Mean Well RSP-2400-24 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Mean Well RSP-2400-24 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
2400W Single Output Power Supply
RSP 2400 - series
Model: 2400 24RSP- - Test Report 1 / 6
MODEL:
:
:
::RSP- - 2400 24
OUTPUT FUNCTION TEST
NO
TEST ITEM
SPECIFICATION
TEST CONDITION
VERDICT
1 RIPPLE & NOISE
V1
:
150
mVp-p (Max )
I/P
:
230VAC
O/P:FULL LOAD
Ta:25℃
V1
:
95 p-mV p (Max )
P
2 OUTPUT VOLTAGE
ADJUST RANGE
CH1
:
22 V~ 28 V
I/P
:
230 VAC
O/P:MIN LOAD
Ta:25℃
21.31
21.30
V~
V~
28.92
28.92
V/ 230 VAC
V/ 180 VAC
P
3 OUTPUT VOLTAGE
TOLERANCE
V1
:
1 %~ - 1 % (Max)
I/P
:
180VAC / 264 VAC
O/P:FULL/ MIN LOAD
Ta:25℃
V1
:
0.05 %~
- % 0.05
P
4 LINE REGULATION V1: - 0.5 %~ 0.5 % (Max)
I/P:180VAC ~ 264 VAC
O/P:FULL LOAD
Ta:25℃
V1:
0.03 %~
- % 0.03
P
5 LOAD REGULATION
V1
:
-0.5 %~ 0.5 % (Max)
I/P
:
230 VAC
O/P:FULL ~MIN LOAD
Ta:25℃
V1
:
0.03 %~ - % 0.03
P
6 SET UP TIME
230VAC
:
1000
ms (Max)
I/P
:
230 VAC
O/P:FULL LOAD
Ta:25℃
230VAC/
533
ms
P
7 RISE TIME
230VAC
:
80
ms (Max)
I/P
:
230 VAC
O/P:FULL LOAD
Ta:25℃
230VAC/
57
ms
P
8 HOLD UP TIME
230VAC
:
12
ms (TYP)
I/P
:
230 VAC
O/P:FULL LOAD
Ta:25℃
230VAC/
25.7
ms
P
9 OVER/UNDERSHOOT
TEST
< + 5% I/P: 230 VAC
O/P:FULL LOAD
Ta
:
25
℃
TEST: < 5 %
P
10 DYNAMIC LOAD
V1
:
2400 -p mVp
I/P
:
230 VAC
O/P:FULL /Min LOAD 90%DUTY/
1KHZ
Ta:25℃
229 -p mVp
P
2400W Single Output Power Supply
RSP 2400 - series
Model: 2400 24RSP- - Test Report 2 / 6
INPUT FUNCTION TEST
NO
TEST ITEM
SPECIFICATION
TEST CONDITION
RESULT
VERDICT
1 INPUT VOLTAGE RANGE 180VAC~264 VAC I/P:TESTING
O/P:FULL LOAD
Ta:25℃
171 V~264V
P
I/P:
- - V LOW LINE 3V= 177
- HIGH LINE+15%=300 V
O/P:FULL/MIN LOAD
ON:30 Sec . OFF:30 Sec 10MIN
( AC POWER ON/OFF NO DAMAGE )
TEST: OK
2 INPUT FREQUENCY RANGE 47HZ ~63 HZ
NO DAMAGE OSC
I/P
:
180 VAC ~ 264 VAC
O/P:FULL~MIN LOAD
Ta
:
25
℃
TEST
:
OK
P
3 POWER FACTOR 0.95 / 230 VAC(TYP) I/P: 230 VAC
O/P:FULL LOAD
Ta:25℃
PF= 0.965 / 230 VAC
P
4 EFFICIENCY 90 % (TYP) I/P: 230 VAC
O/P:FULL LOAD
Ta
:
25
℃
90.8 %
P
5 INPUT CURRENT
230V/
12
A (TYP)
I/P
:
230 VAC
I/P: 180 VAC
O/P:FULL LOAD
Ta:25℃
I =
11.94
A/ 230 VAC
P
180 80V/ 15.5 A (TYP) I = 15.41 A/ 1 VAC
6 INRUSH CURRENT 230V/ 60 A (TYP) I/P: 230 VAC
O/P:FULL LOAD
Ta:25℃
I = 55 A/ 230 VAC
P
COLD START
7 LEAKAGE CURRENT < 2 mA / 240 VAC
I/P
:
264 VAC
O/P:Min LOAD
Ta:25℃
L-FG
:
1.3
mA
P
N-FG:
1.35 mA
PROTECTION FUNCTION TEST
NO
TEST ITEM
SPECIFICATION
TEST CONDITION
RESULT
VERDICT
1 OVER LOAD PROTECTION 2 % 100%~11 I/P: 230 VAC
O/P:TESTING
Ta:25℃
106.6%/ 230 VAC
Constant Current Limiting
P
2 OVER VOLTAGE PROTECTION
CH1
:
28.8V~ 33.6V
