Kyoritsu KEW Mate 2012RA Bedienungsanleitung

Kyoritsu Multimeter KEW Mate 2012RA

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kyoritsu KEW Mate 2012RA (2 Seiten) in der Kategorie Multimeter. Dieser Bedienungsanleitung war für 29 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

DIGITAL MULTIMETER

WITH

AC/DC CLAMP SENSOR

KEW MATE 2012RA

This instrument satisfies the marking requirement defined

in the WEEE Directive. This symbol indicates separate

collection for electrical and electronic equipment.

This marking means they shall be sorted out and collected

as ordained in DIRECTIVE.

This directive is valid only in the EU. When you remove

batteries from this product and dispose them, discard them

in accordance with domestic law concerning disposal. Take

a right action on waste batteries, because the collection

system in the EU on waste batteries are regulated.

# WARNING

●Measurement Category(CAT)

The restrictions on the maximum voltage level for which

the this product can be used, depend on the measurement

categories specified by the safety standards.

Do not apply any input level higher than maximum allowable

input.

AC/DC 600V CAT II AC/DC300V CAT III

CAT II

Appliances, portable equipment, ect. For measurements

performed on circuits directly connected to the low

voltage installation.

CAT III D i st ribu t i o n b oa r d , c i rcu i t bre a k e r, ec t . For

measurements performed in the building installation.

# DANGER

● Never make measurement on circuits with a maximum voltage

difference of 600V or greater between conductors (300V or

greater between a conductor and ground).

● Do not attempt to make measurement in the presence of

flammable gasses.

Otherwise, the use of the instrument may cause sparking,

which leads to an explosion.

● Never attempt to use the instrument if its surface or your hand

is wet.

● Do not exceed the maximum allowable input of measuring

ranges.

● Never open the battery compartment cover while making

measurement.

● Never try to make measurement if any abnormal conditions,

such as broken Clamp Sensor or case is noted.

● The instrument is to be used only in its intended applications or

conditions.

Otherwise, safety functions equipped with the instrument

doesnt work, and instrument damage or serious personal

injury may be caused.

1 SAFETY WARNINGS．

This instrument has been designed and tested according to

IEC Publication 61010: Safety Requirements for Electronic

Measuring Apparatus. This instruction manual contains warnings

and safety rules which must be observed by the user to ensure

safe operation of the instrument and to retain it in safe condition.

Therefore, read through these operating instructions before

starting using the instrument.

# WARNING

● Read through and understand instructions contained in this

manual before starting using the instrument.

● Save and keep the manual handy to enable quick reference

whenever necessary.

● Be sure to use the instrument only in its intended applications

and to follow measurement procedures described in the

manual.

● Be sure to understand and follow all safety instructions

contained in the manual.

Failure to follow the above instructions may cause injury, damage

to the instrument and/or damage to equipment under test.

The symbol # indicated on the instrument means that the user

must refer to related parts of the manual for safe operation of

the instrument. Be sure to carefully read the instructions following

each # symbol in this manual.

# DANGER：

is reserved for conditions and actions that are

likely to cause serious or fatal injury.

# WARNING：

is reserved for conditions and actions that can

cause serious or fatal injury.

# CAUTION：

is reserved for conditions and actions that can

cause minor injury or instrument damage.

Following symbols are used on the instrument and in the

instruction manual. Attention should be paid to each symbol to

ensure your safety.

Refer to the instructions in the manual.

This symbol is marked where the user must refer to the

instruction manual so as not to cause personal injury or

instrument damage.

Indicates an instrument with double or reinforced insulation.

Indicates that this instrument can clamp on bare conductors

when measuring a voltage corresponding to the applicable

Measurement category, which is marked next to this symbol.

Indicates AC (Alternating Current)．

Indicates DC (Direct Current).

# WARNING

● Never attempt to make any measurement, if any abnormal

conditions are noted, such as broken case, cracked test leads

or Clamp Sensor Cable and exposed metal parts or internal

wiring.

● Do not turn the Function Selector Switch while the test leads

are connected to the circuit under test.

● Do not install substitute parts or make any modification to

the instrument. Return the instrument to Kyoritsu or your

distributor for repair or re-calibration.

