Lowrance EP-90R Pressure Bedienungsanleitung

Lowrance Nicht kategorisiert EP-90R Pressure

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lowrance EP-90R Pressure (32 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 63 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/32
1
Pub. 988-0154-641
EP-90R Pressure
Electronic Sensor
Installation and Configuration Instructions
This document shows how to install an EP-90R Pressure sensor and
how to connect it to a NMEA 2000® network. It also provides
instructions on how to configure your pressure sensor with Lowrance
digital gauges (LMF-200 & LMF-400) and display units.
NMEA 2000 is the communication bus standard developed by the
National Marine Electronics Association (NMEA) for use in boats.
Lowrance has introduced a line of products that can communicate over
a NMEA 2000 network (LowranceNet).
All Lowrance NMEA 2000 capable devices are either NMEA 2000
certified or certification is pending.
CAUTION:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. Decide where you want to install
all components before drilling any holes in your vessel.
Some sonar or GPS display units may require a software upgrade to
display NMEA 2000 data correctly. For free software upgrades or
additional information on the LowranceNet NMEA 2000 ® network
system, visit our web site, www.lowrance.com.
EP-90R Pressure Sensor.
Hose barb
attachment
Red NMEA 2000
connector
2
The EP-90R consists of a red cable connector and the EP-90R housing
with standard size hose barb attachment.
The EP-90R Water Pressure sensor, like the other LowranceNet
Electronic Probe (EP) sensors, is designed for use with a NMEA 2000
DeviceNet Network. Your sensor, however, is also compatible with
LowranceNet blue connector networks. It can be added to a blue
connector network by using a red female to blue female adapter cable.
Your sensor MUST be connected to a NMEA 2000 network or it WILL
NOT function.
The NMEA 2000 red female to blue female adapter cable allows users
to add red connector devices to a blue connector network.
Tools and Supplies
Your EP sensor packs with a T connector needed to attach it to a
LowranceNET NMEA 2000 network. If this is the first sensor you are
connecting, you may also need a one-time purchase of a LowranceNET
Node Kit.
The following tools and supplies are NOT included. Required tools
include: a utility knife. For some installations, a Phillips screwdriver
will be needed. Supplies include: zip/cable tie.
LowranceNET Node Kit for a NMEA 2000 network. Includes a 2-foot
extension cable, T connector and two 120-ohm terminators.
3
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one, see the other document packed with your
EP-90R, "Setup and Installation of NMEA 2000 Networks, General
Information" part number 988-0154-173. If that document is not
available, it can be downloaded free from the Lowrance web site.
Installation
The EP-90R Pressure sensor can provide pressure data for the
following categories: Atmospheric Pressure, Engine Boost Pressure,
Engine Oil Pressure, Engine Water Pressure, Fuel Pressure,
Transmission Oil Pressure and Pitot Speed.
WARNING:
The maximum pressure for an EP-90R Pressure sensor is
100 PSI (689 kPa). If that pressure level is exceeded you
not only risk damaging the EP-90R, but could also suffer
bodily injury.
Pitot Tube (Water Speed)
We recommend installing the EP-90R near the boat’s original
speedometer.
NOTE:
If your engine does not have a speedometer hose, you will have to
purchase a pitot tube kit to use the EP-90R Pressure sensor. For
pitot tube installation instructions, refer to your pitot tube
installation manual.
The following steps cover the recommended installation of the EP-90R.
You will attach the EP-90R to a pitot tube hose in the same manner.
1. Remove the pressure hose from the boat’s speedometer.
2. Clip off the end of the pressure hose that was connected to the
speedometer. This will help ensure the pressure hose will fit snugly on
the EP-90R hose barb attachment. The hose-barb attachment
requires a 1.4" (6.35 mm) hose.
1/4 " hose barb attachment


Produktspezifikationen

Marke: Lowrance
Kategorie: Nicht kategorisiert
Modell: EP-90R Pressure

Brauchst du Hilfe?

Wenn Sie Hilfe mit Lowrance EP-90R Pressure benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Lowrance

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-