per pad will reduce series inductance.
FIGURE 1-1: on page 3 shows decoupling for the CEC1702 84-pin WFBGA.
The VCC pin decoupling capacitors can use any typical 16V 10% Ceramic. See also the CEC1702 EVB Schematics
and Bill of Materials.
1.1.1 CEC1702 WFBGA CAPACITORS
Figure 1-1 shows decoupling for the CEC1702 84-pin WFBGA package.
Note: The capacitors can use any typical 16V 10% ceramic.
2017-2021 Microchip Technology Inc. DS00002402D-page 3
AN2402
FIGURE 1-1: CEC1702 DECOUPLING IN 84-PIN WFBGA PACKAGE
B
CEC1702 WFBGA (Bottom View)
Note: (For Part Numbers see CEC1702 DC Assy 6808 Schematic)
C9 = 0.1uF on VBAT
C10 = 0.1uF on VTR1
C11 = 0.1uF on VTR2
C14 = 0.1uF on VTR_REG
C13 = 0.1uF & C20 = 22uF between VTR_PLL & VSS_PLL
C7 = 1uF Low ESR +/-20% <100 mOhm on VR_CAP (X5R or X7R)
Y1 = 9pF load crystal, with C5, C6 = 10pF decoupling
A
D
C
F
E
H
G
K
J
146 58 710 9
C14
23
C9
2 Vias to VTR
2 Vias to GND
C10
C7
1uF
Low
ESR
C11
C5
Y1
C6
C13 C20


Produktspezifikationen

Marke: Microchip
Kategorie: Nicht kategorisiert
Modell: CEC1702

Brauchst du Hilfe?

Wenn Sie Hilfe mit Microchip CEC1702 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Microchip

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-