Metabo NV50A1 Bedienungsanleitung
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂŒr Metabo NV50A1 (69 Seiten) in der Kategorie Hefter. Dieser Bedienungsanleitung war fĂŒr 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/69
Instruction and safety manual
Manuel dâinstructions et de sĂ©curitĂ©
Instrucciones y manual de seguridad
Model
ModĂšle
Modelo NV 83A2 âą NV 65AC âą NV 50A1 Nailer
Cloueur
Clavador
NV83A2 NV65AC NV50A1
DANGER
Improper use of this Nailer can result in death or serious injury!
This Manual contains important information about product safety.
Read and understand this Manual before operating the Nailer.
Never allow anyone who has not reviewed this manual to use the tool.
This manual should be stored in safe place.
DANGER
Une utilisation incorrecte et sans respecter la sĂ©curitĂ© de ce cloueur risque dâentraĂźner la
mort ou des blessures graves !
Ce manuel renferme des instructions importantes sur la sĂ©curitĂ© de lâoutil.
Lire et bien assimiler ce manuel avant dâutiliser le cloueur.
Cet outil ne doit jamais ĂȘtre utilisĂ© par une personne nâayant pas pris connaissance du manuel.
Ce mode dâemploi doit ĂȘtre conservĂ© dans un endroit sĂ»r.
PELIGRO
ÂĄLa utilizaciĂłn inadecuada e insegura de este clavador puede resultar en lesiones serias o
en la muerte!
Este manual contiene informaciĂłn importante sobre la seguridad del producto.
Lea y entienda este manual antes de utilizar el martillo neumĂĄtico.
La herramienta no deberĂĄ utilizarse sin haber leĂdo previamente este manual.
Este manual debe ser guardado en un lugar seguro.
2
English
ATTENTION : USERS OF metabo HPT NAILERS
(Read this information carefully for your satisfaction and safety)
This metabo HPT nailer has a STANDARD CONTACT TRIP MECHANISM (Bounce Fire). An OPTIONAL
SEQUENTIAL TRIP MECHANISM kit (SINGLE SHOT) is available as shown below.
Models Order part number
NR83A, NR83AA, NV83A, NV65AC, VH-650, NT65A2, NV50AA, NV50A1, NV50AP,
NR83AA2, N5008AC, NV50AP2, NV83A2, N5024A
876762
NV45AB, NV45AB2, NV45AE 878226
NR90AC, NV65AH, NR90AA, NV45AC, NR90AC2 881973
NT65AA, NT65MA 880414
NV75AG 883991
To order in U.S. call toll free 1-800-706-7337. In Canada call toll free 1-800-970-2299.
THE STANDARD CONTACT TRIP MECHANISM (Bounce Fire) is for use where rapid fastener placement is
desired and must be operated in accordance with the following âMethods of Operationâ.
This metabo HPT nailer is equipped with a push lever and does not operate unless the push lever is depressed
(upward position). There are two methods of operation to drive nails with this Nailer.
1. Intermittent operation (Trigger Fire)
2. Continuous operation (Push Lever Fire)
(1) Intermittent operation (Trigger Fire)
1
Position the nail outlet on the workpiece with ïŹ nger oïŹ the trigger.
2
Depress the push lever ïŹ rmly until it is completely depressed.
3
Pull the trigger to drive a nail.
4
Remove ïŹ nger from the trigger.
To drive another nail, move the nailer along the workpiece and repeat this procedure.
(2) Continuous operation (Push Lever Fire)
1
Pull the trigger with the push lever pointing towards but not touching the workpiece.
2
Depress the push lever against the workpiece to drive a nail.
3
Move the nailer along the workpiece with a bouncing motion. Each depression of the push lever will drive a nail.
As soon as the desired number of nails have been driven, remove ïŹ nger from the trigger.
WAR NING
: Keep your ïŹ nger oïŹ the trigger except during fastening operation, because serious
injury could result if the push lever accidentally contacts you or others in work area.
WAR NING
: Keep hands and body away from the discharge area. The nailer with contact trip
mechanism may bounce from the recoil of driving a fastener and unwanted subsequent
fastener may be driven, possibly causing injury.
THE OPTIONAL SEQUENTIAL TRIP MECHANISM (SINGLE SHOT PARTS) is for use where precision fastener
placement is desired and must be operated in accordance with the following âMethod of Operationâ.
You must ïŹ rst depress the push lever (upward position) where you want to drive a nail and then pull the trigger.
After the each nail is driven, completely release the trigger and lift the tool oïŹ the work surface. An OPTIONAL
SEQUENTIAL TRIP MECHANISM may reduce the possibility of bodily injury to you or others in the work area. This
is because it is less likely to drive an unwanted nail if you keep the trigger pulled and accidentally bump the push
lever against yourself or others. An OPTIONAL SEQUENTIAL TRIP MECHANISM may also reduce the speed of
operation compared to the standard contact trip mechanism.
NOTE : Both STANDARD CONTACT TRIP MECHANISM and OPTIONAL SEQUENTIAL TRIP MECHANISM are safe
if used as described above and according to all warnings and instructions.
3
English
IMPORTANT SAFETY INFORMATION
Read and understand tool labels and all of the operating instructions, safety precautions and warnings
in this manual before operating or maintaining this Nailer.
Failure to follow warnings could result in DEATH or SERIOUS INJURY
Most accidents that result from the operation and maintenance of Nailers are caused by the failure to observe basic
safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it
occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the âSAFETYâ section of this Manual and in the sections which contain the
operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identiïŹ ed by DANGERS and WARNINGS
on the Nailer and in this Manual.
NEVER use this Nailer for applications other than those speciïŹ ed in this Manual.
DEFINITIONS OF SIGNAL WORDS
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or
may cause machine damage.
NOTE emphasizes essential information.
EXPLANATION OF THE NAILING ACTION OF THE metabo HPT NAILER
â
CONTACT ACTUATION MECHANISM:
First, press the push lever against the wood; next, pull the trigger to drive the fastener.
First, pull the trigger; next, press the push lever against the wood to drive the fastener.
If the Trigger is held back, a nail will be driven each time the Push Lever is pressed against the wood.
Produktspezifikationen
| Marke: | Metabo |
| Kategorie: | Hefter |
| Modell: | NV50A1 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Metabo NV50A1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Hefter Metabo
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
Bedienungsanleitung Hefter
- Hefter Kensington
- Hefter Rapoo
- Hefter Targus
- Hefter Makita
- Hefter Parkside
- Hefter Vonroc
- Hefter Whirlpool
- Hefter Powerfix
- Hefter Meister
- Hefter Rapid
- Hefter Ryobi
- Hefter Topcraft
- Hefter DeWalt
- Hefter Hikoki
- Hefter Hitachi
- Hefter Workzone
- Hefter Sencor
- Hefter Fieldmann
- Hefter Rexel
- Hefter Silverline
- Hefter Holzmann
- Hefter MSW
- Hefter President
- Hefter Genesis
- Hefter Proline
- Hefter Fellowes
- Hefter Milwaukee
- Hefter Craftsman
- Hefter Powerplus
- Hefter Sun Joe
- Hefter Aqua Joe
- Hefter Porter-Cable
- Hefter Iluv
- Hefter Werckmann
- Hefter Neo
- Hefter Syscom
- Hefter Surtek
- Hefter CTA Digital
- Hefter Klein Tools
- Hefter Smart365
- Hefter Mannesmann
Neueste Bedienungsanleitung fĂŒr -Kategorien-
15 Oktober 2024
2 Oktober 2024
1 Oktober 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
4 September 2024