Klein Tools VDV427-805 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Klein Tools VDV427-805 (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
OPERATING INSTRUCTIONS
Impact Punchdown Tool
(VDV427-013)
Punchdown Multi-Tool
(VDV427-047)
CUT
CUT
INSTRUCCIONES DE OPERACIÓN
Herramienta ponchadora de impacto
(VDV427-013)
Multiherramienta ponchadora
(VDV427-047)
INSTRUÇÕES DE OPERAÇÃO
Ferramenta de Impacto
(VDV427-013)
Ferramenta de impacto multiuso
(VDV427-047)
DIRECTIVES D'UTILISATION
Outil d'insertion Ă  impact
(VDV427-013)
Outil d'insertion de
cĂąble polyvalent
(VDV427-047)
KLEIN TOOLS, INC
Chicago, IL USA
© 2014
110 TYPE PUNCHDOWN INSTRUCTIONS
1. Insert the 110 terminating blade into the punchdown tool.
2. Choose the correct end of the blade depending whether or not the wire is to be cut
off. (Figures 10 & 11 show use of the cutting end).
3. Select the proper force setting – LO for all 110 type connections.
4. Lay the wires in the wire slots (see below).
5. Slide the blade into the wire slot and verify the
orientation of the punchdown blade before moving to step
6 (Figure 10). (This is to avoid cutting wire unintentionally
during the punchdown operation; refer to step 2.)
6. Push down on the cushion-grip end of the punchdown
tool with the palm of your hand until it clicks (Figure 11).
7. Slide the blade out of the wire slot and make sure
the wire is properly seated in the bottom of the wire slot between the insulation
displacement connector’s (IDC) blades.
8. Verify that the punchdown tool has seated the wire completely and correctly in the
IDC. Proper use of the punchdown tool should ensure this is done correctly, but it is
always a good idea to verify and test.
Impact (force)
Setting 66 Panel/Block/
Terminal 110 Cross-connect Panels
/Blocks/Keystones Jacks
LOW
24-26 gauge conductors All
HI
23 and larger
gauge connectors
DO NOT USE
B
56 8
B
A
B
4687
A
66 TYPE PUNCHDOWN INSTRUCTIONS
1. Insert the 66 terminating blade into the punchdown tool.
2. Choose the correct end of the blade depending whether or not the wire is to be cut off.
(Figures 12 & 13 show use of the cutting end).
3. Select the proper force setting depending on the application. (see table below).
4. Lay the wires in the openings on the post, (see below).
5. Slide the blade over the post and verify orientation of
the punchdown blade before moving to step 6 (Figure
12). (This is to avoid cutting the wire unintentionally
during punchdown operation, refer to step 2.)
6. Push down on the cushion-grip end of the
punchdown tool with the palm of your hand until it
clicks (Figure 13).
7. Slide the blade off of the post and make sure the wire is properly seated at the bottom
of the post between the insulation displacement connector’s (IDC)blades.
8. Verify that the punchdown tool has seated the wire completely and correctly in the IDC.
Proper use of the punchdown tool should ensure this is done correctly, but it is always
a good idea to verify and test.
Fig.11
B
A
B
56 8
B
A
4687
B
A
B
56 8
B
A
4687
CUT
CUT
Punchdown tools and accessories
Tool / Blade / (Acc.) Blade / Acc.
Cat. No. Tool with
Blade Cat.No
Impact Punchdown
Tool Chassis
N/A VDV427-013 &
VDV427-047
110 Blade - 110 Cut / 110 Terminate
VDV427-015
VDV427-805
66 Blade - 66 Cut / 66 Terminate
VDV427-016
N/A
66 / 110 Combination Blade
66 Cut / 110 Cut
VDV427-017
VDV427-800 &
VDV427-806
66 / 110 Combination Blade
66 Cut / 110 Cut with
WorkEndsTM
Kit
VDV427-017 & VDV770-
050
†
VDV427-807
DURABLADE
TM
VDV427-104
N/A
WorkEndsTM Kit: Kit includes adapter
and 4 driver bits (#1 and #2 Phillips
and 3/16” and 1/4” Slotted).
VDV770-050 † N/A
ENGLISH ESPAÑOL
Fig.12 Fig.13
INSERTING BLADE
1. Align slot in center of punchdown blade with the pin located on the inside of the
punchdown tool’s barrel and insert blade. (Fig. 1)
2. Rotate blade Œ turn clockwise (Fig. 2).
Note: When blade is completely seated and locked, the cutting knife
(if applicable) should align with the yellow side of the tool; note “CUT” is imprinted
on yellow side of tool.
REMOVING BLADE FROM STORAGE COMPARTMENT
1. Hold the Punchdown Tool with the blade storage end facing down (Fig. 4).
2. Turn the “release blade” dial in a counter-clockwise direction until the blade falls out.
3. Release the “release blade” dial.
ADJUSTING PUNCHDOWN FORCE
Note: Arrow on “Impact” dial aligns with selected force setting.
1. To adjust from LO to HI, rotate dial clockwise (Figure 5).
2. To adjust from HI to LO, rotate the dial counter-clockwise (Figure 6).
Note: See table below for recommended force settings.
PUNCHDOWN MULTI-TOOL SPECIAL
INSTRUCTIONS (VDV427-047):
ENGLISH
Impact (force)
Setting
66 Panel/Block/
Terminal
110 Cross-Connect Panels/
Blocks/Keystones Jacks
Low
24-26 gauge conductors All
HI
23 and larger
gauge connectors
DO NOT USE
REMOVING BLADE
1. Rotate blade Œ turn counter-clockwise and pull gently (Fig. 2).
2. Remove blade (Fig. 1).
Barrel Cross Section Pin
Fig. 1
LOCKING AND UNLOCKING THE IMPACT MECHANISM
To lock, push the locking slide from the “OPEN” position to the “LOCKED” position (Fig. 7).
To unlock, push the locking slide from the “LOCKED” position to the “OPEN” position. (Fig. 8)
PLACING BLADE INTO STORAGE COMPARTMENT
1. Hold the Punchdown Tool with the blade storage end facing up (Fig. 3).
2. Insert the blade into the blade storage end (It will extend beyond the tool).
3. Turn the “release blade” dial in a counter-clockwise direction until the blade slides
into place.
4. Release the “release blade” dial; the blade is now secure in the storage compartment.
Fig. 2 Fig. 3
Fig. 5 Fig. 6Fig. 4


Produktspezifikationen

Marke: Klein Tools
Kategorie: Nicht kategorisiert
Modell: VDV427-805

Brauchst du Hilfe?

Wenn Sie Hilfe mit Klein Tools VDV427-805 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Klein Tools

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-