● Do not try to replace the batteries if the surface of the

instrument is wet.

● Always disconnect the clamp sensor and the test leads

from the circuit under test and switch off the instrument

before opening the battery compartment cover for battery

replacement.

● A cap is provided on the tip of a test lead. Use a test lead with

the cap on for safety.

● Stop using the test lead if the outer jacket is damaged and the

inner metal or color jacket is exposed.

# CAUTION

● Make sure that the Function Selector Switch is set to an

appropriate position before making measurement.

● Always make sure to place the test leads in the holster before

making current measurement.

● Do not expose the instrument to the direct sun, extreme

temperatures or dew fall.

● This instrument isn't dust & water proofed. Keep away from

dust and water.

● Be sure to set the Function Selector Switch to the "OFF"

position after use. When the instrument will not be used for

a long period of time, place it in storage after removing the

batteries.

● Use a damp cloth and detergent for cleaning the instrument.

Do not use abrasives or solvents.

● Keep your fingers and hands behind the protective fingerguard

during measurement.

3 SPECIFICATIONS．

● Measuring Ranges and Accuracy (at 23 , relative ℃ ℃±5

humidity75% or less)

AC Current  A (RMS value detection)

Maximum Input Current : 120A

Range Display range Allowable input Accuracy

60A 0.00

～60.39A 0.00～60.00Arms

(85Apeak or less) ±2.0%rdg±5dgt

(45～65Hz)

（）sine wave

120A 0.0～603.9A 0.0～120.0Arms

(170Apeak or less)

※ For non-sinusoidal waveforms, add ±(2% of reading + 2% of

full scale), for Crest factor<2.5.

DC Current  A Maximum Input Current : 120A

Range Display range Allowable input Accuracy

60A ±0.00～60.39A ±0.00

～60.00A ±2.0%rdg±8dgt

120A ±0.0～603.9A ±0.0～120.0A ±2.0%rdg±5dgt

AC Voltage  V (RMS value detection, Auto-range) Maximum Input Voltage : 600V

Range Display range Allowable input Accuracy

6V 0.000 ～6.039V

0.300～600.0Vrms

(850Vpeak or less)

±1.5%rdg±5dgt

(45～400Hz)

（）sine wave

60V 5.60～60.39V

600V 56.0～603.9V

※Input Impedance：approx. 10M <200pFΩ

※ For non-sinusoidal waveforms, add ±(2% of reading + 2% of

full scale), for Crest factor<2.5.

DC Voltage  V (Auto-range) Maximum Input Voltage : 600V

Range Display range Allowable input Accuracy

600mV ±0.0～603.9mV

±0.0m～600.0V ±1.0%rdg±3dgt

6V ±0.560～6.039V

60V ±5.60～60.39V

600V ±56.0

～603.9V

※Input Impedance：approx. 10MΩ

Resistance (Auto-range)Ω

Range Display range Allowable input Accuracy

600 0.0Ω～603.9Ω

0.0Ω～60.00MΩ

±1.0%rdg±5dgt

6k 0.560Ω～6.039kΩ

60k 5.60Ω～60.39kΩ

600k 56.0Ω～603.9kΩ

6MΩ

0.560～6.039MΩ

±2.0%rdg±5dgt

60M 5.60Ω～60.39M ±3.0%rdg±5dgtΩ

※ Open-loop Voltage：approx.0.6V, Measuring Current : 0.3mA or

less

Continuity

Range Display range Allowable input Accuracy

600 0.0Ω～603.9 0.0Ω～600.0 ±1.0%rdg±5dgtΩ

※ ΩThe buzzer turns on for resistances lower than 35±25 .

