Kramer SKIC-4 Bedienungsanleitung

Kramer Sprecher-Unterstützung SKIC-4

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kramer SKIC-4 (2 Seiten) in der Kategorie Sprecher-Unterstützung. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

SKIC Speaker Mounting Kit

Congratulations on purchasing your Kramer SKIC Speaker Mounting Kit which used for is

securing in-ceiling speakers to the ceiling T-channel grid and comes in three sizes: SKIC-4 for

the Galil 4-CO, SKIC-6 for the Galil 6-CO for the and SKIC-8 Galil 8-CO.

The back can speakers are supported by a C-ring and two tile rails he tile rails prevent the (t

speakers from falling if the tile itself comes out or falls apart, as their ends catch onto the

T-grid). When mounting onto the ceiling tiles, use both supports. When mounting onto a

sheetrock ceiling, the C-ring alone is used to reinforce the ceiling material.

Be sure that the tiles can support the speaker. Smaller sized tiles or ﬁberglass-type tiles cannot

support the weight of the speakers. In such a case, the speakers will require additional support.

Each Speaker Mounting Kit includes: SKIC

Eight support ring screws, washers

and nuts

Two ceiling support rings (C-ring)

Four tile rails

Installing the Speaker Mounting Kit

The is installed after cutting the opening in the ceiling tile for the speakers. SKIC

To install the SKIC, as illustrated in the example in Figure 1, do the following:

1. Place the C-ring over the hole cut in the ceiling tile (on the “ceiling” side). Place it around

the hole so that the tabs located in parallel to the tile edges. are

Figure 1: Installing the Back Can Speakers

2. Place the tile rails the tile and snap them into the two tabs on the C-ring. on

Align the rails so that the ends extend over the T-channel grid.

3. Insert 2 screws through each tab on the C-ring to secure the rails.

4. Push the speaker into the ceiling hole until the front baﬄe rim is leveled with the ceiling.

5. Tighten the mounting tabs (see Figure 2).

When tightening the mounting tabs, the tabs automatically turn outward, thus clamping

the speaker to the wall from its rear side.

Note: Do not over-tighten the mounting tabs. It may cause damage to both the speakers

and the surface.

Figure 2: Tightening the Mounting Tabs

Speciﬁcations

DIMENSIONS:

Tile rails: 64.1cm x 2.2cm x 3cm ( .2 0.2. 25 ” x 0.87” x 97”) W, D, H

21.6cm x 8cm (8.5” x 3.15”)

Model

Outer Diameter

Inner Diameter

SKIC 4

18.5 ( ) cm 7.28”

14.2 cm (5.6”)

SKIC 6

24. 9.532 (cm ”)

20cm (7.9”)

SKIC 8

28.6cm (11.3”)

24.4cm (9.6 ) ”

DISTANCE

BETWEEN FIXING

POINTS:

SKIC 4: 19.1cm (7. ) approx. 5”

SKIC 6: 25.1cm (9. ) approx. 9”

SKIC 8: 29.5cm ( . ) approx.11 6”

WEIGHT OF

MOUNTING KIT

(FOR PAIR):

SKIC 4: 1.03kg (2.27lbs) approx.

SKIC 6: 1.08kg (2. lbs) approx. 38

SKIC 8: 1.14kg (2. lbs) approx. 51

SHIPPING WEIGHT

(FOR PAIR):

SKIC 4: 1.18kg (2.6lbs) approx.

SKIC 6: 1.27kg (2.8lbs) approx.

SKIC 8: 1.36kg (3lbs) approx.

K RAMER ELECT RONICS LT D .

Installation

Instructions

MODELS:

SKIC-4 (for the Galil 4-CO)

SKIC-6 (for the Galil 6-CO)

SKIC-8 (for the Galil 8-CO)

Speaker Mounting Kits

For the latest information on our products and a list of Kramer

distributors, visit our Web site where updates to these installation

instructions may be found.

We welcome y

We welcome yWe welcome your questions, comments, and feedback.

our questions, comments, and feedback.

our questions, comments, and feedback.our questions, comments, and feedback.

Web site: www.kramerelectronics.com

E-mail: info@kramerel.com

SAFETY WARNING

Disconnect the unit from the power

supply before opening and servicing

P/N: 29 00-300440 Rev 2

P/N:

2900- 300440

Rev:

Produktspezifikationen

Marke:	Kramer
Kategorie:	Sprecher-Unterstützung
Modell:	SKIC-4
Produktfarbe:	Silber
Platzierung:	Zimmerdecke
Warentarifnummer (HS):	85189000
Kompatibilität:	Galil 4-CO