Martin MAC Viper Quadray Bedienungsanleitung

Martin Erleichterung MAC Viper Quadray

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Martin MAC Viper Quadray (8 Seiten) in der Kategorie Erleichterung. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/8
Martin MAC Viper Quadrayâ„¢ Quadray Installation and DMX Control Guide 1
MAC Viper Quadrayâ„¢ Module
Installation and Control Guide
Introduction
This Guide explains how to install the Martin MAC Viper Quadrayâ„¢ Module, P/N 91614052, on a Martin MAC
Viper AirFXâ„¢ fixture and control the Quadray functions via DMX.
Installation takes only a few minutes. If you keep the standard components you remove when you install the
Quadray module, the Quadray components can be uninstalled and the fixture returned to standard configuration
at any time.
Warning! Follow all the safety precautions in the MAC Viper AirFX user manual and use the
manual for reference when installing the Quadray Module and using the modified product. The
user manual is supplied with fixtures, but check that you have the latest revision of the user
manual. This is available for download from the Product Support page for the MAC Viper AirFX
at www.martin.com
Warning! Disconnect the fixture from power and allow to cool for at least 2 hours and 45
minutes before starting work.
Warning! The Quadray Module must be installed by qualified professional technicians only.
Read all of this Installation Guide carefully before starting to install the module.
Important! Make sure that the front of the head does not face the sun or any other strong light
source directly for longer than a few seconds at any time. Lenses can focus the sun's rays
inside the fixture, causing internal damage and creating a possible fire risk
Important! Do not use concentrated alcohol solutions, abrasive products or solvents to clean
the components in the Quadray Module. If wiping with a soft, lint-free cloth dampened with
distilled water is not effective, damp the cloth with distilled water containing 20% isopropyl
alcohol in solution.
If you have any questions about how to install the Quadray Module or use it safely, please contact your local
Martin distributor (see www.martin.com/distributors for details) or call the Martin 24-hour service hotline on +45
8740 0000, or in the USA on 1-888-tech-180.
Software compatibility
MAC Viper AirFX firmware version 1.2.0 or later is required for operation with the Quadray Module. The latest
version of the MAC Viper AirFX firmware is available for download from the MAC Viper AirFX Product Support
page on the Martinâ„¢ website at www.martin.com
© 2013 Martin Professional A/S. Olof Palmes Allé 18, DK-8200 Aarhus N, Denmark. Information subject to change without notice. Martin
Professional A/S and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic
loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this installation note. The
Martin logo, the Martin name and all other trademarks in this document pertaining to services or products by Martin Professional A/S or
its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.
P/N 35000629 Rev. C
2 Martin MAC Viper Quadrayâ„¢ Module Installation and DMX Control Guide
Preparation
The Quadray Module accessory contains the following items:
• MAC Viper Quadray Module with integral wireset
• This Installation Guide
Keep the protective packaging supplied with the module for possible re-use.
Without damaging the wiring, remove the adhesive tape that is applied to avoid damage or loss during transport:
tape holds the safety wire and wireset together and retains the two screws in the module connector on the end of
the wireset.
Calibration values for each individual module are printed on a label on the module connector. Four values are
given for the four lenses . Each time you install a Quadray Module on a fixture, you must enter its L1 to L4
calibration values in the CALIBRATION menu in the fixture’s control panel. Note these values and store them for
future use when installing the module on other fixtures.
Installation procedure
Warning! Disconnect from power and allow to cool for 30 minutes before opening the head.
To install the Quadray Module on a standard Martin MAC Viper AirFX fixture:
1. Disconnect the fixture from power and allow components to cool for 30 minutes.
2. Place the fixture on a secure work surface. Tilt the head vertically upwards and apply the tilt lock.
3. See Figure 1. Remove the top head cover by loosening its Torx 25 captive retaining screws A until the screws
turn freely (the top head cover is on top of the head with the text on the back of the head facing the right way
up). Lift the front of the cover slightly away from the head, then slide the cover towards the front of the head to
release the rear of the cover. You can allow the head cover to hang on its safety wire, but for easiest access
press the cover’s safety wire retaining clip B in towards the head chassis, slide the clip down until you can
remove it, then remove the head cover completely from the fixture.
4. See Figure 2. Release the four screws from the front lens assembly, then
release the front lens safety attachment. Remove the front lens assembly
and store it for possible re-use if the fixture is returned to standard
configuration at a later time.
Figure 1: Removing the head covers
A A
B
Figure 2
Martin MAC Viper Quadrayâ„¢ Quadray Installation and DMX Control Guide 3
5. See Figure 3. Line up the Quadray
Module over the head so that the
module’s safety wire will pass through
the cutout in the front of the head above
the safety wire attachment point A and
the module’s wireset will pass through
the cutout B in the opposite side of the
head.
6. Lower the Quadray Module onto the
head, making sure that it sits completely
square to the head. Do not use
excessive force. You may need to rotate
the module slightly to the left and to the
right until you can feel that it has
engaged correctly. Check also that the
safety wire and wireset are not trapped
between the module and the head.
7. See Figure 4. Fasten the module in place by tightening the four
screws on the front of the module.
8. See Figure 5. Pass the Quadray Module’s safety
cable through the hole in the head chassis and A
then into the safety wire attachment point B. Push
and slide the fastener so that it is locked into the
attachment point.
Figure 3
A
B
Figure 4
Figure 5
A
B

Produktspezifikationen

Marke: Martin
Kategorie: Erleichterung
Modell: MAC Viper Quadray

Brauchst du Hilfe?

Wenn Sie Hilfe mit Martin MAC Viper Quadray benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Erleichterung Martin

Martin

Martin ERA 700 Performance IP Bedienungsanleitung

29 August 2024
Martin

Martin Thrill Vertical Fogger Bedienungsanleitung

23 August 2024
Martin

Martin Freekie Bedienungsanleitung

22 August 2024
Martin

Martin P3-100 Bedienungsanleitung

22 August 2024
Martin

Martin MAC Ultra Wash Bedienungsanleitung

21 August 2024
Martin

Martin RUSH MH 4 Beam Bedienungsanleitung

21 August 2024
Martin

Martin RUSH Strobe 1 5x5 Bedienungsanleitung

21 August 2024
Martin

Martin ERA 600 Performance Bedienungsanleitung

21 August 2024
Martin

Martin ERA 400 Performance WRM Bedienungsanleitung

21 August 2024
Martin

Martin MAC 101 Bedienungsanleitung

21 August 2024

Bedienungsanleitung Erleichterung

Neueste Bedienungsanleitung für -Kategorien-

Goobay

Goobay 30780 Bedienungsanleitung

16 Oktober 2024
AFX

AFX Grace GRCP07CBBK Bedienungsanleitung

13 Oktober 2024
AFX

AFX Point PNTP0107L30D1BK Bedienungsanleitung

13 Oktober 2024
Smartwares

Smartwares 20.003.54 Bedienungsanleitung

9 Oktober 2024
Neewer

Neewer TL97C Bedienungsanleitung

8 Oktober 2024
Neewer

Neewer SRP18C Bedienungsanleitung

8 Oktober 2024
Qtx

Qtx Moonglow Bedienungsanleitung

7 Oktober 2024
Blumfeldt

Blumfeldt Shinecube XL Bedienungsanleitung

7 Oktober 2024
Qtx

Qtx HPWash100 Bedienungsanleitung

6 Oktober 2024
BeamZ

BeamZ DJ X5 Bedienungsanleitung

5 Oktober 2024