※ Open-loop Voltage：approx.0.6V, Measuring Current : 0.3mA

or less

Diode 

Range Display range Allowable input Accuracy

2V 0.000

～1.999V 0.000～1.999V ±3.0%rdg±5dgt

※Open-loop Voltage：approx.2.7V

Capacitor (Auto-range)

Range Display range Allowable input Accuracy

40nF 0.00

～40.39nF the accuracy is not guaranteed

400nF 36.0～403.9nF

40.0n

～40.00 Fμ

±2.5%rdg±10dgt4 F 0.360μ～4.039 Fμ

40 F 3.60μ～40.39 Fμ

400 F 36.0μ～403.9 Fμ

the accuracy is not guaranteed

4000 F 360μ～4039 Fμ

Frequency Hz ( AC Current ) (Auto-range)

Range Display range Allowable input Accuracy

10Hz 0.000～9.999Hz The accuracy is not guaranteed

100Hz 9.00

～99.99Hz 9.00Hz～400.0Hz ±0.2 rdg±2dgt％

1000Hz 90.0～400.0Hz ±0.1 rdg±1dgt％

400.1～999.9Hz

The accuracy is not guaranteed

10kHz 0.900

～9.999kHz

100kHz 9.00～99.99kHz

1000kHz 90.0～999.9kHz

10MHz 0.900～9.999MHz

※Input Current：more than 6A

Frequency Hz ( AC Voltage ) (Auto-range)

Range Display range Allowable input Accuracy

10Hz 0.000～9.999Hz The accuracy is not guaranteed

100Hz 9.00

～99.99Hz

9.00Hz～300.0kHz

±0.2 rdg±2dgt％

1000Hz 90.0

～999.9Hz

±0.1 rdg±1dgt％

10kHz 0.900

～9.999kHz

100kHz 9.00～99.99kHz

300kHz 90.0～300.0kHz

1000kHz 300.1～999.9kHz The accuracy is not guaranteed

10MHz 0.900～9.999MHz

※ Input Voltage：more than 6V (～10kHz) , more than 20V (10k

～300kHz)

※Input Impedance：approx. 900kΩ

Note:◇ The symbol of " ―" in the above table means that the

instrument only displays the value, but the accuracy, the

proper operation and the safety are not guaranteed.

2 FEATURES．

● Permits AC/DC current measurement up to 120A using a

clamp sensor that comes standard with the instrument

● Clamp sensor for ease of use in crowded cable areas and

other tight places

●

Permits current measurement with an open current-clamp sensor

that does not require opening and closing operations by the user

●True-RMS measurements ACV and ACA.

●Auto-power-save function

●Buzzer for easy continuity checking

●Data hold function to freeze the readings

●LCD with a bar graph

●Shock absorbing holster for ease of storage

●

Designed to international safety standard IEC61010-1: over-voltage

category CAT III 300V, CAT II 600V and pollution degree 2.

[ Effective Value (RMS) ]

Most alternating currents and voltages are expressed in

effective values, which are also referred to as RMS (Root-Mean-

Square) values.

The effective value is the square root of the average of square

of alternating current or voltage values. Many clamp meters

using a conventional rectifying circuit have "RMS" scales for AC

measurement. The scales are, however, actually calibrated in

terms of the effective value of a sine wave though the clamp

meter is responding to the average value. The calibration is

done with a conversion factor of 1.111 for sine wave, which

is found by dividing the effective value by the average value.

These instruments are therefore in error if the input voltage or

current has some other shape than sine wave.

[ CF (Crest Factor) ]

CF (Crest Factor) is found by dividing the peak value by the

effective value.

Examples: Sine wave: CF=1.414

Square wave with a 1: 9 duty ratio: CF=3

●Safety Standard

IEC 61010-1, 61010-2-032, 61010-2-033

CAT III 300V, pollution degree 2

CAT II 600V, pollution degree 2

IEC 61010-031

EN 61326-1 (EMC)

EN 50581 (RoHS)

● ΔΣOperating System modulation

●Display Liquid crystal display

Maximum Reading:6039

Except Hz : 9999, CAP : 4039,

Diode : 1999

Bar graph with maximum points of 30.

●Display approx. 3 times per second

Indication renewal

●Location for use

Indoor use, 2000m max, above sealevel

●

Operating Temperature

0 ~ +40 , relative humidity 85% or less℃

and Humidity Range (without condensation)

●Storage Temperature

-20 ~ +60 , relative humidity 85% or less℃

and Humidity Range (without condensation)

●Source Two 1.5VDC R03 (UM-4) batteries

●Current Consumption approx. 3mA (DCV), approx. 13mA

(ACA)

●Power-save Function Shifts to the power-save state about

15 min ut es af ter t he last switch

operation.

