LYYT LT24560-RGBW Bedienungsanleitung

LYYT Nicht kategorisiert LT24560-RGBW

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für LYYT LT24560-RGBW (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
www.avsl.com 156.772UK User Manual
24V LED Tape 5m - RGBW 60/m
User Manual
Introduction
Super-bright IP65 rated RGBW LED tape which when connected to a controller can produce
any colour of the rainbow. Supplied on 5m reel with an adhesive back this tape is easy to
setup and quick to install. Its 24Vdc supply and low power consumption makes it suitable for
a wide variety of applications from homes to vehicles and from shops to bars and nightclubs.
The LEDs will last up to 50,000 hours and are covered with an epoxy coating to protect the
tape from general wear and tear as well as being water resistant, making cleaning an easy
task.
Specification
Voltage
24Vdc
Beam angle
180°
Light intensity per LED
1800-2000mcd
LED Type
Sanan SMD5050
Reel Length
5m
IP Rating
IP65
Power consumption per metre
16W
LED quantity per metre
60
LED spacing
12mm
Cut points
10cm
Colour rendering index
>80
Current
670mA per metre
Cross-section
12 x 4mm
Weight
126kg
Installation of this LED tape should be carried out by competent electrical installers, observing the
relevant electrical safety procedures.
Lyyt RGBW LED tape has a self-adhesive backing to allow it to be easily attached to a clean, non-porous
surface.
www.avsl.com 156.772UK User Ma al nu
Where less than 5m of tape is needed, there are solder points as shown below, where the tape may be
cut to size. These cut points are at 10cm intervals. -connect to another length of tape after To re
cutting, strip away the epoxy coating at the solder points and solder a wire from V+, G B and W to , R,
corresponding points on the next length of tape. Some accessories are supplied with the tape reel for
this purpose. retain weatherproofing, it is advised to seal the cuts and joints with silicone glue.To
Each 5m reel of RGBW LED tape is fitted with a 5-pin connector for power input from an RGBW
controller. Ensure that the V+, G B and W pins are connected the correct way round. 24V tape can , R,
be installed in 10m lengths between repeater/amp fiers by using the included 5-pin couplers to li
connect 2 reels together in sequence. The amplifier repeater ensures that extension reels mimic the
colour changes of the original reel as dictated by the controller.
It is imperative that the power supply, controller, and amplifier/repeater should have higher than the
rated capacity in Amps (A) for the current required to power the length(s) of LED tape installed. Please
see the table below for reference.
Tape Length
5m
10m
Current for 24V RGBW tape
60 LED/m
3.35A
6.7A
Please visit www.avsl.com to select from our range of 24Vdc power supplies, RGBW controllers and
RGBW amplifier/repeaters that are suitable for powering Lyyt RGBW LED tapes
This p d t is classed as Electrical or Electronic equipment and should not disposed with other household or ro uc be
commercial waste at the end of its useful life. The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright© 22 AVSL Group Ltd Unit 2 Bridgewater Park, AVSL (Europe) Ltd, Unit 3D North Point Hou 20 , se,
Taylor Road, Trafford Park, Manchester. M 7JQ. North Point Bus. Park, New Mallow Road, Cork, Ireland. 41


Produktspezifikationen

Marke: LYYT
Kategorie: Nicht kategorisiert
Modell: LT24560-RGBW

Brauchst du Hilfe?

Wenn Sie Hilfe mit LYYT LT24560-RGBW benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert LYYT

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-