LYYT DIY-DW120 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für LYYT DIY-DW120 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
DIY LED TAPE KIT CW/WW –
153.739UK User Manual
DIY LED TAPE KIT 5m Cool white & Warm White –
Introduction:
Thank you for purchasing the Lyyt DIY CW/WW LED Tape. LED tape is ideal for use on the underside of a counter tops, shelves, cupboards,
around window frames or in an alcove of a ceiling to name just a few examples.
Before starting please ensure that you have read this instruction leaflet carefully.
If you are unsure about anything please have the tape installed by a competent installer.
Contents:
1 x 5m reel of CW/WW LED tape
1 x UK power adaptor
1 x Control Box with IR remote handset
Possible required tools: Scissors, Craft knife, Soldering iron and solder, 4 core DC wire and heat shrink tube.
Step 1: Preparation
Ensure the surface you are attaching to is clear of dust and dirt. Clean thoroughly and leave to dry before fitting the tape.
Step 2: Connecting IR Controller:
Connect the 4pin connector to the control box and then to the LED tape (FIG 1). Plug in the power supply and use the IR remote control to select
the various functions (Fig 2).
Unravel the tape to check that all the LEDs are functioning correctly. If there are any faults return to your retailer without delay.
FIG 1:
FIG 2:
IR remote function
The remote control has altogether 16 different colour temperatures to choose from, with other function keys as shown below:
* Fade mode: Press once for fade on both colours. Press twice for fade on cool white. Press 3 times for fade on warm whi . te
153.739UK User Manual
Step 2: Cutting
WARNING: Disconnect from the power supply before attempting any cutting.
Measure out each section and cut with sharp scissors only at the marked 10cm intervals. Do not discard any excess tape as it can be easily
reconnected and used again (see FIG 4).
Step 3: Fitting:
Clear the area you wish to install and remove the backing paper, exposing the adhesive tape. Push tape firmly onto the surface. It is recommended
to work on 50cm sections at a time in order to ensure a professional finish. When you reach the end of your installation cut at the marked cutting
point. The tape can be terminated at highlighted 10cm cut intervals if less than 5m is required.
FIG 3:
You may also reconnect the two pieces by soldering the point connections together. The tape has 3 tracks for the DC voltage:
To re-attached use a craft knife to cut the Epoxy coating from the terminals.
Use a soldering iron and solder to connect the DC wire to the relative terminals be sure not to cause a short circuit in the process as it will not
work.
FIG4:
WARNING: Only cut the tape on the highlighted intervals. Cutting the tape in other parts without due care will permanently damage that section of
the tape and will result in malfunction.
Points to remember when using this tape
1) Only cut the tape at the highlighted 10cm intervals.
2) Do not connect another reel and operate from a single power supply as this will seriously affect the performance.
3) Ensure you connect the correct wires otherwise the tape will not work.
4) Ensure that there are no short circuits when solderin g.
5) We recommend use heat shrink to protect the connection. of tubes
6) Check that everything operates correctly before installing.
FAQ:
Q) Can you cut a 5m tape in many of different sections then solder connect them all together?
A) Yes as long as you cut the tape at 10cm intervals highlighted.
Q) Can I connect the tape together to form a loop?
A) Yes you can as long as both sides have a sufficient power supply it is possible.
Q) Can I use the tape outdoors?
A) Yes the tape is IP65 rated. Ensure though that the terminated ends are heat shrink protected.
Q) Can I use the LED tape without a controller?
A) Yes you can but you can only have a choice cool white and/or warm white. It would be better to buy single colour tape. of
Specifications
Voltage
12Vdc
Current consumption
300mA/m
Power consumption
3.6W/m
Number of LEDs
60/m
LED Spacing
16mm
Cut intervals
10cm
Beam angle
120°
LED type
SMD3528
IP rating
IP65
Errors and omissions excepted.
Copyright© 2017 AVSL Group Ltd.


Produktspezifikationen

Marke: LYYT
Kategorie: Nicht kategorisiert
Modell: DIY-DW120

Brauchst du Hilfe?

Wenn Sie Hilfe mit LYYT DIY-DW120 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert LYYT

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-