LiftMaster STAR1000 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr LiftMaster STAR1000 (12 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
1
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is NOT connected BEFORE installing the receiver.
To prevent possible SERIOUS INJURY or DEATH from a moving gate
or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
To prevent possible SERIOUS INJURY or DEATH, the use of
CONSTANT OPERATION on residential openers is PROHIBITED.
When a receiver is used to activate a commercial door opener, a
reversing edge MUST be installed on the bottom of the door. Failure to
install a reversing edge under these circumstances may result in
SERIOUS INJURY or DEATH to persons trapped beneath the door.
COMMERCIAL ACCESS CONTROL RECEIVER
MODEL STAR1000
Control
Station
Receiver Without
Faceplate
Single Operator
9 - 30 volts AC/DC
250 mA max
Power Supply
APPLICATION
The STAR1000 is a high capacity single channel commercial access
control receiver for commercial door operators, and dry contact triggered
devices. The STAR1000 is compatible with Security remote 2.0™
controls and wireless keyless entries, Security Passport and 2.0™
Passport Lite remote controls. This receiver is compatible with
HomeLink®. For programming or compatibility information visit
www.homelink.com. The receiver capacity is 1,000 devices and can be
any combination of remote controls and wireless keyless entries. The
receiver is watertight according to IPX44 specification.
INSTALLATION
1. Select a convenient location near the operator to be controlled by the
receiver within “line of sight” of the intended transmitting location.
NOTE: Do not mount LCD screen in direct sunlight. Avoid mounting
the receiver in a metal enclosure or near other wireless receiving or
transmitting devices.
2. Mount the bracket to the desired surface with appropriate hardware
(not provided) (Figure 1).
3. Remove the 4 (#8) screws on the back of the receiver and remove the
faceplate. Unplug the keypad connector from the control board.
NOTE: Be careful not to damage the keypad cable while removing the
faceplate.
4. Make wiring connections (Figure 2). Refer to your gate or commercial
door operator owner’s manual for more specific information.
5. Reconnect the keypad connector to the board (labeled J9).
6. Secure the faceplate with the 4 (#8) screws previously removed.
7. Install the antenna provided.
NOTE: Use the optional 86LM or 86LMT antenna extension kit
(see page 4) to mount the remote antenna as high and far from
metallic objects as possible for best radio range.
8. Snap the receiver onto the mounting bracket and secure with the
(#8) screws provided.
9. Tighten the watertight connector to secure and seal the wiring.
Figure 1
Mounting Bracket
Watertight Connector
Keypad Connector
Antenna
Connector
Figure 2
Backup Memory
Module
Relay
Connection
Power
Connection
2
Antenna Connection
For the direct antenna or
the antenna extension kit.
“SOFT” Keys
Soft key functions
are defined by the
label on line 5 of the
display. The
functions change
according to the
menu selection.
LCD Screen
System
programming and
status display.
Down/Up Keys
For navigation in
the menus.
Numeric Keypad
Numeric data is
entered through the
numeric keypad.
Insert wiring
USER INTERFACE
The STAR1000 user interface consists of a 22 character by 5 line LCD
display, 3 “soft keys”, Down/Up arrows and a numeric keypad.
PROGRAMMING
The receiver has the ability to learn a combination of remote control
transmitters and keyless entries up to 1,000 devices. See page 4 for a
complete list of compatible accessories. Audible and visual warnings
occur when the receiver capacity is exceeded. After 30 seconds of
inactivity, the receiver times out and the LiftMaster® logo is displayed.
Select “UNLOCK” and enter the PIN to continue.
Initial PIN set up:
The PIN restricts access to authorized administrators only. If you omit
this step, anyone will be able to program the receiver. Upon initial power
up, the system firmware revision is displayed for 5 seconds followed
by the LiftMaster® logo. When a key is pressed, “CREATE PIN?”
is displayed.
1. Press “YES” to create PIN. If the PIN is lost you may request a reset
code by pressing “RESET”.
2. Enter a 6-digit PIN, and press “YES”; enter the 6-digit PIN a second
time and press “YES” to program the PIN. If you make a mistake,
press “CLEAR” to change your entry. To exit the enter PIN screen,
select “BACK”.
3. When your 6-digit PIN is programmed correctly, the LCD display
reads “KEYPAD UNLOCKED”. Select “OK” to continue to the Main
Menu. After 30 seconds of inactivity, the receiver times out and
the LiftMaster® logo is displayed. Select “UNLOCK” and enter PIN
to continue.
Line 1:
Menu and function mode.
Lines 2, 3, and 4:
Menu selections and data.
Line 5:
Soft key function modes.
Scroll Indicator
If more than 3 options exist, a scroll
indicator appears on the left margin of
lines 2, 3, and 4. The scroll indicator
shows the relative position within the list.
Menu/Data selection
shown in inverse font.
3
MAIN MENU COMMAND DESCRIPTION
LEARN MENU LEARN DEVICE Program a device to the receiver.
BLOCK LEARN DEVICE Block program a range of devices to the receiver.
LEARN TO LOC # Program a device to a 4-digit number location.
DELETE MENU DELETE DEVICE Delete a specified device that has been programmed to the receiver.
DELETE ALL DEVICES Delete all programmed devices.
SUSPEND MENU SUSPEND DEVICE Temporarily disables the function of a specified device that has been
programmed to the receiver.
SUSPEND ALL DEVICES Temporarily disables the function of ALL devices programmed to the
receiver.
UNSUSPEND DEVICE Re-enable the function of a suspended device.
UNSUSPEND ALL DEVICES Re-enable the function of ALL suspended devices.
QUERY MENU LOC # USED Displays a range of used locations starting from a specified location.
LOC # AVAILABLE Displays a range of empty locations starting from a specified location.
LOC # SUSPENDED Displays a range of suspended locations starting from a specified
location.
SETTINGS CHANGE PIN Change the 6-digit PIN number for the receiver.
DEALER INFO Display and edit the dealer 11-digit contact phone number.
FIRMWARE VERSION Displays the current firmware version.
BEEP Turn the audible feedback on or off.
MEMORY DUPLICATE MEMORY Creates a memory backup. A backup memory module must be
installed.
RESTORE MEMORY Restores a memory backup from a memory module.
NOTE: Content of memory backup module will over-write any
information already stored in the receiver memory.
RELAY Sets the relay activation time from .25 to 1 second.
CONTRAST Press Down or Up arrows to adjust LCD contrast.
LANGUAGE Sets menu language: English (Default), Spanish, and French.
FACTORY DEFAULT Reset receiver to factory default settings.
PROGRAMMING COMMANDS
The table below describes the commands used to program the receiver.
DIAGNOSTICS
The receiver emits a series of audible beeps to signal programming and
error events. The table at right lists all of the events and their audible
notifications. The On/Off column indicates that the audible notification for
the event may be disabled in the BEEP SETTINGS menu.
EVENT AUDIBLE
NOTIFICATIONS
ON/OFF
Key press Single YES
Successful Add Double
Successful Delete Triple
Successful Suspend Double
Successful Unsuspend Double
Master PIN entry error Long
Programming error Long
Location out of range Long
Generic Success Double
Generic Error Long
Received unknown Tx Slow YES
Received known Tx Double YES
Received known suspended Tx Long YES


Produktspezifikationen

Marke: LiftMaster
Kategorie: Nicht kategorisiert
Modell: STAR1000

Brauchst du Hilfe?

Wenn Sie Hilfe mit LiftMaster STAR1000 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert LiftMaster

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-