Kreg Rip-Cut Bedienungsanleitung

Kreg Sägemaschine Rip-Cut

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kreg Rip-Cut (24 Seiten) in der Kategorie Sägemaschine. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/24

Rip-Cut

™

ITEM No. KMA2685-INT

NK9036

Version 2 - 02/2019

www.kregtool.com • 800.447.8638

Owner’s Manual | Benutzerhandbuch | Guide d’utilisation | Manual del propietario

WARNING When using electric tools, always follow the safety precautions below to reduce the risk of re, electric shock

and personal injury. Read all of these instructions before attempting to operate this product. SAVE THESE INSTRUCTIONS.

General Safety Guidelines

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Don’t use power tools in a dangerous environment. Don’t use

power tools in damp or wet locations, or expose them to rain.

c) Do not operate power tools in explosive atmospheres,

such as in the presence of ﬂammable liquids, gases or dust.

Power tools create sparks that can ignite the fumes or dust.

d) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

e) Make your workshop childproof. Use padlocks or master

switches, or remove starter keys.

2) Electrical safety

a) Earth electric tools. If the tool is equipped with a three-

prong plug, it must only be plugged into an earthed three-

hole electrical socket. If the proper socket is not available,

have one installed by a qualiﬁed electrician. Never remove

the third prong or modify the provided plug in any way.

b) Do not expose power tools to rain or wet conditions. Water

entering a power tool increases the risk of electric shock.

c) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges and moving parts. Damaged or

entangled cords increase the risk of electric shock.

d) Use a proper extension cord and make sure it is in good

condition. When using an extension cord, make sure that you

use one that is heavy enough to carry the current your power

tool draws. An undersized cord causes a drop in line voltage

resulting in loss of power and overheating. Table 1 shows the

correct cord gauge to use depending on cord length and tool

nameplate ampere rating. If in doubt, use the next heavier

gauge. The smaller the gauge number, the heavier the cord.

e) When operating electric tools, avoid body contact with

earthed surfaces such as pipes, radiators, kitchen hobs and

refrigerators. Contact with an earthed surface increases the

risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power tool

while you are tired or under the inﬂuence of drugs, alcohol or

medication. A moment of inattention while operating power

tools can result in serious personal injury.

b) Always wear safety glasses. Everyday glasses are not

safety glasses. Safety glasses have specially constructed

lenses, frames and side shields.

c) Use safety equipment. Use a face or dust mask when the

cutting operation is dusty. Safety equipment such as a dust

mask, non-skid safety shoes, hard hat or hearing protection

used for appropriate conditions reduces personal injuries.

d) Avoid accidental starting. Make sure the switch is in the

off-position before plugging in. Carrying power tools with

your ﬁnger on the switch or plugging in power tools that have

the switch on invites accidents.

e) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool can result in personal injury.

f) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

g) Secure workpieces. Use clamps or a vice to hold work

when practical. This is safer than using your hand and it frees

both hands to operate the tool.

h) Never stand on the machine. Serious injury can occur if the

tool tips or if the cutting tool is unintentionally contacted.

i) Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving parts.

Loose clothes, jewellery or long hair can be caught in moving

parts. Roll up long sleeves to the elbow. Wear protective hair

covering to contain long hair.

j) If devices are provided for the connection of dust extraction

and collection equipment, ensure these are connected and

properly used. Use of these devices reduces dust-related

hazards.

4) Power tool use and care

a) Keep guards in place and in working order.

b) Do not force the power tool. Use the correct power tool for

your application. The correct power tool will do the job better

and more safely at the rate for which it was designed.

c) Use the right tool. Don’t force a tool or attachment to do

a job for which it was not designed.

d) Do not use the power tool if the switch does not turn it on

and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

e) Disconnect the plug from the power source and/or

the battery pack from the power tool before making any

adjustments, changing accessories or storing power tools.

Such preventive safety measures reduce the risk of starting

the power tool accidentally.

f) Never leave a tool running unattended. Turn power off.

Do not leave the tool until it has come to a complete stop.

g) Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool and

these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

h) Maintain power tools. Check for misalignment or binding

of moving parts, broken parts and any other condition that

can affect power tool operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained power tools.

i) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

j) Use the recommended speed for the cutting tool or

accessory and workpiece material.

k) Only use parts and accessories recommended by the

manufacturer. Consult the owner’s manual for recommended

accessories. Using improper accessories can cause personal

injury.

l) Use the power tool, accessories and tool bits in accordance with

these instructions and in the manner intended for the particular

type of power tool, taking into account the working conditions and

the work to be performed. Use of the power tool for operations

different from those intended can result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualiﬁed repair person

using only identical replacement parts. This ensures that the

safety of the power tool is maintained.

6) SAFETY INSTRUCTIONS SPECIFIC TO USING THE RIP-CUT™

a) Before using the Rip-Cut™, read, understand and follow

the safety warnings and operation instructions included with

this product and provided by your saw manufacturer. Keep all

guards and safety devices in place.

b) Wear correct eye, ear and respiratory protection when

operating your saw.

c) Use a sharp blade designed for the type of material you are

cutting.

d) Always disconnect your saw from power before making

adjustments to the saw or Rip-Cut

™.

