Lancom OW-602 Bedienungsanleitung

Lancom Zugangspunkt OW-602

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lancom OW-602 (4 Seiten) in der Kategorie Zugangspunkt. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

LANCOM Antenna Distance Calculator

lancom-systems.com

This guide to the Antenna Distance Calculator supports you in using this tool to

determine the data transfer rates depending on the distance of the antennas of an

outdoor point-to-point (P2P) Wi-Fi connection.

After the calculation you get a tabular overview as well as a diagram of the expected

gross data transfer rates, broken down by the possible channel widths.

Step-by-step instructions

LANCOM Antenna Distance Calculator2

lancom-systems.com

LANCOM Antenna Distance Calculator

Selection of hardware parameters

Start with and select the access point to be used there under Location A Access

point / client adapter Wi-Fi chipset. The installed of the selected access point is

automatically displayed in the next field.

If the access point has an alternative chipset for a different frequency band, you can

select it here.

If available, select the chipset that operates in the 5 GHz band to achieve higher

ranges.

In the next field, the selected should correspond to the most modern Wi-Fi standard

one supported by the chip (802.11ac > 802.11n > 802.11a/g).

Then select the to be used. The cable to be used between access antenna (Cable 1)

point and antenna at location A is determined in the next step.

If you need a surge arrester for the outdoor installation, please select it in the

following field.

The installation of the surge arrester requires an additional cable between it (Cable 2)

and the access point, which you specify in the next field.

If you select a non-standard cable, you have the option to specify the cable

attenuation here. Note that the value must be specified for the total cable length to

be used.

The configuration for location A is now complete. Proceed with the entries for

locationB in the same way.

LANCOM Antenna Distance Calculator3

lancom-systems.com

LANCOM Antenna Distance Calculator

You can configure additional parameters for an interference-resistant P2P connection

in the following steps:



Configure this preferably to ‘yes’ to ensure good connection quality even in bad

weather.



For example, if you are using a longer cable which is not covered by the cable

selection for ‘Cable 1’ or if you have to allow for an additional reserve, enter it here.



Under this item, specify the between the two antennas of the P2P 

connection.

Then, in the line below under , the height in meters is calculated 

in which both antennas must be mounted in order to achieve the calculated gross

transmission rates.

Please note that the maximum height of any obstacles between the antennas must be

added to this value.

 If the value for the calculated mast height would be 5 m and a building with

20 m height would be on a line between the two antennas, a mast of 25 m height

would be necessary.

The  field displays the calculated gross data rate depending

on the configuration you have made. Different values are displayed depending on

different channel widths. The channel widths listed depend, among other things, on

the chipset and the Wi-Fi standard used.

Produktspezifikationen

Marke:	Lancom
Kategorie:	Zugangspunkt
Modell:	OW-602
Bluetooth:	Ja
Bluetooth-Version:	5.1
Produktfarbe:	Weiß
Internationale Schutzart (IP-Code):	IP67
Platzierung:	Pole, Wall
Antennentyp:	Extern
Betriebstemperatur:	-30 - 65 °C
Netzstandard:	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11ax, IEEE 802.11b, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1D, IEEE 802.1v, IEEE 802.1x, IEEE 802.3at
Unterstützte Sicherheitsalgorithmen:	AES-CCMP, AES-GCMP, EAP-FAST, EAP-TLS, EAP-TTLS, MSCHAPv2, PEAP, TKIP, WEP, WPA2-Enterprise, WPA3-Enterprise
Quality of Service (QoS) Support:	Ja
Schnellstartübersicht:	Ja
Power over Ethernet (PoE):	Ja
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	2
Stromverbrauch (max.):	15.2 W
Gehäusematerial:	Kunststoff
Maximale Datenübertragungsrate:	1775 Mbit/s
2,4 GHz:	Ja
Anzahl der Antennen:	4
Montageset:	Ja
Frequenzband:	2400-2483.5, 5150-5700 GHz
Anzahl enthaltener Produkte:	1 Stück(e)
Web-basiertes Management:	Ja
VLAN-Unterstützung:	Ja
Verkabelungstechnologie:	10/100/1000Base-T(X)
5 GHz:	Ja
WLAN-Multimedia (WMM)/(WME):	Ja
Anzahl der SSID-Unterstützung:	32
Fernauthentifizierungs-Einwähl-Benutzerdienst (RADIUS):	Ja
Bluetooth Low Energy (BLE):	Ja
Antenne enthalten:	Ja
Funktionen Service Set Identifier (SSID):	Multiple SSIDs
Antenne Steckertyp:	N-Typ
Maximale Datenübertragungsrate (5 GHz):	1200 Mbit/s
MIMO:	Ja
MIMO-Typ:	Multi User MIMO
Maximale Datenübertragungsrate (2,4 GHz):	575 Mbit/s
Syslog:	Ja
Schnelles Roaming:	Ja
WLAN-Roaming:	Ja
6 GHz:	Nein
Anzahl der VLAN-IDs:	4096