La Crosse WT551 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für La Crosse WT551 (2 Seiten) in der Kategorie Wecker. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
INTRODUCTION:
The Projection Alarm Clock features radio-controlled time, indoor temperature and
moon phase on a stylish, colorful, and easy to read display. Time and/or indoor
temperature can be projected on a wall or ceiling. Use the integrated USB charging
port to charge your smartphone, camera or other devices when the Projection Alarm
Clock is plugged into a power outlet.
RADIO-CONTROLLED PROJECTION ALARM CLOCK:
SETUP INSTRUCTIONS STEP BY STEP:
STEP 1:
• Insert the 5 volt AC power adapter into the designated area (1) on the back of
the Projection Alarm Clock.
• Insert the power adapter plug into a wall outlet for a continuous backlight.
• The Projection Alarm Clock will light up and display, indoor temperature and
time (12:00).
• IMPORTANT: When operating on A/C power, to avoid interference, the
backlight, projection and USB charge port, will turn off while the Projection Alarm
Clock searches for the DCF signal. The backlight, projection and USB charge
port will function again after the 2-10 minutes search.
STEP 2:
• When backup batteries are desired.
• Remove battery cover from Projection
Alarm Clock, slide tab up and pull out to
remove the cover.
• Insert 2 new AAA batteries (not
included) into the back of the Projection
Alarm Clock (2). Observe the correct
polarity (see marking inside the battery
compartment).
• Do Not Mix Old and New Batteries
• Do Not Mix Alkaline, Standard,
Lithium or Rechargeable Batteries
TROUBLESHOOTING:
• If the Projection Alarm Clock does not display the indoor temperature after 30
seconds remove the A/C power adapter and start the setup process again.
DCF RADIO CONTROLLED TIME
The time base for the radio controlled time is a Cesium Atomic Clock operated by
the Physikalisch Technische Bundesanstalt Braunschweig which has a time
deviation of less than one second in one million years. The time is coded and
transmitted from Mainflingen near Frankfurt via frequency signal DCF-77 (77.5 kHz)
and has a transmitting range of approximately 1,500 km. Your radio-controlled
Projection Clock receives this signal and converts it to show the precise time in
summer or wintertime. The quality of the reception depends greatly on the
geographic location. In normal cases, there should be no reception problems within
a 1,500km radius around Frankfurt.
.
DCF RECEPTION ICON with full signal strength will appear on screen if the
reception of DCF signal is successful. If the unit received DST (summer time)
signal, it will display DST icon.
• The tower icon is solid when the Projection Alarm Clock has received the DCF
signal.
• The tower icon will flash when searching for a signal.
• No tower icon displayed. The Projection Alarm Clock was unable to receive a
signal at this time.
• Reposition the Projection Alarm Clock for better signal reception or try again at
bedtime.
• Hold the -/TIME SEARCH button to force a signal search at night when
reception is best.
• The Projection Alarm Clock will start searching at GMT: 01:00 and if no
reception on the first attempt it will try again at 02:00, 03:00, 04:00 and 05:00.
Each attempt will be at least 2 minutes and the most will be 10 min.
• If there is no signal or too much interference the receiver will only be on for 2
minutes.
• If the signal is good it may catch a signal in ABOUT 2-3 minutes. If the signal is
marginal it will try to catch a signal for up to 10 minutes.
• IMPORTANT: When operating on A/C power, to avoid interference, the
backlight, projection and USB charge port, will turn off while the Projection Alarm
Clock searches for the DCF signal. The backlight, projection and USB charge
port will function again after the 2-10 minute search which occurs during the late
night or early morning hours.
Note: In case the Projection Alarm Clock is not able to detect the DCF signal
(disturbances, transmitting distance, etc.), the time can be manually set using the
program menu.
Note: In normal display mode, press -/TIME SEARCH button to ON/OFF time
searching (DCF).
BUTTON FUNCTIONS:
Button
Press and Rel
ease
Functions Hold 3 seconds
SET/°F/°C
Move through program menu
(setup)
Select temperature in °F/°C
Enter program menu, Set
time, date, etc. (setup)
ALARM
Once
: View Alarm
Twice:
Activate or Deactivate
Alarm Alarm set
+/PROJ
ON/OFF 1 step forward (setup) Fast advance (setup)
Turn Projection ON/OFF
-/TIME SEARCH 1 step backward (setup) Fast backward ( setup)
DCF Search
PROJECTION Rotate Projection 90 degrees
Change what
is projected:
Time/Indoor Temp
alternating (default)
Once:
Time only
Twice: In
door Temp only
Third time: Time/Outdoor
Temp alternating (de
fault)
SNOOZE/LIGHT
HI/LOW/OFF
Once
: Backlight
high
(
A
/
C
)
Twice: Backlight low (A/C
)
3rd time: Backlight OFF
(A/C)
Activate backlight/projection
10 seconds (battery power)
Trigger snooze (alarm
active)
PROGRAM MENU:
The SET/°F/°C button will move through the program menu. The +/PROJ ON/OFF
or -/TIME SEARCH buttons will change a value.
