LogiLink AVM365 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für LogiLink AVM365 (4 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
1. Paste the installation sticker
supplied with this camera to
where to install the camera,
and position the four holes for
screws.
Drill the two screws at top to
the wall. ( and as shown
in the picture )
454Z
m565_365a_V1.0
2Prerequisite
Prerequisite (continued)
Before configuring network setup with iPhone / iPad, make
sure you have checked the followings:
(Recommended) Apply your own ADSL or cable
Internet service to simplify the network configurations.
Your camera is connected to your wireless router with
a RJ45 network cable, and it’s powered on.
You have installed our mobile program,
EagleEyes-Lite EagleEyes-Plus or , on your iPhone or
iPad.
iPhone / iPad
Network
Cable
(RJ45)
Wireless
Router
Modem
Camera
LAN Port WAN Port
Event Trigger
System Install the Camera
1
2. 161
Step4: Select “Apply” to confirm all your changes, and you see the message “Done” or “Fail” in “Status”.WAIT till
Done
Fail
Step6: Open your web browser on iPhone, and enter the IP address of your wireless router (“ ” in 192.168.2.161
our example) to access.
Step3: Select the IP address to enter the setting page, and switch the tab from “DHCP” to “Static”.
Then, note down the IP address and port number you see here. You’ll need them in Step 7.
Step5: In the new device page, give a meaningful name for this connection in “Title”, and select “Save”.
3Configure with iPhone / iPad
Step1: Connect your iPhone / iPad to the wireless router
which has the camera connected.
iPhone / iPad
Network
Cable
(RJ45)
Wireless
Router
Modem
Camera
LAN Port WAN Port
Step2: Open “EagleEyes-Lite” (or “EagleEyes-Plus”),
and click “+” to enter the new device page.
Then, select “Local Network Search” to search
your network camera.
The IP address shown is the address assigned to
your camera by your router.
1
B
A
A
B
You have checked the IP address used by your wireless
router as instructed below, and written them down.
You will need them later.
Connect your iPhone / iPad to the wireless router
with the camera connected, and go to “Settings”
“Wi-Fi”. Select “>” near the selected wireless network
to enter the details.
(Optional) Your wireless router supports UPnP, and
this function is enabled.
2
1
Note: Please leave some space between the
screws and wall. Do not get them to the end.
2. Hang the camera at the
screws you just fixed, and
make sure the camera
stays in place. Decide the
cable direction (up
/ down) before you fasten
the screws tight to the wall.
A
B
2
A
B
3. Drill the rest of screws ( and as shown in the
picture ) into the wall. After that, make sure all
screws are fastened.
3
C
D
C
D
3
4
4. Adjust the angle of the camera (up / down / left /
right) with the supplied wrenches for better viewing.
a.b.
Q1: I can’t connect to this camera with 3G network, but it works with my wireless network. Why?
A1: Your network configuration is not yet completed. Please set port forwarding as instructed in “3. Configure with iPhone /
iPad” (Step7 ~ 8).
Q2: My live images are not fluent. Why?
A2: Image fluency could be affected by the local network upload bandwidth, router efficiency, client network download
bandwidth, complexity of live view, and more.
(Recommended) To have the best image fluency, select QVGA; to have the best image quality, select “SXGA”; to have
normal image fluency and quality, select “VGA”.
Q&AEagleEyes Operation
4Check Your Connection
Tool Bar
Setting
Info
The first two buttons from the left are used for the address book, and the other two are special buttons.
Select to learn more about how to use EagleEyes, where to find video demo, and join our Facebook.
Configures EagleEyes-related parameters.
Configuration Select to enter the camera configuration page to change some camera parameters.
Start to enter :EagleEyes Address Book
Select the connection set to enter :Live View & Control
When you complete the network setup, check your
connection as instructed below.
Step1: Switch your network mode to 3G mode on
iPhone or iPad.
Step2: Start , and select the connection you EagleEyes
just added to see if you can access your
camera successfully.
Step3: Switch your network mode to wireless mode on
iPhone or iPad.
Step4: Start , and add a new connection with EagleEyes
the IP address (e.g. 192.168.2.161) and port
number (e.g. 88) you set in Step3 of “3. Configure
with iPhone / iPad”. Then, see if you can access
your camera with this new conection successfully.
5Change Default Account
To ensure your account safety, after finishing
network setup, please access the camera, and
select “ “Advance Setup” Account” to
change the default user name and password with
new one you prefer.
Q3: The live video keeps flickering. Why?
A3: Please try adjusting the power line frequency to “60 Hz” or “50 Hz” from your iPhone by selecting “ ” to enter IPCAM
Configuration page. Then, go to “Advance Setup” “Camera” to change setting.
POE Connection (1.3 mega model only)
POE connection is available only when your router or
hub supports this function.
If your router or hub doesn’t support POE connection, you
need to additionally purchase a POE connector. Please
check with your installer or reseller for more details.
POE Router / Hub
Power
PC
Network
Cable
Network
Cable
Factory Default Values
admin
admin
IP Address
Port Number
192.168.1.10
88
User Name
Password
Cable Overview
Power cable
RJ45 network cable
RESET (Red)
GND (Black)
Alarm-out (Pink)
Alarm-in (Yellow)
GND (Brown)
* iPad ®
& iPhone® are the registered trademarks of Apple Inc.
Live View & Control ConfigurationAddress Book
Package Content
Camera Screws &
Wall Plugs
Wrenches Quick Setup
443Z
m365a_V0.9
Event Trigger
System
The naming of port forwarding or virtual server
may vary based on di erent router brands. To
know where it is, please refer to the user manual of
your wireless router.
Then, enter the IP address and port number you set
for the camera in Step3, and enable this rule.
Step7: Go to the port forwarding (or virtual server) rule
configuration page.
PORT
PORT
PORT
PORT
PORT
FORWARDING
FORWARDING
FORWARDING
FORWARDING
FORWARDING
ADVANCED
ADVANCED
ADVANCED
ADVANCED
ADVANCED
2. 161
3Continued from the
Previous Page