General Safety Guidelines

TABLE 1

Nameplate

Amperes

@120 V

Extension Cord Length

25' 50' 75' 100' 150' 200'

Recommended Wire Gauge

0 -5 16 16 16 14 12 12

5.1 - 8 16 16 14 12 10 NR

8.1 -12 14 14 12 10 NR NR

12.1 - 16 12 12 NR NR NR NR

NR – Not Recommended

WARNING:

This product can expose you to chemicals including Acrylonitrile

and other chemicals, which are known to the State of California to cause cancer and

reproductive harm. For more information, go to www.P65Warnings.ca.gov.

e) Check the cursor alignment before you cut.

f) Ensure that the saw blade will not contact the edge guide

during the cut.

g) Do not attempt a cut when any part of the Rip-Cut

™ sled

interferes with the operation of the saw blade guard.

h) Fully support both the workpiece and the cut-off piece to

prevent binding and kickback.

i) Adjust the depth of cut so that the saw blade protrudes

1⁄ [3 mm] through the workpiece during the cut.8”

j) Keep your hands away from the saw blade during

operation. Do not reach under the workpiece while cutting.

k) Secure your workpiece to ensure that it doesn’t move

during the cut.

l) Do not use excessive force when cutting.

Maintain a steady and controlled pace.

m) Allow the saw blade to come to a complete stop before

lifting the Rip-Cut from your workpiece.

n) Maintain your tools and accessories.

Check for misalignment or binding of moving parts, loose

fasteners, broken parts and any other condition that may

affect safe operation. If an unsafe condition is discovered,

correct it before use.

7) Kickback

Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift

up and out of the workpiece towards the operator.

8) Causes of kickback

a) When the blade is pinched or bound tightly by the kerf

closing in, the blade stalls and the motor reaction drives the

unit rapidly back towards the operator.

b) If the blade becomes twisted or misaligned in the cut,

the teeth at the back edge of the blade can dig into the top

surface of the wood causing the blade to climb out of the kerf

and propel the saw back towards the operator.

Preventing kickback

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided

by taking proper precautions.

a) Maintain a ﬁrm grip with both hands on the saw and

position your body and arms to resist kickback forces.

Kickback forces can be controlled by the operator if proper

precautions are taken.

b) When the blade starts to bind, or when interrupting

a cut for any reason, release the trigger and hold the

saw motionless in the material until the blade comes to

a complete stop. Never attempt to remove the saw from the

work or pull the saw backwards while the blade is in motion.

Investigate and take corrective actions to eliminate the cause

of blade binding.

c) When restarting a saw in the workpiece, centre the saw

blade in the kerf and check that the saw teeth are not

engaged in the material. If the saw blade is binding, the blade

may climb out of the workpiece and kick back as the saw is

restarted.

d) Support large panels to minimise the risk of blade pinching

and kickback. Large panels tend to sag under their own

weight. Supports must be placed under the panel on both sides

of the cut: near the cutline and near the edge of the panel.

e) Do not use a dull or damaged blade. A dull or improperly

sharpened blade produces a narrow kerf, causing excessive

friction, blade binding and kickback.

f) Blade depth and bevel adjusting locks must be tight and

secure before making a cut. If blade adjustment shifts while

cutting, it may cause binding and kickback.

g) Use extra caution when making a plunge cut into existing

walls, ﬂoors or other blind areas. The protruding blade

may come into contact with unseen objects that can cause

kickback.

Guidelines for extension cord use

Extension cords are only to be used for temporary purposes.

They do not replace the need for installation of sockets and

proper wiring where necessary.

In the workshop and on construction sites:

1. Extension cords with an equipment earthing conductor

must be used at all times.

2. Extension cords must be protected from damage, and

not run through doorways or windows where the doors

or windows can close, causing damage to the cord.

3. Extension cords must be a minimum of 16 AWG and be

rated for the equipment in use.

4. Extension cords must be periodically inspected to ensure

that the insulation and conductivity of the wires are not

compromised.

5. Extension cords should not be run through water or

allowed to have connections that may be exposed to

accumulated water.

Produktspezifikationen

Marke:	Kreg
Kategorie:	Sägemaschine
Modell:	Rip-Cut

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kreg Rip-Cut benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Sägemaschine Kreg

Kreg Straight Edge Guide Bedienungsanleitung

12 August 2024

Kreg Rip-Cut Bedienungsanleitung

7 August 2024

Bedienungsanleitung Sägemaschine

Neueste Bedienungsanleitung für -Kategorien-

MSW -TAS287 Bedienungsanleitung

16 Oktober 2024

MSW T-SAW300 Bedienungsanleitung

16 Oktober 2024

Makita 5603 Bedienungsanleitung

15 Oktober 2024

Black And Decker KS650 Bedienungsanleitung

15 Oktober 2024

Royal Catering RCBS-1650 Bedienungsanleitung

15 Oktober 2024

Royal Catering RCBS-1650.1ECO Bedienungsanleitung

15 Oktober 2024

Einhell TC-SM 2131 Dual Bedienungsanleitung

14 Oktober 2024

Einhell TC-AP 650 E Bedienungsanleitung

12 Oktober 2024

Makita DJV181Z Bedienungsanleitung

12 Oktober 2024

Einhell TE-SM 36/210 Li Solo Bedienungsanleitung

11 Oktober 2024