• TIME ZONE: 0H will flash. Press and release the +/PROJ ON/OFF or -/TIME
SEARCH button to set the desired time zone (setting range is 0~+12,0~-12).
Confirm with the SET/°F/°C button and move to the next item.
• LANGUAGE: FR will flash. Press and release the +/PROJ ON/OFF or -/TIME
SEARCH button to select the desire language: GE, IT, NE, ES, DA, EN. Confirm
with the SET/°F/°C button and move to the next item.
• 12/24 HOUR TIME: 12Hr or 24Hr will flash. Press and release the +/PROJ
ON/OFF or -/TIME SEARCH button to select 24Hr or 12Hr. Confirm with the
SET/°F/°C button and move to the next item.
• HOUR: The hour will flash. Press and release the +/PROJ ON/OFF or -/TIME
SEARCH button to select the correct hour. Confirm with the SET/°F/°C button
and move to the next item.
• MINUTES: The minutes will flash. Press and release the +/PROJ ON/OFF or -
/TIME SEARCH button to select the correct minutes. Confirm with the SET/°F/°C
button and move to the next item.
• YEAR: The year will flash. Press and release the +/PROJ ON/OFF or -/TIME
SEARCH button to select the correct year. Confirm with the SET/°F/°C button
and move to the next item.
• MONTH: The month will flash. Press and release the +/PROJ ON/OFF or -/TIME
SEARCH button to select the correct month. Confirm with the SET/°F/°C button
and move to the next item.
• DATE: The date will flash. Press and release the +/PROJ ON/OFF or -/TIME
SEARCH button to select the correct date. Confirm with the SET/°F/°C button
and exit the program menu.
• Note: The Day of the Week will set automatically after the year, month and date
are set.
• If no buttons are pressed in a 20 seconds period, set mode will time out and
return to live display mode, reflecting whatever adjustments were made by user
before timed out.
FAHRENHEIT/CELSIUS: Press and release the SET/°F/°C button to select
temperature readings in Fahrenheit or Celsius.
ALARM SET:
• ALARM HOUR: Hold the ALARM button to enter alarm time setting mode. The
alarm hour will flash. Use the +/PROJ ON/OFF or -/TIME SEARCH button to set
the hour. Press and release the ALARM button.
• ALARM MINUTE: The alarm minutes will flash. Use the +/PROJ ON/OFF or -
/TIME SEARCH button to set the minutes. Press and release the ALARM button
to exit.
ALARM ACTIVATION: ALARM ICON
• Press and release the ALARM button once to show alarm time.
• With the alarm time showing, press and release the ALARM button to activate
the alarm. The alarm icon appears when alarm is active.
• With the alarm time showing, press and release the ALARM button to deactivate
the alarm. The alarm icon will disappear when alarm is inactive.
• Note: Alarm is crescendo sound. When the alarm sounds, it continues for 2
minute and then shuts off completely.
SNOOZE:
• When the alarm sounds, press the SNOOZE button to trigger snooze alarm for 9
minutes. The snooze icon Zz will flash when the snooze feature is active.
• To stop alarm for one day, press ALARM button, while in snooze mode. The
alarm icon will remain solid.
USB Charging
Radio
-
Controlled
Projection
Alarm Clock with Temperature and Moon
Phase
SNOOZE/LIGHT/HI
-
LOW
-
OFF
(TOP)
PROJECTION:
Battery Power: Press and release the SNOOZE/LIGHT button to show the
projection for 10 seconds.
Note: Projection will not display constantly when operating on battery power.
A/C Power: Projection is displayed constantly unless turned off.
• OFF: Hold the +/PROJ ON/OFF button to turn the projection OFF while
operating on A/C power.
• ON: Hold the +/PROJ ON/OFF button to turn the projection ON while operating
on A/C power.
• Rotate Projection: Press and release the PROJECTION button to rotate
projection image 90 degrees. Press and release the PROJECTION button again
to rotate another 90 degrees.
• Change Projection Mode: Hold, then release the PROJECTION button to
switch projection modes. Watch the projection image to view the changes.
o Time and Indoor Temperature: alternate every 5 seconds (default)
o Time: Hold and release PROJECTION button
o Outdoor Temperature: Hold and release PROJECTION button again
BACKLIGHT INTENSITY: Press and release the SNOOZE/LIGHT button to adjust
the brightness of the backlight:
A/C Power: the backlight is displayed constantly unless turned off.
• ON High intensity: The backlight is defaulted to HI when the adapter is in use.
• ON Low intensity: Press and release SNOOZE/LIGHT button once
• OFF: Press and release SNOOZE/LIGHT button
• ON: Press and release SNOOZE/LIGHT button again
• Note: When the adapter is NOT in use, the High/Low/On/Off features are not
available.
Battery Power: Press the SNOOZE/LIGHT button to display the backlight for 10
seconds.
USB CHARGE PORT:
The integrated USB charging port (on back) will charge your smart phone, camera
or other devices when the Projection Alarm Clock is plugged into a power outlet.
