Makita 3601B Bedienungsanleitung
Makita
Fräsmaschine
3601B
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Makita 3601B (12 Seiten) in der Kategorie Fräsmaschine. Dieser Bedienungsanleitung war für 28 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/12
1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
DOUBLE INSULATION
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Router
3601B
005038
2
ENGLISH (Original instructions)
SPECIFICATIONS
Model 3601B
Collet chuck capacity 12 mm or 1/2"
No load speed (min
-1 ) 23,000 or 26,000 (See Nameplate on the tool)
Overall height 190 mm
Net weight 3.6 kg
Safety class /II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END201-5
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
ï½¥ Read instruction manual.
ï½¥ DOUBLE INSULATION
ï½¥ Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.
ENE010-1
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
ENF002-1
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
ENG102-3
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
pA) : 93 dB(A)
Sound power level (L
WA) : 104 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
ENG223-2
Vibration
The vibration total value (tri-axial vector sum)
determined according to EN60745:
Work mode : cuttig grooves in MDF
Vibration emission (ah) : 3.5 m/s2
Uncertainty (K) : 1.5 m/s2
ENG901-1
• The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH101-13
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Route
r
Model No./ Type: 3601B
are of series production and
Conforms to the following European Directives:
98/37/EC until 28th December 2009 and then with
2006/42/EC from 29th December 2009
And are manufactured in accordance with the following
standards or standardised documents:
3
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd,
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England
30th January 2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
GEA005-3
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
16. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
17. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
Power tool use and care
18. Do not force the power tool. Use the correct
power tool for your application. The correct
Produktspezifikationen
| Marke: | Makita |
| Kategorie: | Fräsmaschine |
| Modell: | 3601B |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Makita 3601B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Fräsmaschine Makita
15 Oktober 2024
31 August 2024
31 August 2024
16 August 2024
4 August 2024
3 August 2024
30 Juli 2024
20 Juli 2024
10 Juli 2024
9 Juli 2024
Bedienungsanleitung Fräsmaschine
- Fräsmaschine Bosch
- Fräsmaschine Flex
- Fräsmaschine Parkside
- Fräsmaschine Vonroc
- Fräsmaschine Black And Decker
- Fräsmaschine FERM
- Fräsmaschine Skil
- Fräsmaschine Topcraft
- Fräsmaschine Alpina
- Fräsmaschine Carat
- Fräsmaschine Eibenstock
- Fräsmaschine DeWalt
- Fräsmaschine Einhell
- Fräsmaschine Festool
- Fräsmaschine Mafell
- Fräsmaschine Maktec
- Fräsmaschine Triton
- Fräsmaschine Worx
- Fräsmaschine Hitachi
- Fräsmaschine Fuxtec
- Fräsmaschine Kinzo
- Fräsmaschine Güde
- Fräsmaschine Power Craft
- Fräsmaschine Meec Tools
- Fräsmaschine Westfalia
- Fräsmaschine DURO
- Fräsmaschine Holzmann
- Fräsmaschine Stomer
- Fräsmaschine Yato
- Fräsmaschine Brüder Mannesmann
- Fräsmaschine AL-KO
- Fräsmaschine Gardena
- Fräsmaschine Powerplus
- Fräsmaschine Rupes
- Fräsmaschine Toledo
- Fräsmaschine Ozito
- Fräsmaschine Texas
- Fräsmaschine Felisatti
- Fräsmaschine Gamma
- Fräsmaschine Grizzly
- Fräsmaschine Protool
- Fräsmaschine Truper
- Fräsmaschine Trend
- Fräsmaschine CMT Orange Tools
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
4 Oktober 2024
20 September 2024
9 September 2024
6 September 2024
6 September 2024
6 September 2024
4 September 2024
4 September 2024
1 September 2024