●Low battery warning  Appears when the batteries

become low (2.4±0.15V or less)

●Overload Protection AC voltage / DC voltage / Frequency

ranges :

DC / ACrms 720V for 10 seconds

AC current / DC current ranges :

DC / ACrms 150A for 10 seconds

Resistance / Continuity / Diode /

Capacitor ranges :

DC / ACrms 600V for 10 seconds

●Withstand Voltage AC3470Vrms for 5 seconds between

electrical circuit and housing case

● ΩInsulation Resistance 100M or greater at 1000V

between electrical circuit and housing

case

● φConductor Size Approx. 12mm diameter max

●Dimensions 128(L)×92(W)×27(D)mm

●Weight Approx. 220g

●Accessories Two R03 (UM-4) batteries

Instruction Manual

INSTRUCTION MANUAL

Waveform

Crest factor

Average value

Vavg

Effective value

Vrms

Conversion

factor

Vrms/ Vavg

Reading errors for

average sensing

instrument

≒ ≒0.637 1.111 ≒1.414

≒1.155 ≒1.732

＝％-3.8

× ％100

＝％11.1

≒0.707

0.5A 1.111-×3

A A

0.5A

0％

＝

A A＝・D

A 1,111-A××100

×100

＝

（　　1.111 -1）

D=f/T

DISTRIBUTOR

Kyoritsu reserves the rights to change specifications

or designs described in this manual without notice

and without obligations.

6-18 92-2316A

4 INSTRUMENT LAYOUT．

Clamp Sensor：Pick up current flowing through the conductor.

Barrier (Protective figerguard)：It is a part providing protection

against electrical shock and ensuring the minimum required air

and creepage distances.

A Zero Adjust Button：Used for zero adjustment on DCA. Also used

to reset the display resding.

Data Hold Button：Freezes the display reading.

Function Selector Switch：Selects function. Also used to power the

instrument on.

Range Selector Button：Selects measuring mode. When the

Ω range the defaults to the Resistance. Then, press this

switch to cycle through Resistance Diode Cotinuity → → →

Capacitor → Resistance. When the 60A, 120A range the

defaults to the AC. Then, press this switch to cycle through AC

→ → DC AC.

Test Lead Cap：Test leads can be used under the CAT.II and III

environments by attaching a Protective cap as illustrated

below. Use of our Protective cap offers different lengths

suitable for the test environments.

# CAUTION

● The Cap should be firmly attached to the Probes.

5 PREPARATIONS FOR MEASUREMENT．

（）1 Checking battery voltage

Set the Function Selector Switch to any position other than

the OFF position. If the marks on the display is clearly legible

without symbol " " showing, battery voltage is OK.

If the display blanks or " " is indicated, replace the

batteries according to section 8: Battery Replacement.

NOTE

● When the instrument is left powered on, the auto-power-save

function automatically shut the power off; The display blanks

even if the Function Selector Switch is set to a position other

than the OFF position in this state.

To power on the instrument, turn the Function Selector Switch

or press any Button. If the display still blanks, the batteries are

exhausted.

Replace the batteries.

（）2 Make sure that the Function Selector Switch is set to the

appropriate range.

Also make sure that data hold function is not enabled. If

inappropriate range is selected, desired measurement

cannot be made.

（）3 Permits the measurement by placing the

one test lead in the holster while confirming

the measurement value.

# WARNING

● Verify proper operation on a known source before use or taking

action as a result of the indication of the instrument.

6-4 Diode Measurement

(1) Set the Function Selector Switch to " ".

(2) Press the SEL Button. "" mark is shown on the display.

(3) Connect the test leads to the circuit under test.

The measured value appears on the display.

[ Forward-bias Diode Test ]

Connect the red test lead to the anode and the black test

lead to the cathode.

[ Reverse-bias Diode Test ]

Connect the red test lead to the cathode and the black test

lead to the anode.

Note:◇ Hold the clamp sensor in the holster, while making the

diode measurement

6-5 Continuity Measurement

(1) Set the Function Selector Switch to " ".

(2) Press the SEL Button. " " mark is shown on the display.