Produktspezifikationen

Marke: LogiLink
Kategorie: Sicherheitskamera
Modell: AVM365
GPS: Ja
Breite: 117.9 mm
Tiefe: 287.4 mm
Produktfarbe: Grau
Internationale Schutzart (IP-Code): IP67
Übertragungstechnik: Kabelgebunden
Höhe: 212.63 mm
Energiequelle: PoE
Befestigungstyp: Decke/Wand
Betriebstemperatur: -20 - 40 °C
Unterstützte Netzwerkprotokolle: DDNS / PPPoE / DHCP / NTP / SNTP / TCP/IP / ICMP / SMTP / FTP / HTTP / RTP / RTSP / UPnP / RTCP / IPv4 / Bonjour / DNS / UDP / IGMP / QoS
Power over Ethernet (PoE): Ja
Typ: IP-Sicherheitskamera
Betriebsanleitung: Ja
Analoges Signalformatsystem: NTSC, PAL
Unterstützte Video-Modi: 720p
Unterstützte Videoformate: H.264, M-JPEG, MPEG4
Rauschverhältnis (SNR): 48 dB
Größe des Bildsensors: 1/4 "
Blickwinkel (FOV): 62.7 °
PTZ Kontrolle: Ja
Min. benötigter RAM: 256 MB
Formfaktor: Bullet
Maximale Auflösung: - Pixel
Verkabelungstechnologie: 10/100Base-T(X)
IP-Adressen Filter: Nein
DC-Ausgang Volt: +12V
Tag/ Nachtmodus: Ja
Mindestbeleuchtung: 0.1 Lux
LED Typ: IR
Optischer Zoom: - x
Weißabgleich: Auto
Nachtsicht: Ja
Kamera Verschlusszeit: 1/10000 s
Anzahl der Beleuchtungs-LEDs: 45
Alarmeingabe/-ausgabe: Ja
DC Ausgangssstrom: 1.5 A
Feste Brennweite: 3.8 mm
Ethernet/LAN: Ja
Unterstützte Positionierung: Draußen

Brauchst du Hilfe?

Wenn Sie Hilfe mit LogiLink AVM365 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Sicherheitskamera LogiLink

Bedienungsanleitung Sicherheitskamera

Neueste Bedienungsanleitung für -Kategorien-