Makita TW0250 Bedienungsanleitung
Makita
Schraubenmaschine
TW0250
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Makita TW0250 (8 Seiten) in der Kategorie Schraubenmaschine. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/8
1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
DOUBLE INSULATION
IMPORTANT: Read Before Using.
Impact Wrench
TW0250
009625
2
ENGLISH (Original instructions)
SPECIFICATIONS
Model TW0250
Standard bolt M10 - M20
Capacities High tensile bolt M10 - M14
Square drive 12.7 mm
No load speed (min-1) 0-2,300
Impacts per minute 0-2,300
Max. fastening torque 250 N.m
Overall length 251 mm
Net weight 2.2 kg
Safety class /II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END201-5
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
ï½¥ Read instruction manual.
ï½¥ DOUBLE INSULATION
ï½¥ Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible recycling
facility.
ENE036-1
Intended use
The tool is intended for fastening bolts and nuts.
ENF002-1
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
ENG905-1
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
pA) : 93 dB(A)
Sound power level (L
WA) : 104 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
ENG900-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (ah) : 11.0 m/s2
Uncertainty (K) : 2.0 m/s2
ENG901-1
• The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
3
ENH101-14
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Impact Wrench
Model No./ Type: TW0250
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, MK15 8JD, England
30.1.2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
GEA005-3
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
Produktspezifikationen
| Marke: | Makita |
| Kategorie: | Schraubenmaschine |
| Modell: | TW0250 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Makita TW0250 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schraubenmaschine Makita
5 Oktober 2024
4 Oktober 2024
2 Oktober 2024
24 September 2024
24 September 2024
23 September 2024
22 September 2024
20 September 2024
17 September 2024
15 September 2024
Bedienungsanleitung Schraubenmaschine
- Schraubenmaschine Panasonic
- Schraubenmaschine Cotech
- Schraubenmaschine Bosch
- Schraubenmaschine Laserliner
- Schraubenmaschine Parkside
- Schraubenmaschine Vonroc
- Schraubenmaschine AEG
- Schraubenmaschine Powerfix
- Schraubenmaschine EMOS
- Schraubenmaschine Black And Decker
- Schraubenmaschine Cocraft
- Schraubenmaschine FERM
- Schraubenmaschine Ryobi
- Schraubenmaschine Senco
- Schraubenmaschine Skil
- Schraubenmaschine Hilti
- Schraubenmaschine DeWalt
- Schraubenmaschine Einhell
- Schraubenmaschine Elu
- Schraubenmaschine Festool
- Schraubenmaschine Mafell
- Schraubenmaschine Maktec
- Schraubenmaschine Worx
- Schraubenmaschine Tacklife
- Schraubenmaschine Hikoki
- Schraubenmaschine Hitachi
- Schraubenmaschine Hazet
- Schraubenmaschine Kress
- Schraubenmaschine Metabo
- Schraubenmaschine Stanley
- Schraubenmaschine Güde
- Schraubenmaschine Power Craft
- Schraubenmaschine Meec Tools
- Schraubenmaschine Dremel
- Schraubenmaschine Fieldmann
- Schraubenmaschine Dedra
- Schraubenmaschine Silverline
- Schraubenmaschine Facom
- Schraubenmaschine Greenworks
- Schraubenmaschine Yato
- Schraubenmaschine Genesis
- Schraubenmaschine Pansam
- Schraubenmaschine Toolland
- Schraubenmaschine Batavia
- Schraubenmaschine Matrix
- Schraubenmaschine Milwaukee
- Schraubenmaschine Toolcraft
- Schraubenmaschine Fein
- Schraubenmaschine Omega
- Schraubenmaschine Ingersoll Rand
- Schraubenmaschine Craftsman
- Schraubenmaschine Powerplus
- Schraubenmaschine Alpha Tools
- Schraubenmaschine EasyMaxx
- Schraubenmaschine Ozito
- Schraubenmaschine Kawasaki
- Schraubenmaschine Porter-Cable
- Schraubenmaschine Goon
- Schraubenmaschine Steren
- Schraubenmaschine Meister Craft
- Schraubenmaschine Truper
- Schraubenmaschine Einhell Bavaria
- Schraubenmaschine Wera
- Schraubenmaschine Weidmüller
- Schraubenmaschine Rodcraft
- Schraubenmaschine Cleco
- Schraubenmaschine SW-Stahl
- Schraubenmaschine Gedore
- Schraubenmaschine TAURUS Titanium
Neueste Bedienungsanleitung für -Kategorien-
5 Oktober 2024
4 Oktober 2024
1 Oktober 2024
27 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024