Makita JR3000V Bedienungsanleitung
Makita
Säbelsägen
JR3000V
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Makita JR3000V (32 Seiten) in der Kategorie Säbelsägen. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/32
GB
Recipro saw Instruction Manual
F
Scie recipro Manuel d’Instructions
D
Reciprosäge Betriebsanleitung
I
Seghetto diritto Istruzioni d’Uso
NL
Reciprozaag Gebruiksaanwijzing
E
Sierra alternativa Manual de Instrucciones
P
Serra de sabre Manual de Instruço˜ es
DK
Bajonet sav Brugsanvisning
S
Tigersåg Bruksanvisning
N
Bajonettsag Bruksanvisning
SF
Puukkosaha Käyttöohje
GR ¶·ÏÈÓ‰ÚÔÌÈÎfi ÚÈÔÓÈ √‰ËÁ›Â˜ ÃÚ‹Ûˆ˜
JR3000
JR3000V
1 2
3 4
5 6
7 8
2
ENGLISH Explanation of general view
1Hex wrench
2Bolt
3Shoe
4Bolt
5Speed change switch
6Switch trigger
7Lock button/Lock-off button
8Speed control screw
9High
0Low
qLimit mark
wBrush holder cap
eScrewdriver
SPECIFICATIONS
Model JR3000 JR3000V
Length of stroke .......................................................................... 30 mm 30 mm
Strokes per minute ...................................................................... Hi : 2,500 Low : 1,900 0 – 2,300
Overall length .............................................................................. 400 mm 400 mm
Net weight ................................................................................... 2.9 kg 2.9 kg
•Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
•Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed Safety
instructions.
These symbols mean:
Read instruction manual.
DOUBLE INSULATION
ADDITIONAL SAFETY RULES
1. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
2. Do not cut oversize workpiece.
3. Check for the proper clearance beyond the
workpiece before cutting so that the blade will
not strike the floor, workbench, etc.
4. Hold the machine firmly.
5. Make sure the blade is not contacting the
workpiece before the switch is turned on.
6. Keep hands away from moving parts.
7. When cutting through walls, floors or wher-
ever ‘‘live’’ electrical wires may be encoun-
tered, DO NOT TOUCH ANY METAL PARTS OF
THE MACHINE! Hold the machine by the insu-
lated grasping surfaces to prevent electric
shock if you cut through a ‘‘live’’ wire.
8. Do not leave the machine running. Operate the
machine only when hand-held.
9. Always switch off and wait for the blade to
come to a complete stop before removing the
blade from the workpiece.
10. Do not touch the blade or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing saw blade (Fig. 1)
Important:
Always be sure that the machine is switched off and
unplugged before installing or removing the blade.
First, use the hex wrench to loosen the bolt. With the
blade teeth facing upward or downward, insert the
blade until the hole in the blade shank is just over the
protrusion on the slider. Then tighten the bolt to
secure the blade.
Adjusting shoe (Fig. 2)
Loosen the two bolts holding the shoe. Then slide the
shoe back or forth to the desired position and tighten
the two bolts securely. When the blade loses its
cutting effectiveness in one place, reposition the shoe
to obtain better cutting in another.
Speed change (For JR3000 only) (Fig. 3)
CAUTION:
Use the speed change switch only after the machine
comes to a complete stop.
To change the machine speed, move the speed
change switch to the ‘‘L’’ position for low speed or the
‘‘H’’ position for high speed.
High speed: ordinary wood, plys or plastics
Low speed: metals (steel pipe, sheet metal, stainless
or copper)
Switch action (For JR3000) (Fig. 4)
CAUTION:
Before plugging the machine, always check to see
that the switch trigger actuates properly and returns to
the ‘‘OFF’’ position when released.
3
Produktspezifikationen
| Marke: | Makita |
| Kategorie: | Säbelsägen |
| Modell: | JR3000V |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Makita JR3000V benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Säbelsägen Makita
12 Juli 2024
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
Bedienungsanleitung Säbelsägen
- Säbelsägen Parkside
- Säbelsägen Vonroc
- Säbelsägen AEG
- Säbelsägen Black And Decker
- Säbelsägen FERM
- Säbelsägen Skil
- Säbelsägen Einhell
- Säbelsägen Maktec
- Säbelsägen Hitachi
- Säbelsägen Metabo
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
13 Juli 2024
11 Juli 2024
11 Juli 2024
10 Juli 2024
9 Juli 2024
8 Juli 2024
7 Juli 2024
5 Juli 2024
4 Juli 2024