Lowrance EP-10 Fuel Flow Bedienungsanleitung

Lowrance Nicht kategorisiert EP-10 Fuel Flow

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lowrance EP-10 Fuel Flow (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
1
`Pub. 988-0154-431
EP-10 Fuel Flow
Electronic Sensor
Installation Instructions
This instruction manual explains how to install your EP-10 fuel flow
sensor and connect it to a NMEA 2000 network using LowranceNET
network components. You must refer to your digital gauge, sonar or
GPS unit's manual for sensor operation instructions.
Caution:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. You should decide where to
install all components before drilling any holes in your vessel.
Some sonar or GPS units may require a software upgrade to display
NMEA 2000 data correctly and a manual addendum describing how to
operate the sensor. You can download these free and get additional
information on the NMEA 2000 compatible LowranceNET system at
our web site, .www.lowrance.com
WARNING:
Do not use this sensor with diesel engine fuel systems.
The EP-10 is designed only for gasoline engines. Please
see fuel filter warning on page 4 for additional
information.
The EP-10 Fuel Flow sensor.
Blue female NMEA
2000 connector
Sensor
module
2
All Lowrance NMEA 2000 capable devices are NMEA 2000 certified or
certification is pending. See our web site for the latest product status
information.
The EP-10 consists of a blue female locking cable connector and the
sensor module. The sensor module contains a turbine to measure fuel
flow and electronics which convert flow data to the NMEA 2000 data
format. The cable length from the connector to the smart module is 10
feet. The EP-10 sensor is designed to work with engines only.gasoline
This sensor has been optimized to measure flow rates between 0.6 to 45
gallons (U.S.) per hour, but it will operate at flow rates outside that
range. The sensor will add 0.5 PSI of back pressure on the fuel system
with a flow rate of 20 gallons per hour. At the rate of 40 gallons per
hour the back pressure will be 1 PSI.
The EP-10, like other Lowrance Electronic Probe (EP) sensors, is
designed only for use with a NMEA 2000 Network. It bemust
connected to a NMEA 2000 network or it function.will not
Tools and Supplies
Your EP-10 sensor comes with a T connector. The T connector is needed
to attach the sensor to a LowranceNET NMEA 2000 network. If you are
connecting to an existing LowranceNET network, those are all the
electronic components you need. If this is the first sensor you are
connecting, you also will need a one-time purchase of a LowranceNET
Node Kit.
LowranceNET Node Kit for a NMEA 2000 network. Includes a 2 foot
extension cable, T connector, 120-ohm male terminator and 120-ohm
female terminator.
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one refer to the "Setup and Installation of NMEA
2000 Networks, General Information" document (part number 988-
3
0154-172) included with your EP-10 sensor. If that document is missing
it can be downloaded free from the Lowrance web site.
Other supplies are not included unless otherwise indicated. Required
supplies include cable ties or other fasteners to secure the hose and
cable; an in-line fuel filter and any items needed to install the filter.
Two 1" hose clamps are included with the sensor.
We assume you already have a fuel line installed. The EP-10 was
designed to fit a typical 3/8" (9.5 mm) SAE USCG Type A1 fuel hose. If
your engine has different diameter hoses or metal fuel lines a section of
3/8" fuel line must be installed between the sensor and the existing
lines.
Recommended tools are a flathead screwdriver to tighten the clamps
and a knife to cut the fuel hose. If you need to route the sensor
connector through a bulkhead you will need a drill and a 3/4" drill bit.
Installation
Install one EP-10 sensor per engine. If you have multiple tanks, place
the sensor after any Y or T in the line feeding the engine.
The sensor should be installed vertically and as close as possible to the
fuel tank in an area where vibration is minimized. The housing has a
molded-in fuel flow direction arrow which should be pointing up. (See
the figures on the following page.)
Mount the sensor above the tank's maximum fuel level to avoid
accidental fuel leakage in case the sensor becomes disconnected.
Caution:
Gasoline is extremely flammable. If possible, drain the fuel line
before you start or shut any flow valves located at the tank. Keep
sparks and flame away from the work area. After installation
remember to clean up any spilled fuel.
Cut the fuel hose where you intend to install the EP-10 sensor. Slide a
clamp over the hose coming from the tank and push the hose onto the
bottom hose barb.(inlet)
Seat the hose flush against the sensor housing and tighten the hose
clamp. Attach the hose leading the engine on the top to (outlet) barb in
the same way.


Produktspezifikationen

Marke: Lowrance
Kategorie: Nicht kategorisiert
Modell: EP-10 Fuel Flow

Brauchst du Hilfe?

Wenn Sie Hilfe mit Lowrance EP-10 Fuel Flow benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Lowrance

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-