Metabo G12SE3 Bedienungsanleitung
Metabo
Schleifmaschine
G12SE3
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metabo G12SE3 (41 Seiten) in der Kategorie Schleifmaschine. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/41
Model
Disc Grinder
Modèle
Meuleuse à disque
Modelo
Amoladora angular
G 12SE3 • G 13SE3
DOUBLE INSULATION
DOUBLE ISOLATION
AISLAMIENTO DOBLE
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la
mort ou de sérieuses blessures corporelles!
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.
Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce
mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent
l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and
understand this manual BEFORE operating the power tool. Please keep this manual
available for other users and owners before they use the power tool. This manual should be
stored in safe place.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar
en lesiones de gravedad o la muerte!
Este manual contiene información importante sobre la seguridad del producto. Lea y com-
prenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para
que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual
debe ser guardado en un lugar seguro.
G12SE3
IMPORTANT SAFETY INFORMATION
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before
operating or maintaining this power tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety
rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,
and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which contain
the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identifi ed by WARNINGS on the power tool
and in this Instruction Manual.
NEVER use this power tool in a manner that has not been specifi cally recommended by metabo HPT.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or
may cause machine damage.
NOTE emphasizes essential information.
SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the
risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts.
Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the infl uence of drugs, alcohol or
medication.
2
English
A moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off -position before connecting
to power source and/or battery pack, picking
up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used.
Use of dust collection can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off .
Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may aff ect the
power tool’s operation.
If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous
situation.
5) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool
is maintained.
SAFETY WARNINGS COMMON FOR
GRINDING OPERATIONS
a) This power tool is intended to function as a grinder.
Read all safety warnings, instructions, illustrations
and specifi cations provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fi re and/or serious injury.
b) Operations such as sanding, wire brushing,
polishing or cutting-off are not recommended to
be performed with this power tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
c) Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Accessories running faster than their rated speed can
break and fl y apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted
by fl anges, the arbour hole of the accessory must
fi t the locating diameter of the fl ange.
3
English
Produktspezifikationen
| Marke: | Metabo |
| Kategorie: | Schleifmaschine |
| Modell: | G12SE3 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Metabo G12SE3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schleifmaschine Metabo
8 Oktober 2024
9 September 2024
6 September 2024
6 September 2024
30 August 2024
28 August 2024
28 August 2024
27 August 2024
26 August 2024
25 August 2024
Bedienungsanleitung Schleifmaschine
- Schleifmaschine SilverCrest
- Schleifmaschine Cotech
- Schleifmaschine Makita
- Schleifmaschine Bosch
- Schleifmaschine Flex
- Schleifmaschine Parkside
- Schleifmaschine Vonroc
- Schleifmaschine AEG
- Schleifmaschine Gorenje
- Schleifmaschine Mesko
- Schleifmaschine Black And Decker
- Schleifmaschine Cocraft
- Schleifmaschine FERM
- Schleifmaschine Ryobi
- Schleifmaschine Skil
- Schleifmaschine Topcraft
- Schleifmaschine Trotec
- Schleifmaschine Maestro
- Schleifmaschine Eibenstock
- Schleifmaschine Hilti
- Schleifmaschine Bort
- Schleifmaschine DeWalt
- Schleifmaschine Einhell
- Schleifmaschine Elu
- Schleifmaschine Festool
- Schleifmaschine Maktec
- Schleifmaschine Worx
- Schleifmaschine Nuova Simonelli
- Schleifmaschine Hikoki
- Schleifmaschine Hitachi
- Schleifmaschine Hyundai
- Schleifmaschine Hazet
- Schleifmaschine Kress
- Schleifmaschine Max
- Schleifmaschine Stanley
- Schleifmaschine Güde
- Schleifmaschine Scheppach
- Schleifmaschine Workzone
- Schleifmaschine United Office
- Schleifmaschine Meec Tools
- Schleifmaschine AquaPur
- Schleifmaschine Dremel
- Schleifmaschine Fieldmann
- Schleifmaschine King Craft
- Schleifmaschine Proxxon
- Schleifmaschine Westfalia
- Schleifmaschine Profitec
- Schleifmaschine Dedra
- Schleifmaschine DURO
- Schleifmaschine Graphite
- Schleifmaschine Pattfield
- Schleifmaschine Silverline
- Schleifmaschine Holzmann
- Schleifmaschine Florabest
- Schleifmaschine Herkules
- Schleifmaschine Aerotec
- Schleifmaschine Huvema
- Schleifmaschine Stomer
- Schleifmaschine Yato
- Schleifmaschine Baumr-AG
- Schleifmaschine Genesis
- Schleifmaschine ABB
- Schleifmaschine Batavia
- Schleifmaschine Dolmar
- Schleifmaschine Bavaria
- Schleifmaschine Brüder Mannesmann
- Schleifmaschine Milwaukee
- Schleifmaschine Toolcraft
- Schleifmaschine Fein
- Schleifmaschine Powertec
- Schleifmaschine Craftsman
- Schleifmaschine Defort
- Schleifmaschine Powerplus
- Schleifmaschine Alpha Tools
- Schleifmaschine Ozito
- Schleifmaschine Kawasaki
- Schleifmaschine Solo
- Schleifmaschine Ridgid
- Schleifmaschine Porter-Cable
- Schleifmaschine Dolmar(Makita)
- Schleifmaschine Duro Pro
- Schleifmaschine Ergofix
- Schleifmaschine Felisatti
- Schleifmaschine Gamma
- Schleifmaschine Global
- Schleifmaschine Goon
- Schleifmaschine Gude Pro
- Schleifmaschine Tanaka
- Schleifmaschine Bunn
- Schleifmaschine Neo
- Schleifmaschine Meister Craft
- Schleifmaschine Malmbergs
- Schleifmaschine Yamato
- Schleifmaschine Truper
- Schleifmaschine Victoria Arduino
- Schleifmaschine RIKON
- Schleifmaschine Einhell Bavaria
- Schleifmaschine Proviel
- Schleifmaschine Budget
- Schleifmaschine McKenzie
- Schleifmaschine Kwb
- Schleifmaschine Ergotools Pattfield
- Schleifmaschine FIXIT
- Schleifmaschine THUN
- Schleifmaschine Rodcraft
- Schleifmaschine Bavaria By Einhell
- Schleifmaschine ATI-ZDL
- Schleifmaschine Gladiator
- Schleifmaschine Handwerk
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
14 Oktober 2024
13 Oktober 2024
7 Oktober 2024
5 Oktober 2024
3 Oktober 2024
3 Oktober 2024
2 Oktober 2024
2 Oktober 2024
30 September 2024