Lynx Professional LCB2-3 Bedienungsanleitung

Lynx Nicht kategorisiert Professional LCB2-3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lynx Professional LCB2-3 (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
LCB2-3 INSTALLATION INSTRUCTIONS
TOOLS REQUIRED: 7/16 Wrench
CONTENTS OF KIT: An adjustable side burner mounting bracket
Side shelf mounting bracket with 7/16 fasteners
Decorative cover for the L27 and L36 models
The side burner support bracket comes preassembled for the L27 and L36
Lynx Grills, 7300 Flores St., Downey, CA 90242
Customer Care Ph.: 888 5969/ Fax: 562 6978/Service@lynxgrills.com -289- -299-
P/N 34912 8/14
INSTRUCTIONS FOR MODELS L36 and L27:
1. Remove the right hand side shelf and the cabinet back panel (fig. 1)
2. Mount the LCB2 -3 side burner to the supports (fig. 2)
3. If needed, any misalignment can be corrected by 1st measuring the amount of misalignment, 2nd loosening the
bracket support fasteners. 3rd raise or lower the bracket according to your measurements.
Tighten the fasteners. (fig 3)
4. Hang the side shelf removed in step 1 on the right side shelf support pins of the side burner (Fig. 6, pg. 2)
P/N 34912. 8/14
Rear View
1 2
3
INSTRUCTIONS FOR MODELS L54, L42, L30:
1. Remove the right hand side shelf. See fig.1 on page 1
2. At the rear, remove the decorative cover (1) on the left hand side of the LCB2 3 by removing the Philips head screw -
and sliding it out. This also gives access to the gas piping connections. (Fig. 2)
3. Locate the mounting bracket on the inner most bracket support (Fig 3). Remove the 7/16 fasteners holding it in
place Reinstall the mounting bracket on the rear most bracket support and secure it with the 7/16 fasteners
4. As in step 3 on page 1,correct any misalignment in the shelf
5. Move the shelf mounting bracket on the right hand side, to the outermost mounting holes using the 7/16 nuts, and
tighten. (Fig. 5)
6. Hang the side shelf removed in step 1, pg. 1 to the right side of side burner on the shelf mounting bracket pins
(Fig 6)
2
Remove the bracket from the inside
support and install it onto the outer
support
3
5
This bracket must be mounted in the outer
position
6
Once the side burner is mounted to the grill the gas con-
nections can be made. Refer to the illustrations on the
right for proper gas installation examples.
After the side burner gas connections are made it is rec-
ommended that a leak test be done on all gas line fittings.
Apply a soap and water solution to all connections and
look for bubbles to form which indicate a gas leak. If no
bubbles are present, make the electrical connections
The side burner is electrically connected to grill at the
transformer. Disconnect the transformer from the grill
and plug in the side burner as shown in the illustration
below.
Finished Dimensions


Produktspezifikationen

Marke: Lynx
Kategorie: Nicht kategorisiert
Modell: Professional LCB2-3

Brauchst du Hilfe?

Wenn Sie Hilfe mit Lynx Professional LCB2-3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Lynx

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-