Makita 194043-3 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Makita 194043-3 (28 Seiten) in der Kategorie Andere. Dieser Bedienungsanleitung war für 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/28
Models:
LS0711B, LS0711Z, LS0713/FL
LS0714/F/FL, LS711D, LS1013/F
LS1030N, LS1040/F, LS1212/F
LS1214/F, LS1220, LS1221, 2012NB
GB Stand
Instruction Manual
F Support
Manuel d’instructions
D Ständer
Betriebsanleitung
I Banco
Istruzioni per l’uso
NL Standaard
Gebruiksaanwijzing
EEstante
Manual de instrucciones
P
Base Manual de instruções
DK
Stand Brugsanvisning
S
Maskinbord Bruksanvisning
N
Stativ Bruksanvisning
SF
Teline Käyttöohje
GR Υποστήριγµα Οδηγίεσ χρήσεωσ
TR Sehpai El kitabı
CH 支架 使用說明書
2
12
34
56
78
14
13
2
12
18
45
45
16
19 17
20
16
17
15
10
13
11
12
14
7
8
3
10
9
6
23
4
5
7
1
3
ENGLISH
Explanation of general view
1Frame
2Bolts
3 Support
4 Inner grooves (A)
5 Outer grooves (B)
6Frame pipe
7 Lock plate
8 Support plate (For LS0714 only)
9 The smallest hole in the support
10 Adjusting bolt
11 Front holes in your tool base
12 Front holes in the supports
13 Bolt
14 Nut
15 Fix plates
16 Outer hole (a)
17 Inner hole (b)
18 The largest holes
19 Outer frame
20 Inner frame
Symbols
WARNING:
• Read and thoroughly understand this manual and the
instruction manual of the tool you use before perform-
ing the following.
• Before installing a tool on this stand, always switch off
and unplug the tool.
• The stand should be bolted in a stable and level sur-
face using the bolts provided on three of four feet.
• This stand can be used only with the models of Miter
saws, Compound miter saw, slide compound miter saw
and thicknesser or planer specified in this manual.
• Open and lock before fastening the tool to the stand.
• Fasten the tool to the supports before use.
• Do not climb, sit or stand on this stand.
• Make sure that the stand is set up so that the corporate
nameplate on the stand always faces the operator.
• Do not carry the stand with the tool.
• Before storing or transporting, fold the frame and
secure the supports by tightening bolts on the support
backside.
How to install the stand
When installing miter saw, compound miter saw and
slide compound saw;
1. Loosen the bolts on the backside of the supports.
(Fig. 1)
2. Open the frame and pivot the supports so that the
frame pipe fits in the inner grooves (A) in the sup-
ports. (Fig. 1)
3. Adjust the position of two supports according to the
distance of front holes in the base of the tool you use.
Push down the lock plate to lock it. (Fig. 1)
Note:
Only when using Model LS0714, install the support
plate so that its holes meet the smallest holes in the
supports and secure it firmly with two bolts. (Fig. 2)
4. Turn the stand so that the adjusting bolt at its foot or
the corporate nameplate faces you. Place the tool in
the middle of the support.
All miter saw models specified in this manual should
be placed so that two front holes of the tool base
match the first front holes on the support. (Fig. 3)
Two rear holes of the tool base meet holes accordingly.
Note: When the holes in the tool base do not align
with those in the support, unlock the lock plate by
raising it, readjust it for fine adjustment and push it
down again to lock it. Secure bolts on the backside
of supports firmly after the adjustment. (Fig. 3)
5. Secure the tool base to the support of the stand with
four hex bolts and four nuts provided with the stand.
Make sure that the two front bolts and nuts have been
firmly tightened in the first front holes in the support.
(Fig. 3)
6. When the stand cannot be set up stable, turn the
adjusting bolt at the foot of stand for proper stability.
After adjustment, make sure that the stand and tool
keep stable. (Fig. 4)
7. Secure the feet of stand to the stable and level sur-
face using holes in the fix plates with three hex bolts.
(Fig. 4)
When installing thicknesser or planer
CAUTION:
When using the thicknesser or planer specified in
this manual, set up the stand in the low position
mode.
Failure to do so may result in fall-down and personal
injury.
1. See (1) and (2) stated above in the titled “When
installing miter saw”.
