Lowrance EP-60R Fuel Flow Bedienungsanleitung

Lowrance Nicht kategorisiert EP-60R Fuel Flow

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lowrance EP-60R Fuel Flow (48 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/48
1
Pub. 988-0154-432
EP-60R Fuel Flow
Electronic Sensor
Installation, Configuration and Calibration Instructions
This document shows how to install an EP-60R Fuel Flow sensor and
how to connect it to a NMEA 2000® network. It also provides
instructions on how to configure and calibrate your fuel flow sensor
with Lowrance digital gauges (LMF-200 & LMF-400) and display units.
NMEA 2000 is the communication bus standard developed by the
National Marine Electronics Association (NMEA) for use in boats.
Lowrance has introduced a line of products that can communicate over
a NMEA 2000 network (LowranceNet).
All Lowrance NMEA 2000 capable devices are either NMEA 2000
certified or certification is pending.
Caution:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. You should decide where to
install all components before drilling any holes in your vessel.
The EP-60R Fuel Flow sensor.
NMEA 2000
red connector
Fuel Flow
module
2
Some sonar or GPS display units may require a software upgrade to
display NMEA 2000 data correctly. For free software upgrades or
additional information on the LowranceNet NMEA 2000® network
system, visit our web site, www.lowrance.com.
The EP-60R consists of a red cable connector and the sensor module.
The sensor module contains a turbine to measure fuel flow and
electronics which convert flow data to the NMEA 2000 data format.
The cable length from the connector to the smart module is 10 feet (3
meters). The sensor is designed to work with gasoline only.
WARNING:
Do not use this sensor with diesel engine fuel systems.
The EP-60R is designed only for gasoline engines.
This sensor has been optimized to measure flow rates between 0.6 to 45
gallons (US) per hour, but it will operate at flow rates outside that
range. The sensor will add 0.5 PSI of back pressure on the fuel system
with a flow rate of 20 gallons per hour. At the rate of 40 gallons per
hour, the back pressure will be 1 PSI.
The EP-60R Fuel Flow, like the other LowranceNet Electronic Probe
(EP) sensors, is designed for use with a NMEA 2000 network. Your
sensor, however, is also compatible with LowranceNet blue connector
networks. It can be added to a blue connector network by using a
female red to female blue adapter cable. Your sensor MUST be
connected to a NMEA 2000 network or it WILL NOT function.
The NMEA 2000 female red to female Blue adapter cable allows users
to add red connector devices to a blue connector network.
Tools and Supplies
Your EP sensor packs with a T connector needed to attach it to a
LowranceNET NMEA 2000 network. If this is the first sensor you are
connecting, you may also need to purchase of a LowranceNET Node
Kit.
3
LowranceNET Node Kit for a NMEA 2000 network. Includes a 2-foot
extension cable, T connector and two 120-ohm terminators.
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one, see the other document packed with your
EP-60R Fuel Flow, "Setup and Installation of NMEA 2000 Networks,
General Information" part number 988-0154-173. If that document is
unavailable, it can be downloaded free from the Lowrance web site.
Other supplies are not included, unless otherwise indicated. Required
supplies include cable ties or other fasteners to secure the hose and
cable; an inline fuel filter and any items needed to install it. Two 1"
hose clamps are included with the sensor.
We assume you already have a fuel line installed. The EP-60R Fuel
Flow was designed to fit a typical 3/8" SAE USCG Type A1 fuel hose. If
your engine has different diameter hoses or metal fuel lines, a section
of 3/8" fuel line must be installed between the sensor and the existing
lines. Recommended tools are a flathead screwdriver to tighten the
clamps and a knife to cut the fuel hose. If you need to route the sensor
connector through a bulkhead, you will need a drill and a 3/4" drill bit.
Installation
Install one EP-60R sensor per engine. If you have multiple tanks, place
the sensor after any Y or T in the line feeding the engine.
The sensor should be installed vertically, as close as possible to the fuel
tank in an area where vibration is minimized. The housing has a
molded-in, fuel flow direction arrow, which should be pointing up.
Mount the sensor above the tank's maximum fuel level to avoid
accidental fuel leakage in case the sensor becomes disconnected.
Caution:
Gasoline is extremely flammable. If possible, drain the fuel line
before you start or shut any flow valves located at the tank. Keep
sparks and flame away from the work area. After installation,
remember to clean up any spilled fuel.


Produktspezifikationen

Marke: Lowrance
Kategorie: Nicht kategorisiert
Modell: EP-60R Fuel Flow

Brauchst du Hilfe?

Wenn Sie Hilfe mit Lowrance EP-60R Fuel Flow benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Lowrance

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-