Lancom LN-830U Bedienungsanleitung

Lancom Zugangspunkt LN-830U

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lancom LN-830U (2 Seiten) in der Kategorie Zugangspunkt. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

M O U N T I N G A N D C O N N E C T I N G T H E D E V I C E

Hardware

Power supply 12 V DC, external power adapter (110 or 230 V) with bayonet connector to secure against

disconnection or PoE as per 802.3af via ETH1

Power consumption Approx. 11 W via 12 V / 2 A power adapter (value refers to the power of the access point

without power adapter), about 12 W via PoE, in each case max. +3 W when operating the

USB port.

Environment Temperature range 0 °C to 40 °C for wall mounting (vertical mounting position) and

0 °C to 35 °C for ceiling mounting (horizontal mounting position); humidity 0-95 %;

non-condensing

Housing Robust synthetic housing, rear connectors, ready for wall and ceiling mounting; measures

205 x 42 x 205 mm (W x H x D)

Number of fans None; fanless design, no rotating parts, high MTBF

WLAN

Frequency band 2400-2483.5 MHz (ISM) or 5150-5725 MHz (restrictions vary between countries)

Radio channels 2.4

GHz

Up to 13 channels, max. 3 non-overlapping (2.4-GHz band)

Radio channels 5 GHz Up to 19utomatic dynamic channel selection required)

Interfaces

ETH1 (PoE) 10 / 100 / 1000 Base-TX, autosensing, auto node hub, PoE compliant with IEEE 802.3af

ETH2 10 / 100 / 1000 Base-TX, autosensing, auto node hub

USB USB 2.0 hi-speed host port

Serial interface Serial configuration interface/COM-port (8-pin mini-DIN): 9,600 - 115,000 baud

Declaration of conformity

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in

compliance with Directives 2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006.

The full text of the EU Declaration of Conformity is available at the following Internet address:

www.lancom-systems.com/doc

Package content

Documentation Quick Reference Guide (DE/EN); Installation Guide (DE/EN)

Cable 1 Ethernet cable, 3 m

Power adapter External power adapter, 12 V / 2 A DC/S, barrel connector 2.1 / 5.5 mm bayonet,

LANCOM item no. 111760 (not for WW devices)

T E C H N I C A L D E T A I L S

LANCOM LN-830U

Quick Reference Guide

C ud eadylo -r

a Power

Off Device switched off

Green, permanently* Device operational, resp. device paired /

claimed and LANCOM Management Cloud

(LMC) accessible

Red / green, blinking Configuration password not set. Without a

configuration password, the configuration

data in the device is unprotected.

Orange / green,

blinking alternately with

the WLAN link LED

At least one Wi-Fi module is in managed

mode and has not found a WLAN control-

ler yet. The corresponding Wi-Fi module(s)

is/are switched off until a WLAN controller

is found to supply a configuration, or until

being switched manually into another

operating mode.

Orange / red, blinking

alternately with the

WLAN link LED

At least one Wi-Fi module is in managed

mode and has found a WLAN controller.

However, the WLAN controller cannot

assign a configuration because the

firmware and/or the device's loader

version is not compatible with the WLAN

controller.

1x green inverse

blinking*

Connection to the LMC active, pairing OK,

device not claimed

2x green inverse

blinking*

Pairing error, resp. LMC activation code

not available

3x green inverse

blinking*

LMC not accessible, resp. communication

error

b WLAN Link

Off No Wi-Fi network defined or Wi-Fi module

deactivated. The Wi-Fi module is not

transmitting beacons.

Green, permanently At least one Wi-Fi network is defined and

Wi-Fi module activated. The Wi-Fi module

is transmitting beacons.

Green, inverse flashing Number of flashes = number of connected

Wi-Fi stations and P2P wireless connec-

tions, followed by a pause (default).

Alternatively the frequency of the flashing

can indicate signal strength over the

defined P2P link or the signal strength

between the access point and the device

operating in client mode.

Green, blinking DFS scanning or other scan procedure.

Red, blinking Wi-Fi module hardware error

a b

*) The additional power LED statuses are displayed in 5-seconds

rotation if the device is configured to be managed by the LANCOM

Management Cloud.

Please observe the following when setting up the device

AFor devices to be operated on the desktop, please attach the adhesive rubber footpads

ADo not rest any objects on top of the device and do not stack multiple devices

AIn case of wall or ceiling mounting, use the drilling template as supplied

AKeep the ventilation slots on the side of the device clear of obstruction

ALockable wall and ceiling mounting with the LANCOM Wall Mount (LN)(available as an accessory)

APlease note that when the two Wi-Fi modules are operating in the same frequency band, mutual

interference cannot be ruled out.

aPower

After connecting the cable to the device, turn the connector 90°

clockwise to prevent it from accidental un plugging. Use only the

supplied power adapter.

bConfiguration interface

Use a serial configuration cable to connect the serial interface

(COM) to the serial interface of the device you want to use for

configuring / monitoring (separately available).

cReset button

Pressed up to 5 seconds: device restart

Pressed until first flashing up of all LEDs:

configuration reset and device restart

dEthernet interfaces

Use the Ethernet cable to connect the interfaces ETH1 (PoE) or

ETH2 to your PC or a LAN switch.

eUSB interface (inner right side)

Connect compatible USB devices either directly to the USB

interface, or use a suitable USB cable.

a b c d e

Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!

Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.

LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This docu-

ment contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions. 111815/0421