LiftMaster DDO8900W Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für LiftMaster DDO8900W (64 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 53 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/64
For Light Duty Commercial Use
Install On High-Lift and Vertical Sectional
Doors With
Torsion Assemblies Only
NOT FOR RESIDENTIAL USE
Light-Duty Dock Door Operator for
Sectional Doors
Model DDO8900W
LiftMaster
300 Windsor Drive
Oak Brook, IL 60523
Please read this manual and the enclosed safety materials carefully!
The door WILL NOT CLOSE unless the Protector System® and cable tension monitor are
connected and properly aligned.
Periodic checks of the operator are required to ensure safe operation.
The model number is located on the front cover of the operator.
DO NOT exceed 10 complete cycles of door operation per hour.
This product is to be installed and serviced by a trained door systems technician only. This
product may require adjustments to door springs and/or track configurations. This product is not
intended for use on low headroom tracks with outside pickup drum or doors utilizing extension
springs.
2 YEAR WARRANTY
After Installation, Please Leave with Customer
Register your door operator to receive updates and offers from LiftMaster
Take a photo of the
camera icon including
the points ( ).
Send it in by texting
the photo to 71403
(US) or visit
www.liftmaster.photo
(Global)
2
Introduction
When you see these Safety Symbols and Signal Words on the following pages, they
will alert you to the possibility of if you do not comply with the serious injury or death
warnings that accompany them. The hazard may come from something mechanical or
from electric shock. Read the warnings carefully.
When you see this Signal Word on the following pages, it will alert you to the possibility
of damage to your door and/or the door operator if you do not comply with the cautionary
statements that accompany it. Read them carefully.
Mechanical
Electrical
Safety Symbol and Signal Word Review
This door operator has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict
accordance with the instructions and warnings contained in this manual.
Table of Contents
Introduction 2
Safety Symbol and Signal Word Review 2 ...
Planning 3 ....................................................
Preparing Your Door 4 .................................
Tools Needed 4 ............................................
Carton Inventory 5 .......................................
Hardware 5 ..................................................
Additional Items You May Need 5 ................
Terminal Block Wiring Layout 5 ...................
Assembly 6
Attach the Collar to the Door Operator 6 ......
Attach Mounting Bracket to
Door Operator 7 ...........................................
Installation 7
Position and Mount the Door Operator 8 .....
Attach the Emergency release 9 ...................
Install the Automatic Door
Lock (Not Provided) 9 ..................................
Attach the Cable Tension Monitor
(Required) 10 ...............................................
Install the Three Button
Control Station 11 ........................................
Install the Protector System 12 ....................
Install the Light Curtain (Not Provided) 15 ...
Connect Power 16 ........................................
Install the Battery
Backup (Not Provided) 18 ............................
Install the LMi5 (Not Provided) 19 ...............
Adjustments 20
Program the Travel 20 .................................
Automatic Force Setup 20 ............................
Test the Safety Reversal System 21 .............
Test the Protector System 21 .......................
Test Cable Tension Monitor 22 ....................
Test Automatic Door Lock 22 .......................
To Open the Door Manually 22 ....................
Operation 23
Using Your Door Operator 24 ......................
Programming 25
Remote Control (Not Provided) 25 ...............
To Erase the Memory 25 ..............................
Activating Timer-To-Close (TTC) 26 .............
Maintenance 26
Care of Your Door Operator 26 ....................
Troubleshooting 27
Diagnostic Chart 27 .....................................
Additional Troubleshooting 28 .....................
Repair Parts 30
Installation Parts 30 .....................................
Door Operator Parts 30 ................................
Accessories 31
Contact Information 31
WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer
or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
3
Planning
Survey your area to see if any of the conditions below apply to your installation.
Depending on your requirements, additional materials may be required.
THIS DOOR OPERATOR IS COMPATIBLE WITH:
Doors that use a torsion bar and springs. The torsion bar must be 1" (2.5 cm)
diameter. NOT compatible with reverse wound drums.
4-6" (10-15 cm) drums and tapered drums up to 11" (28 cm) (high and vertical lift).
High lift (up to 54" (137.2 cm) high) and full vertical lift sectional doors up to 14 ft.
(4.3 m) high.
Doors up to 18 ft. (5.5 m) wide.
Doors up to 180 sq. ft. (16.7 sq. m).
Doors up to 300lb (136.1 kg)
NOTE: The optional battery is recommended for doors from 250lbs to 300lbs
to achieve best performance.
Review or inspect proposed installation area. The door operator can be installed on the left
or right side of door. Select the side that
meets the requirements listed below.
a. Must have minimum of 2.5" (6.4 cm)
between the wall and the center of the
torsion bar.
b. Must have minimum of 3" (7.6 cm)
between the ceiling and the center of
torsion bar.
c. Must have minimum of 8.5" (21.6cm)
between the side wall (or obstruction)
and the end of torsion bar.
d. The torsion bar must extend at least
1.5" (3.81 cm) past the bearing.
This may vary depending on your
installation requirements.
e. An electric outlet is required within
6ft. (1.83 m) of the installation area.
If outlet does not exist, contact a
qualified electrician.
f. Depending upon building
construction, operator mounting
brackets, extension brackets or wood
blocks may be needed to install safety
reversing sensors and cable tension
monitor.
g. If the torsion bar is out of round, or
if the normal mounting location is
obstructed, an alternative mounting
kit (480LM) may be used (not
included).
h. Alternate floor mounting of the
safety reversing sensors will require
additional hardware (not provided).
i. Check the seal on the bottom of the
door. Any gap between the floor and
the bottom of the door must not
exceed 1/4 inch (6 mm). Otherwise,
the safety reversal system may not
work properly.
Introduction
NOTE: Inspect the torsion bar while the
door is raised and lowered. It is important
that there is no noticeable movement up
and down or left and right. If the movement
is not corrected, the life of the door
operator will be greatly reduced.
a
b
h
c
d
e
f
g
Torsion
bar
2.5"
(6.4 cm)
3"
(7.6 cm)
Wall or
obstruction
Torsion bar
8.5"
(21.6cm)
Safety
reversing
sensor
Smart LED Light
(Not provided)
Automatic
door lock
(Not
provided)
Door spring


Produktspezifikationen

Marke: LiftMaster
Kategorie: Nicht kategorisiert
Modell: DDO8900W

Brauchst du Hilfe?

Wenn Sie Hilfe mit LiftMaster DDO8900W benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert LiftMaster

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-