König CMP-BARSCAN30 Bedienungsanleitung

König Barcode-Leser CMP-BARSCAN30

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für König CMP-BARSCAN30 (48 Seiten) in der Kategorie Barcode-Leser. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/48

CONTENTS

Getting Started ----------------------------------------------------------

Setup Procedures --------------------------------------------------------

Setup Menu---------------------------------------------------------------

Setup flow Chart --------------------------------------------------------

Group 0 : Interface Selection ----------------------------------------

Group 1 : Device Selection for keyboard interface---------------

6-7

Group 2 : Inter-character Delay -------------------------------------

Group 3 : Language for Keyboard Interface ----------------------

9-10

Group 4 : Terminator--------------------------------------------------

11-12

Group 5 : Scan Mode -------------------------------------------------

13-14

Group 6 : Preamble and Postamble ---------------------------------

Group 7 : Reserved ---------------------------------------------------

Group 8 : RS-232 Parameters ---------------------------------------

16-18

Group 9 : Code 39 / Code 32 ----------------------------------------

19-20

Group 10-1: Interleaved 2 of 5 ---------------------------------------

Group 10-2: Industrial 2 of 5 / IATA---------------------------------

Group 10-3: Matrix 2 of 5----------------------------------------------

Group 10-4: China Postage--------------------------------------------

Group 11 : Code 128/ Code 93/ Code 11/ MSI-PLESSEY------

25-26

Group 12 : ISBN/ISSN-------------------------------------------------

Group 13 : Codabar / NW7--------------------------------------------

Group 14 : Code 4------------------------------------------------------

Group 15-1 : EAN 13 / JAN 13---------------------------------------

Group 15-2 : UPC-A----------------------------------------------------

Group 15-3 : EAN-8 / JAN-8------------------------------------------

Group 15-4 : UPC-E / UCC EAN-128-------------------------------

Group 16 : General Parameters---------------------------------------

Group 17 : Code ID Settings------------------------------------------

Group 18 : Wand Type Parameters----------------------------------

Group 19 : Magnetic Parameters-------------------------------------

37-39

Group 20 : Function Key Emulation---------------------------------

Function Code for PC XT/AT

41-42

Table-Hex : Hexadecimal---

ASCII Table---------------

Hexadecimal-Decimal Conver

Pin Assignments of Scanner

46-47

Getting Started

Installing Keyboard Wedge Scanner

To install a keyboard wedge scanner, follow the steps listed below:

1) Make sure that the scanner has the correct Y (U)- cable for the system (a PC or terminal)

2) Turn off the power of the system

3) Unplug the keyboard from the system

4) Connect the Y (U)- cable to the system and keyboard

5) Turn on the power of the system

6) If the indicator LED lights up and the buzzer sounds, the scanner is ready for reading

Installing a RS-232 Interface Scanner

To install a RS-232 interface scanner, the host device should have a RS-232 port to

receive data from the scanner, follow the steps listed below:

1) Make sure that the scanner has the right connector for the RS-232 port of the host device

2) Make sure that there is a power supply to the scanner (if necessary)

3) Connect the cable to the RS-232 port of the device

4) If the indicator LED lights up and the buzzer sounds, the scanner is ready for reading

Setup Procedures

1) Locate a group that contains the parameters to be changed.

2) Scan the “Enter Group #” label. The scanner will sound beeps indicate that setup is in progress

3) Scan the label representing the parameter to be changed

4) Scan the “Exit” to end the group currently selected, the scanner will sound beeps.

5) Repeat the procedure for other groups including the parameters to be changed

Example 1:

Set the operating mode to “Continuous mode”

1) Scan “Enter Group 5”

2) Scan “Continuous/Trigger off”

3) Scan “Exit”

Example 2

Assign Preamble string as “#”, and postamble string as “END”

1) Scan “Enter Group 6”

2) Scan Preamble”

3) Scan “#” from “Full ASCII Table and Table-Hex.”

4) Scan “Confirm” Label in Table-Hex

5) Scan “Postamble”

6) Scan “E”, “N”, “D” from “Full ASCII Table and Table Hex” consecutively

7) Scan “Confirm” Label in Table-Hex.

8) Scan Exit

Produktspezifikationen

Marke:	König
Kategorie:	Barcode-Leser
Modell:	CMP-BARSCAN30
Gewicht:	160 g
Produktfarbe:	Grau
Betriebstemperatur:	0 - 50 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Zertifizierung:	FCC class A
Gehäusematerial:	ABS Synthetik
Temperaturbereich bei Lagerung:	-20 - 65 °C
Energieverbrauch:	90 mA
Eingebauter Prozessor:	Intel 80C31
Standard-Schnittstellen:	USB
Wellenlänge:	670 nm
Sensor-Typ:	Laser
Stoßfest:	Ja
Lichtlevels (direkt Sonnenlicht):	3000 - 8000 Lux
Scan-Geschwindigkeit:	100 Sekunde/Seite