(3) Connect the test leads to the circuit under test.

The measured value appears on the display.

When the measurement value is lower than 35±25Ω, the

instrument beeps.

Note:◇ Hold the clamp sensor in the holster, while making the

continuity measurement

6-6 Capacitor Measurement

(1) Set the Function Selector Switch to " ".

(2) Press the SEL Button. "F" mark is shown on the display.

(3) Connect the test leads to the circuit under test.

The measured value appears on the display.

Note:◇ Hold the clamp sensor in the holster, while making the

capacitor measurement.

6-7 Frequency Measurement

# DANGER

● In order to avoid possible shock hazard, never make

measurement on circuits with a maximum voltage difference

of 600V or greater between conductors (300V or greater

between a conductor and ground).

● Do not make measurement with the test leads connected

to the circuit under test. Never make measurement with the

battery compartment cover removed.

● Do not make current measurement with the test leads

connected to the circuit under test.

● Keep your fingers and hands behind the protective fingerguard

during measurement.

(1) Set the Function Selector Switch to "Hz."

(2) Measuring frequency of current:

Adjust one of the conductors to the center of the clamp

sensor's arrow.

Measured value is shown on the display.

Measuring frequency of voltage:

Connect the test leads to the circuit under test. Measured

frequency is shown on the display.

Note:◇ Do not use both the clamp sensor and the test leads at

the same time, while making the frequency measurement.

◇ Hold the test leads in the holster, while making the frequency

measurement by using the clamp sensor.

◇ Hold the clamp sensor in the holster, while making the

frequency measurement by using the test leads.

7 OTHER FUNCTIONS．

7-1 Auto-Power-Save Function

NOTE

● A small amount of current is consumed even in the power-save

state. Make sure to set the Function Selector Switch to the

OFF position when the instrument is not used.

This function helps to avoid unwanted exhaustion of the batteries

because of leaving the instrument powered on and extend battery

life.

The instrument automatically shifts to the power-save state about

15 minutes after the last Function Selector Switch or other switch

operation.

A minute before power-save mode the instrument beeps 5 times,

finally beeps longer and then shifts to the power-save mode.

To return to the normal state:

Press the Button or the SEL Button to return from the

power-save mode state to the normal state.

Note:◇ Pressing the Button or the SEL Button over 2 sec

to return from the power-save mode state, the function of

each button is also enabled.

(ex.) When the function is 60A and in the power-save

mode, pressing SEL Button over 2sec releases the

power-save mode and changes from initial  AC mode to

 DC mode.

To cancel the Auto-Power-Save Function

To cancel the Auto-Power-Save Function, turn the function

switch from OFF position to any other position with pressing

SEL Button.

Note:◇ When the function switch is 60A or 120A, pressing A

ZERO ADJ Button over 2 sec enables to cancel the Auto-

Power-Save Function.

In this case, pressing A ZERO ADJ Button over 2 sec once

agin enables the Auto-Power-Save Function.

To enable the Auto-Power-Save Function once again

Turn the function switch to the OFF, and then to any position.

7-2 Data Hold Function

This is a function to freeze a measured value on the display.

Press the Button once to hold the current reading. In this

data hold state, the reading is held even if input varies. " "

mark is shown on the LCD. To exit the data hold state, press the

Button again.

Note:◇ Data Hold Function is not effective while making

Continuity or Diode measurement.

◇ When the function is on the position where SEL Button or

A ZERO ADJ Button is effective, pressing SEL Button or

A ZERO ADJ Button cancels the held indication.

8 BATTERY REPLACEMENT．

# WARNING

● In order to avoid possible shock hazard, always disconnect

the test leads from the circuit under test and set the Function

Selector Switch to the OFF position before trying to replace the

batteries.

# CAUTION

●Do not mix new and old batteries.

● Install batteries in the orientation as shown inside the battery

compartment, observing correct polarity.

When the battery voltage warning mark " " is shown on the

top left corner of the LCD, replace the batteries. Note that the

display blanks and " " mark is not shown if the batteries are

completely exhausted.

(1) Set the Function Selector Switch to "OFF."

(2) Remove the instrument from the holster.