2. Loosen and remove the bolt and nut that secure the
lock plate and outer frame. Change the installation
position of the lock plate from the outer hole (a) to the
inner hole (b) and retighten the bolt firmly. Repeat the
same action on another side. (Fig. 5)
3. Close the frame slightly, raise the support and detach
the frame pipe from the inner grooves (A) in the sup-
port. While holding the frame on, widen the feet of
frame carefully and fully. Fit the frame pipe in the
outer grooves (B) in the support. (Fig. 6)
4. Adjust the position of the supports according to the
distance of front holes in the base of the tool you use.
Push down the lock plate to lock it. (Fig. 7)
5. Turn the stand so that the adjusting bolt at its foot or
the corporate nameplate faces you. Place the tool in
the middle of the support. Thicknesser or planer
model specified in this manual should be placed so
that four holes of the tool base match the largest
holes on the support of the stand. (Fig. 7)
Note: When the holes in the tool base do not align
with those in the support, unlock the lock plate by
raising it, readjust it for fine adjustment and push it
down again to lock it. Secure bolts on the backside
of supports firmly after the adjustment. (Fig. 7)
6. Secure the tool base to the support of the stand with
four hex bolts and four nuts provided with the stand.
Make sure that these four bolts are inserted from the
underside as shown in the figure. (Fig. 8)
7. The subsequent actions are the same as (6) – (7) in
the “When installing miter saw, compound miter saw
and slide compound saw;”.
❏Read instruction manual.
❏Maximum allowable loading.
MAX
100Kg
(220lbs.)
Produktspezifikationen
| Marke: | Makita |
| Kategorie: | Andere |
| Modell: | 194043-3 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Makita 194043-3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Andere Makita
9 Juli 2024
9 Juli 2024
9 Juli 2024
9 Juli 2024
9 Juli 2024
9 Juli 2024
9 Juli 2024
9 Juli 2024
9 Juli 2024
9 Juli 2024
Bedienungsanleitung Andere
- Andere Brennenstuhl
- Andere Oregon
- Andere Voltcraft
- Andere Bosch
- Andere Flex
- Andere Laserliner
- Andere Parkside
- Andere Vonroc
- Andere AEG
- Andere Powerfix
- Andere Bostitch
- Andere FERM
- Andere Ryobi
- Andere Skil
- Andere Topcraft
- Andere Ideen Welt
- Andere Alpina
- Andere Bort
- Andere DeWalt
- Andere Einhell
- Andere Festool
- Andere Triton
- Andere Worx
- Andere Tronic
- Andere Hikoki
- Andere Hyundai
- Andere Fuxtec
- Andere Max
- Andere Stanley
- Andere Wagner
- Andere Kärcher
- Andere Lotus
- Andere Atika
- Andere Scheppach
- Andere Probuilder
- Andere Workzone
- Andere Gloria
- Andere Dremel
- Andere Proxxon
- Andere Husqvarna
- Andere Stihl
- Andere DURO
- Andere Rawlink
- Andere Holzmann
- Andere MSW
- Andere Airpress
- Andere Huvema
- Andere Stomer
- Andere BluCave
- Andere Brandson
- Andere Altrex
- Andere Kyoritsu
- Andere Batavia
- Andere Dolmar
- Andere Brüder Mannesmann
- Andere Milwaukee
- Andere Fein
- Andere Omega
- Andere AL-KO
- Andere Wolf Garten
- Andere Powerplus
- Andere Rupes
- Andere EasyMaxx
- Andere VARO
- Andere DAP
- Andere Datona
- Andere Digi
- Andere Dollken-Weimar
- Andere Dunlop
- Andere Emco
- Andere Ergofix
- Andere Ferrex
- Andere Gamma
- Andere Grizzly
- Andere Gude Pro
- Andere Heidenhain
- Andere Hofmann
- Andere Komatsu
- Andere Kompernass
- Andere Kraft
- Andere Mac Allister
- Andere Max Bahr
- Andere Maxicool
- Andere NDS
- Andere Numatic
- Andere OKAY
- Andere PLS - Fluke
- Andere Powerfix Profi
- Andere Renovator
- Andere Sievert
- Andere Sola
- Andere Spero
- Andere Tecomec
- Andere Turbotech
- Andere Turbotronic
- Andere Xenteq
- Andere Zodiac
- Andere Black Decker
- Andere Bartec
- Andere Ateq
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
15 Oktober 2024
27 September 2024
27 September 2024
23 September 2024
23 September 2024
23 September 2024
20 September 2024
17 September 2024
16 September 2024