Lowrance EP-65R Fluid Level Bedienungsanleitung

Lowrance Nicht kategorisiert EP-65R Fluid Level

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lowrance EP-65R Fluid Level (52 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/52
1
Pub. 988-0154-372
EP-65R Fluid Level
Electronic Sensor
Installation, Configuration and Calibration Instructions
This document shows how to install an EP-65R Fluid Level sensor and
how to connect it to a NMEA 2000® network. It also provides
instructions on how to configure and calibrate your fluid level sensor
with Lowrance digital gauges (LMF-200 & LMF-400) and display units.
NMEA 2000 is the communication bus standard developed by the
National Marine Electronics Association (NMEA) for use in boats.
Lowrance has introduced the LowranceNetâ„¢, a line of products that
can communicate over a NMEA 2000 network.
All Lowrance NMEA 2000 capable devices are either NMEA 2000
certified or certification is pending.
Caution:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. Decide where to install all
components before drilling any holes in your vessel.
Some sonar or GPS display units may require a software upgrade to
display NMEA 2000 data correctly. For free software upgrades or
additional information on the LowranceNet NMEA 2000 ® network
system, visit our web site, www.lowrance.com.
The EP-65R Fluid Level sensor.
NMEA 2000 red
cable connector
Smart
module
Sending unit
connections
red lead and
black lead.
2
The EP-65R consists of a smart module with a red cable connector on
one end and two bare wires on the other. The cable length from the
connector to the smart module is 18 inches (46 cm). The cable length
from the smart module to the bare wires is 10 feet (3 meters).
The smart module converts fluid level information received from the
sending unit (fluid level float) to the NMEA 2000 data format. This
allows any digital gauge, sonar or GPS unit connected to the NMEA
2000 network to display fluid level information.
The EP-65R fluid level sensor is designed to monitor fuel, live well, oil,
fresh water, waste water (gray water), and black water tanks.
The EP-65R Fluid Level, like the other LowranceNet Electronic Probe
(EP) sensors, is designed for use with a NMEA 2000 network. Your
sensor, however, is also compatible with LowranceNet blue connector
networks. It can be added to a blue connector network by using a red
female to blue female adapter cable. Your sensor MUST be connected
to a NMEA 2000 network or it WILL NOT function.
The NMEA 2000 red female to blue female adapter cable allows users
to add red connector devices to a blue connector network.
Tools and Supplies
Your EP sensor packs with a T connector needed to attach it to a
LowranceNET NMEA 2000 network. If you are connecting to an
existing LowranceNET network, those are all the electronic
components you need. If this is the first sensor you are connecting, you
will need to purchase a LowranceNET Node Kit.
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one, refer to the "Setup and Installation of
NMEA 2000 Networks, General Information" document (part number
988-0154-173) included with your EP-65R sensor. If that document is
missing it can be downloaded free from the Lowrance web site.
3
LowranceNET Node Kit for a NMEA 2000 network. Includes a 2-foot
extension cable, T connector and two 120-ohm terminators.
Sending unit mounting plate configurations vary. When connecting the
EP-65R, you will need whatever tools and supplies that will work with
your sending unit's specific design. Recommended tools include: wire
pliers. You will need a drill and a 7/8" (22 mm) drill bit. If you need to
route the smart module or cable connector through a bulkhead, you will
need a drill and a 7/8" (22 mm) drill bit.
Supplies are not included, unless otherwise indicated. The EP-65R's two
lead wires are pre-stripped. We recommend using marine-grade crimp-on
connectors that will fit your sending unit's electrical connections.
Tip:
The EP-65R is designed to be the only device receiving signals from
the sending unit. If the EP-65R is replacing a previous gauge, make
sure you remove all the old gauge wires before you begin. If this is a
replacement, note which connection is positive before disconnecting
the old wires.
Installation
This instruction sheet assumes the mounting bracket is connected to
the fluid level float (or potentiometer) and is already installed in the
tank. The EP-65R wires — red (positive) and black (negative) — will
connect to the sending unit's mounting bracket on top of the tank.
Caution:
Do NOT connect the sensor's red cable connector to the network
until you have finished connecting the red and black leads to the
sending unit. This reduces the risk of a spark when working
around fuel tanks.
First, attach marine-grade crimp-on connectors to both the red lead (+)
and the black (–) lead. The EP-65R must be the ONLY device
connected to the sender.


Produktspezifikationen

Marke: Lowrance
Kategorie: Nicht kategorisiert
Modell: EP-65R Fluid Level

Brauchst du Hilfe?

Wenn Sie Hilfe mit Lowrance EP-65R Fluid Level benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Lowrance

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-