LiftMaster LC36M Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für LiftMaster LC36M (22 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 66 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/22
LiftMaster
300 Windsor Drive
Oak Brook, IL 60523-1510
Model LC36M, LC36M41
LiftMaster® Monitored Light Curtain
NOTE: (Images not to scale)
2
Monitored
Light Curtain
Receiver
Monitored
Light Curtain
Transmitter
Primary entrapment protection
ONLY
6" (15 cm) maximum above and a minimum
of 3" (7.62 cm) from the floor
6" (15 cm) maximum above
and a minimum of 3" (7.62 cm)
from the floor
To prevent possible SERIOUS INJURY or DEATH from a closing door:
Be sure to DISCONNECT POWER to the operator BEFORE installing the
Monitored Light Curtain .
The door MUST be in the fully opened or closed position BEFORE
installing the Monitored Light Curtain .
Mount bottom optical sensor of Monitored Light Curtain no higher than
3" to 6" above the ground if used as primary entrapment protection.
Correctly connect and align the Monitored Light Curtain transmitter
and receiver.
The Monitored Light Curtain is for use with LiftMaster
® Commercial
Doors. Use with ANY other product voids the warranty.
DO NOT use this product for the protection of dangerous machinery
or in explosive atmospheres or radioactive environments. Use ONLY
specific and approved types of devices for such applications.
The Monitored Light Curtain MUST be installed ONLY by authorized
and fully trained personnel.
IMPORTANT INFORMATION ABOUT THE MONITORED LIGHT CURTAIN
LiftMaster® Monitored Light Curtain (Model LC36M, Model LC36M41) is an entrapment protection device used with sectional and rolling doors that
is designed with 8 optical sensors that form 22 total invisible light beams. These light beams create a cross-pattern or netting effect for maximum
protection against entrapment. When properly connected and aligned, the Monitored Light Curtain will detect an obstruction in the path of the light
beams. If an obstruction breaks any light beam while the door is closing, the operator will stop and reverse to the full open position. The invisible light
beam must be unobstructed. No part of the door (or door tracks, springs, hinges, rollers or other hardware) may interrupt the light beam while the door
is closing.
When the Monitored Light Curtain is installed as the primary entrapment protection device, the lowest optical sensor will need to be installed 6" (15 cm)
maximum above and a minimum of 3" (7.62 cm) from the floor. If the Monitored Light Curtain is the secondary monitored entrapment protection device
it must be installed 12" (30.5cm) above the primary monitored entrapment protection device. The Monitored Light Curtain Transmitter must be installed
facing the Light Curtain Receiver across the entrapment zone.
NOTE: In this application, in order for the lowest optical sensor to be no higher than 6" above the floor, the wiring of the Monitored Light Curtain must
be facing in the upward direction. If installed with the wires facing down, the lowest optical sensor will be much higher than 6" above the ground; it will
be approx. 9-10" above the ground.
INTRODUCTION
NOTE: (Images not to scale)
3
CARTON INVENTORY
SPECIFICATIONS
Optical
Operating range: 3 - 33 feet (.91 - 10 meters) ............................................
Coverage area: 36" (91.4 cm) detection zone .............................................
Number of optical sensors: 8 ......................................................................
Number of invisible light beams: 22 ............................................................
Receiver LED: Green ...................................................................................
Transmitter LED: Amber .............................................................................
Electrical
Current Draw 40 mA ...................................................................................
Supply voltage: 18 to 30 volts AC or DC .....................................................
Output Type: Open Collector, Pulsed ..........................................................
Mechanical
Housing material: Aluminum, anodized ......................................................
Cable length LC36M: 6'6" (2m) ...................................................................
Cable length LC36M41: 41' (12.5m) ...........................................................
Enclosure rating: IP 67 ...............................................................................
Operating temperature range: - 40°F to +140°F (- 40°C to +60°C) .............
Storage temperature range: - 40°F to +185°F (- 40°C to +85°C) ...............
Dimensions
Light Curtain Receiver
Mounting Brackets (4)
Blocking Material
Light Curtain Transmitter
Red cable end
Green LED
Black cable end
Amber LED
Optical Sensors (8)
2' 9.5"
(86.1 cm)
.2" (5 mm)
.27" (7 mm)
LED
3' 8.25"
(112 cm)
1' 6.23"
(46.3 cm)
.47" (12 mm)
44" (111.8 cm) length with 36" (91.4 cm) detection zone
10" (25.4 cm) Extended Mounting Brackets with Reinforced Ribs for doors with a 2" (5.08 cm) edge
10" (25.4 cm)
2" (5.08 cm)1" (2.54 cm)
APPLICATION
The Monitored Light Curtain is UL Approved and compatible with
LiftMaster LOGIC 5.0 Heavy and Standard-Duty, Medium-Duty,
DDO8900W, LJ8900W, LJ8950W, ATSW, VFOH, HPH1, HPH2, HCTDCUL,
Fire Door Operators (FDC, FDCL, FDO-A, FDO-B), and Egress (LGE)
Commercial Door Operators. The Monitored Light Curtain is for indoor
use only but may be installed in areas exposed to rain or moisture.
INTRODUCTION
The images in this document are for reference only and your product may look different.
ACCESSORIES
Conduit Kit ...............................................................................OES-COND
Conduit kit with 2 junction boxes and 2 flexible cables.
Plug-In Power Supply ...............................................................100MAPS
For Medium Duty Logic, DDO8900W, LJ8900W, LJ8950W, ATSW
LiftMaster commercial door operators that have little or no accessory power
available. Also for use with LOGIC 5.0 operators to provide additional power
for the Light Curtains when multiple Accessories are used. 100MAPS is
always required when 2 sets of light curtains are employed. Up to 2 sets of
Light Curtains may be powered by a single 100MAPS.
Plug-In Optional Card .............................................................CPS3CARD
Required to wire 2nd Monitored Entrapment Protection Device to LOGIC
5.0 Operators.
Not Shown
Screws, Washers, and Nuts with Nylon Insert
Wire Connectors (6)
Installation Manual
Model LC36M - Wire length 6'6"
Model LC36M41 - Wire length 41'


Produktspezifikationen

Marke: LiftMaster
Kategorie: Nicht kategorisiert
Modell: LC36M

Brauchst du Hilfe?

Wenn Sie Hilfe mit LiftMaster LC36M benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert LiftMaster

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-