(3) Loosen the battery-compartment-cover-fixing screw on the

lower back of the instrument.

(4) Replace the batteries with two new R03 (UM-4) 1.5V batteries.

(5) Put the battery compartment cover back in place and tighten

the screw.

[ How to storage the clamp sensor and the test leads ]

6 HOW TO MAKE MEASUREMENT．

6-1 Current Measurement

# DANGER

● In order to avoid possible shock hazard, never make

measurement on circuits with a maximum voltage difference

of 600V or greater between conductors (300V or greater

between a conductor and ground).

● Do not make measurement with the test leads connected to

the circuit under test.

● Never make measurement with the battery compartment cover

removed.

● Keep your fingers and hands behind the barrier during

measurement.

● To avoid electrical shock by touching the equipment under test

or its surroundings, be sure to wear insulated protective gear.

# CAUTION

● When handling the clamp sensor, exercise caution not to apply

excessive shocks or vibration to the sensor.

●Maximum measurable conductor size is 12mm in diameter.

Note: ◇ Make sure that the test leads are in the holster while

making current measurement.

◇

Instrument can show the value over 120A, but the safe and

proper measurement range is limited lower than 120A.

6-1-1 DC Current Measurement

(1) The Function Selector Switch to the "60A" or "120A" position.

("AC" marks are shown on the top of the display.)

(2) Press the SEL Button. " " mark is shown on the display.

(3) Press the A ZERO ADJ Button to set the reading of the

instrument to zero.

(Incorrect zero adjustment makes measurement errors.)

(4) Adjust one of the conductors to the center of the clamp

sensor's arrow.

( When the position of the conductor is not at the center of

the arrow, the error occurs.)

Measured value is shown on the display.

Note:◇ The direction of current is plus(+) when the current

flows from the upside (A ZERO ADJ. Button side) to the

underside The direction is minus(-) when the current flows

from the underside to the upside.

◇ Minus "-" mark is shown at the left side of the value and

the bar graph while making minus current measurement.

◇ By changing the function switch 60A or 120A to the other

position, the AC/DC mode is reset to the default (AC

mode). To set the DC mode, press the SEL Button again.

◇ The zero adjustment is effective only for the current

measurement.

◇ After the zero adjustment the instrument operates as

follows.

(1) The bar graph disappears.

(2) The maximum counts is changed according to the

adjusted value.

(ex.)

The maximum count is 6039-100=5939, when

adjusted +100 counts to zero.

(3)  △mark is shown on the display.

(4)

Pressing A ZERO ADJ. Button again or

SEL

Button,

changing the function switch releases zero adjustment

function when the zero adjustment is effective.

◇ Pressing the A ZERO ADJ button over 2 sec releases the

zero adjustment function.

6-1-2 AC Current Measurement

(1) Set the Function Selector Switch to "60A." or "120A".

(" " mark is shown on the top of the LCD.)

(2) Adjust one of the conductors to the center of the clamp

sensor's arrow.

( When the position of the conductor is not at the center of

the arrow, the error occurs.)

Measured value is shown on the display.

Note:◇ Unlike DC current measurement, zero adjustment is not

necessary. There is not polarity indication either.

6-2 Voltage Measurement

# DANGER

● In order to avoid possible shock hazard, never make

measurement on circuits with a maximum voltage difference

of 600V or greater between conductors (300V or greater

between a conductor and ground).

● Do not make measurement with the battery compartment

cover removed.

● Keep your fingers and hands behind the barrier during

measurement.

Note:◇ Make sure that the clamp sensor is in the holster while

making voltage measurement.

◇ I

nstrument may show the value over 600V, but the safe

and proper measurement range is limited lower than 600V.

6-2-1 DC Voltage Measurement

(1) Set the Function Selector Switch to " ".

(" " mark is shown on the LCD.)

(2) Short-circuit the tips of test leads to make the indication zero.

(3) Connect the red test lead to the positive (+) side of the circuit

under test and the black test lead to the negative (-) side.

Measured voltage value is shown on the display.

When the connection is reversed, "-" is shown on the display.

6-2-2 AC Voltage Measurement

(1) Set the Function Selector Switch to " ".

