Martin RoboZap Bedienungsanleitung

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Martin RoboZap (4 Seiten) in der Kategorie niet gecategoriseerd. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
RoboZap
users guide
2
I N T R O D U C T I O N
The RoboZap is a high-performance, intelligent, special-effect lighting unit which features:
Multi-faceted, asymmetrically mounted, variable-speed rotating mirror
High quality stepper motors
2x250W, 120V ENH lamps
2x4 dichroic colors, plus white and black-out
The speed of the color change is variable and can be individually set for each of the lamps.
Color mixing (adjacent colors)
8 manually selectable gobos for each lamp
Variable speed shutter for strobe effect
Precision optics
Adjustable focus
Efficient dual fan cooling
Can be controlled by Martin 2501 (32 pcs.), 2308 (8 pcs.), 2032 (32 pcs.), 3032 (96 pcs.).
Can be controlled by DMX 512 via Martin Interface.
Can run without controller using built-in random-sequence programmes with and without music trig. (Stand
alone)
Built-in microphone for music triggering.
H OW TO I N S TA L L T H E RO B O Z A P
1. Remove the 4 knurled screws and remove the casing. The lamps can now be installed.
2. The desired gobos can be selected by turning the gobo wheel.
3. Replace the casing and tighten the screws.
4. Set the mains voltage switches (on the opposite end of the unit from the DIP switches) to the
local mains voltage (115/230V).
C A U T I O N
It is extremely important that BOTH switches are set to the correct voltage.
O P E R AT I N G W I T H A C O N T R O L L E R
C O N N E C T I N G T H E S E R I A L T R A N S M I S S I O N L I N K
1. Connect the RoboZap, or the first unit in the link, to the controller, using the 10 metre XLR cable which
came with the controller.
2. To interconnect the units in the link you need an XLR-XLR cable e.g. a standard balanced micro-
phone cable. Your local Martin Professional dealer can supply this.
3. The units should be connected together in an order which gives the minimum cable length. This
order has no influence on the address as far as the controller is concerned.
4. The termination plug which came with the controller is plugged into the unused XLR socket on
the last unit on the link.
S E T T I N G T H E O P E R AT I N G A D D R E S S O F E AC H RO B O Z A P
Set the DIP switch to the address number you want each RoboZap to use. Please refer to the Address Settings
table below.
I M P O R T A N T
THE CONTROLLER MUST NOT BE SWITCHED ON UNTIL 2 MINUTES
AFTER THE UNITS HAVE BEEN SWITCHED ON.
3
RoboZap
O P E R AT I N G W I T H O U T A C O N T R O L L E R ( S TA N D A L O N E )
When operating the RoboZap without a controller you have a choice of programs. Please refer to the Sequence Settings
table below and set the DIP switches to the settings for the desired program. If you choose a music trig program, the
program will start together with the music, otherwise the pre-programmed sequences start immediately.
Because the mains supply for the lamp has its own mains cable you can leave the motors, electronics and cooling fans
on and manually switch the lamp on and off - also with your own lighting controller if you have one.
C A U T I O N
Lamps are very fragile when hot: do not move the units until they are cool.
This appendix shows the different address and sequence settings for the DIP switch on the RoboZap. The above set-
tings refer to the pin(s) on the DIP switch which are set to the ON position.
Address settings
Unit no. ON pins Unit no. ON pins
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
1,2
3
1,3
2,3
1,2,3
4
1,4
2,4
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
5
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1,5
2,5
1,2,5
3,5
1,3,5
2,3,5
1,2,3,5
4,5
1,4,5
2,4,5
1,2,4,5
3,4,5
1,3,4,5
2,3,4,5
1,2,3,4,5
6
Sequence settings
Description ON pins
Test
Demo 1
Demo 1, with music trig
Demo 2
Demo 2, with music trig
Demo random 1
Demo random 1, with music trig
Demo random 2
Demo random 2, with music trig
Preprogram chase
Preprogram chase, with music trig
Rotation ramp
Rotation ramp, with music trig
Mechanical stop (For service use)
Adjustment (For service use)
Led chase (For service use)
none
2,6
1,2,6
3,6
1,3,6
2,3,6
1,2,3,6
4,6
1,4,6
2,4,6
1,2,4,6
3,4,6
1,3,4,6
1,3,4,5,6
3,4,5,6
2,4,5,6

Produktspezifikationen

Marke: Martin
Kategorie: niet gecategoriseerd
Modell: RoboZap

Brauchst du Hilfe?

Wenn Sie Hilfe mit Martin RoboZap benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung niet gecategoriseerd Martin

Bedienungsanleitung niet gecategoriseerd

Neueste Bedienungsanleitung für -Kategorien-