I/P
:
230 VAC
O/P:MIN LOAD
Ta:25℃
31.4V/ 230 VAC
Shut down Re- power ON
P
3 OVER TEMPERATURE PROTECTION SPEC:
TSW1: + 5 100 ℃O.T.P
detect on heatsink of power
transistor
TSW2: 85 + 5 ℃O.T.P
detect on heatsink of O/P diode
NO DAMAGE
I/P: 230 VAC
O/P:FULL LOAD
O.T.P. Active
Shut down o/p voltage,recovers
automatically after temperature
goes down
P
4 SHORT PROTECTION SHORT EVERY OUTPUT
1 HOUR NO DAMAGE
I/P: 264 VAC
O/P:FULL LOAD
Ta:25℃
NO DAMAGE
CN3 PIN9- 10 SHORT:
Shut down Re power ON-
CN3 PIN9-10 OPEN:
Current Limit
P
2400W Single Output Power Supply
RSP 2400 - series
Model: 2400 24RSP- - Test Report 3 / 6
CONTROL FUNCTION TEST
NO
TEST ITEM
SPECICATION
TEST CONDITION
RESULT
VERDICT
1
AUXILIARY POWER
(AUX)
12V @ 0.1A
(Only for Remote ON/OFF control )
I/P: 230 VAC
O/P:FULL LOAD
Ta
:
25
℃
11.907V
P
2 REMOTE CONTROL Table1.1 Fig1.2(a)(b)(c)
Specification of Remote ON/OFF
I/P
:
230 VAC
O/P:FULL LOAD
Ta:25℃
Connection
Method
Fig1.2(a)
Fig1.2(b)
Fig1.2(c)
SW
Logic
Output
on
SW
Open
SW
Open
SW
Close
Output
off
SW
Close
SW
Close
SW
Open
P
3 ALARM SIGNAL
OUTPUT
Table2.1 Explanation of alarm
Function
Description
P OK
The signal is "Low" when the power
supply is
80% of the rated output
voltage-Power OK
The signal turns to be "High" when
the power supply
is under 80% of the rated output
voltage-Power Fail
I/P
:
230 VAC
O/P:FULL LOAD
Ta:25℃
Output of alarm
(P OK, relay contact)
Output of alarm
(P OK2, TTL Signal)
Low
(0.5V max at 500mA)
Low
(0.5V max at 10mA)
High or open
(External applied
voltage 500mA max.)
High or open
(External applied
voltage 10mA max.)
P
4
OUTPUT VOLTAGE
PROGRAMMABLE(PV)
(1) Adjustment of output voltage is possible
between 20~110%(Typ.) of the rated
output which is shown in Fig. 3.1
(2) Connecting a resistor externally
between PV and S on CN1 or CN2 that is -
shown in Fig. 3.2
I/P: 230 VAC
O/P:NOL LOAD
Ta:25℃
PV=1V , Vout= 4.908 V
PV=3V , Vout= 14.808 V
PV=5V , Vout= 24.29 V
PV=5.5,Vout= 26.54 V
P
5 CURRENT SHARING PSU1-PSU2 < 10%
I/P
:
230 VAC
O/P :90%/50%
LOAD
Ta:25℃
O/P
:
90% LOAD
PSU1:89.3 A
PSU2:89.8 A
PSU3
:
91.5 A
P
O/P:50%
PSU1:48.8 A
PSU2:49.4 A
PSU3
:
52.0 A
6 REMOTE SENSE >0.25V
I/P
:
230 VAC
O/P:FULL LOAD
Ta
:
25
℃
> 0.25 V
P
7 FAN SPEED
CONTROL
------- I/P: 230 VAC
O/P :FULL
/NOLOAD
Ta
:
25
℃
NO LOAD Fan Voltage= 7.32 V
100% LOAD Fan Voltage= V 12.549 P


Produktspezifikationen

Marke: Mean Well
Kategorie: Nicht kategorisiert
Modell: RSP-2400-24

Brauchst du Hilfe?

Wenn Sie Hilfe mit Mean Well RSP-2400-24 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Mean Well

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-