(" " mark is shown on the LCD.）

(2) Connect the test leads to the circuit under test.

Measured voltage value is shown on the display.

Note:◇ The displayed value might be few digits instead of zero

even if shorting the test leads.

6-3 Resistance Measurement

# DANGER

●Never make measurement on circuits that are live.

● Never make measurement with the battery compartment cover

removed.

● Keep your fingers and hands behind the protective fingerguard

during measurement.

(1) Set the Function Selector Switch to " ".

(2) Press the SEL Button and " " mark is shown and " " mark Ω

is not shown on the display (Resistance Measurement).

Immediately after setting the Function Selector Switch to

" ", is not necessary to operate the SEL Button.

(3) Check that the display shows " ". Short the test leads and

check that the display reads about zero.

(4) Connect the test leads to the circuit under test. Measured

resistance value is shown on the display.

Note: ◇

When the test leads are shorted, the display may read a small

resistance value. This is the resistance of the test leads.

◇ If there is an open in either of the test leads, " " is

shown on the display.

◇ The capacitive factor of the tested circuit may cause the

fluctuation of the measurement value, while making the

resistance measurement of high value .

◇ Make sure that the clamp sensor is in the holster while

making resistance measurement.

Adjust Button

Clamp Sensor

Barrier

A Zero

Clamp Sensor

Cable

Function Selector Switch

Data Hold

Button

Range Selector

Button

（　 Button ）（　

Button ）

Holster

LCD Display

Test Lead

Protective fingerguard

Test Lead Cap

Continuity

Capacitor

Diode

Resistance

････Resistance

60A, 120A････AC

default setting

Battery Voltage

AC / DC

Continuity

Data Hold

Bar Graph

Unit

Zero ADJ

Diode Test

Buzzer

Warning

Adjust a

conductor to

the center of

the arrow.

Correct

Incorrect

Conductor

Black Red

Forward-bias Diode Test

Test Lead

AnodeCathode

Red Black

Reverse-bias Diode Test

Test Lead

AnodeCathode

Prohibition

Battery

Compartment

Cover

Batteries

Screw

Wind the lead around the folder.

Test Leads

Clamp Sensor

Protective Cap Exposed metal part

Uncapped condition for CAT.II environment

Capped condition for CAT.III environments

Produktspezifikationen

Marke:	Kyoritsu
Kategorie:	Multimeter
Modell:	KEW Mate 2012RA

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kyoritsu KEW Mate 2012RA benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Multimeter Kyoritsu

Kyoritsu 1009 Bedienungsanleitung

27 September 2024

Kyoritsu KEW2046R Bedienungsanleitung

20 September 2024

Kyoritsu KEW 2510 Bedienungsanleitung

29 August 2024

Kyoritsu KEW 2413R Bedienungsanleitung

29 August 2024

Kyoritsu 2431 Bedienungsanleitung

29 August 2024

Kyoritsu 2434 Bedienungsanleitung

29 August 2024

Kyoritsu KEW Snap 2433 Bedienungsanleitung

29 August 2024

Kyoritsu KEW 2300R Bedienungsanleitung

28 August 2024

Kyoritsu KEW 1052 Bedienungsanleitung

9 August 2024

Kyoritsu KEW2200 Bedienungsanleitung

5 August 2024

Bedienungsanleitung Multimeter

Neueste Bedienungsanleitung für -Kategorien-

PCE Instruments PCE-228 Bedienungsanleitung

16 Oktober 2024

PCE Instruments PCE-PHM 14 Bedienungsanleitung

16 Oktober 2024

PCE Instruments PCE-LT 15 Bedienungsanleitung

16 Oktober 2024

PCE Instruments PCE-ITM 20 Bedienungsanleitung

16 Oktober 2024

PCE Instruments PCE-IT 200 Bedienungsanleitung

16 Oktober 2024

Metrix MX 24 Bedienungsanleitung

13 Oktober 2024

FLIR DM166 Bedienungsanleitung

9 Oktober 2024

Velleman DVM840 Bedienungsanleitung

5 Oktober 2024

Velleman DVM852 Bedienungsanleitung

5 Oktober 2024

Fluke 325 Bedienungsanleitung

3 Oktober 2024