Note: This is a power output (charging) port only. This port will not supply power to
the Projection Alarm Clock. • Connect your existing USB charging cord for
your external device to the USB charging
port on the back of the Projection Alarm
Clock to begin to charge. Charging times will
vary.
• Note: Check that your device will charge
with the USB cord it came with. Many
USB cords are for data transfer only, and
cannot be used for charging.
• Output: 0.5A maximum current USB.
• Do NOT overload USB port.
IMPORTANT: When operating on A/C power, the backlight, projection and USB
charging port will turn off while the Projection Alarm Clock searches for the DCF
signal, to avoid interference. The backlight and projection will return after the 2-10
minute search (which occurs during the late night or early morning hours). Then the
USB charging port will resume working.
TEMPERATURE TREND ICONS:
The indoor temperature trend indicators are updated every 30 minutes. These
trends arrows represent temperature changes over the past three hours.
Temperature rising more than 2°F /1°C in the past three hours
Temperature has not changed more than 2°F /1°C in the past three
hours
Temperature falling more than 2°F /1°C in the past three hours
The temperature trend indicators are shown next to the indoor temperature
readings.
MOON PHASE:
The moon phase is based on the year, month and date set (manually or by the DCF
signal).
LOW BATTERY:
• When this icon appears replace the batteries and/or check the A/C adapter of
the Projection Alarm Clock.
CARE AND MAINTENANCE:
• Do Not Mix Old and New Batteries
• Do Not Mix Alkaline, Standard, Lithium or Rechargeable Batteries
• Do not expose the Projection Alarm Clock to extreme temperatures, vibration or
shock.
• Keep Projection Alarm Clock dry.
• Clean the Projection Alarm Clock with a soft damp cloth. Do not use solvents or
scouring agents.
• Improper use or unauthorized opening of housing will void the warranty.
• If the Projection Alarm Clock does not work properly, change the batteries and/or
check the a/c cord connection.
SPECIFICATIONS:
Indoor:
Temperature Range: From 0°C to 50°C (from +32°F to +122°F)
Accuracy: +/- 1°C (2°F)
Resolution : 0.1°
Power:
5-volt a/c power adapter (included)
Optional 2-AAA, IEC, LR3 batteries (not included)
Battery Life: Over 12 months
USB Output: 0.5 Amp maximum current
Dimensions: 133 x 50 x 110 mm (5.23” L x 1.96” W x 4.33” H)
LIABILITY DISCLAIMER
• The electrical and electronic wastes contain hazardous substances. Disposal of
electronic waste in wild country and/or in unauthorized grounds strongly damages
the environment.
• Please contact your local or/and regional authorities to retrieve the addresses of
legal dumping grounds with selective collection.
• All electronic instruments must from now on be recycled. User shall take an
active part in the reuse, recycling and recovery of the electrical and electronic
waste.
• The unrestricted disposal of electronic waste may do harm on public health and
the quality of environment.
• As stated on the gift box and labeled on the product, reading the “User manual” is
highly recommended for the benefit of the user. This product must however not be
thrown in general rubbish collection points.
• The manufacturer and supplier cannot accept any responsibility for any incorrect
readings and any consequences that occur should an inaccurate reading take
place.
• This product is designed for use in the home only as indication of the temperature.
• This product is not to be used for medical purposes or for public information.
• The specifications of this product may change without prior notice.
• This product is not a toy. Keep out of the reach of children.
• No part of this manual may be reproduced without written authorization of the
manufacturer.
R&TTE Directive 1999/5/EC:
Summary of the Declaration of Conformity : We hereby declare that this wireless
transmission device does comply with the essential requirements of R&TTE
Directive 1999/5/EC.
Produktspezifikationen
| Marke: | La Crosse |
| Kategorie: | Wecker |
| Modell: | WT551 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit La Crosse WT551 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Wecker La Crosse
11 August 2024
Bedienungsanleitung Wecker
- Wecker Hama
- Wecker Medion
- Wecker Nedis
- Wecker Philips
- Wecker SilverCrest
- Wecker Oregon
- Wecker Quigg
- Wecker Alecto
- Wecker Auriol
- Wecker Bresser
- Wecker Denver
- Wecker Dexford
- Wecker Irox
- Wecker Jacob Jensen
- Wecker Mebus
- Wecker Sempre
- Wecker Hema
- Wecker Ideen Welt
- Wecker Lenco
- Wecker Edifier
- Wecker FlinQ
- Wecker Geemarc
- Wecker Akai
- Wecker Livoo
- Wecker Casio
- Wecker Balance
- Wecker Fysic
- Wecker Karlsson
- Wecker Krontaler
- Wecker EnVivo
- Wecker Metronic
- Wecker Ascot
- Wecker Lexon
- Wecker Junghans
- Wecker Digi-tech
- Wecker Global Tronics
- Wecker Home Comfort
- Wecker Multi Care Systems
- Wecker Outspot
- Wecker Sonic Alert
- Wecker Bellman
Neueste Bedienungsanleitung für -Kategorien-
5 Oktober 2024
17 September 2024
27 August 2024
27 August 2024
27 August 2024
27 August 2024
26 August 2024
26 August 2024
25 August 2024
25 August 2024