KitchenAid KWCU205HSS Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr KitchenAid KWCU205HSS (24 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/24
Installation Instructions and
Use and Care Guide
30" (76.2 cm)
36" (91.4 cm)
48" (121.9 cm)
Wall-Mount Canopy Range Hood
IMPORTANT:
Read and save
these instructions.
IMPORTANT:
Installer: Leave Installation Instructions with
the homeowner.
Homeowner: Keep Installation Instructions for
future reference.
Save Installation Instructions for local electrical
inspector's use.
4329224/9763386
Quick Reference
Table of Contents:
Pages
Before you start
Product dimensions
Cabinet dimensions
Venting requirements
Electrical requirements
Installation steps
Use and Care Information
Wiring diagram
Accessories
Warranty
Requesting Assistance or
Service
2
3
3
3
5
5 - 7
8
9
9
10
11 - 12
Before you start...
Proper installation is your
responsibility:
• Have a qualified technician install
this range hood.
• Comply with installation clearances
specified on the model/serial rating
plate.
The model/serial rating plate is
located inside the range hood on the
rear wall.
Range hood location should be away
from strong draft areas, such as
windows, doors and strong heating
vents.
Cabinet opening dimensions that are
shown must be used. Given
dimensions provide minimum
clearance. Consult your cooktop/range
manufacturer installation instructions
before making any cutouts.
Grounded electrical outlet is required.
See “Electrical requirements.”
The canopy hood is factory set for
venting through the roof or wall. For
non-vented (recirculating) installations
see “Non-Vented (Recirculating) Kits”
on the back page.
All openings in ceiling and wall where
range hood will be installed must be
sealed.
Important: Observe all governing
codes and ordinances.
Parts supplied:
4 screws
top
bracket
middle
bracket
bottom
bracket
upper
chimney
canopy
damper
lower
chimney
Parts needed:
2 U.L.- or C.S.A.- listed, 1/2" (12.5 mm)
conduit connectors
power supply cable
1 wall or roof cap
metal vent system
6 screws to attach brackets to wall
Tools needed:
Phillips
screwdriver
flat-blade
screwdriver
caulking gun and
weatherproof
caulking
compound
duct tape
metal
snips
pliers
pencil
saber or
keyhole saw
drill
1-1/4" drill bit
level
measuring
tape or ruler
wire stripper
or utility knife
WARNING — TO REDUCE THE
RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
Installation work and electrical
wiring must be done by qualified
person(s) in accordance with all
applicable Codes and Standards,
including Fire Rated
Construction. The combustion
airflow needed for safe
operation of fuel-burning
equipment may be affected by
this unit’s operation. Follow the
heating equipment
manufacturer’s guideline and
safety standards such as those
published by the National Fire
Protection Association (NFPA),
and the American Society of
Heating, Refrigeration and Air
Conditioning Engineers
(ASHRAE), and the local code
authorities.
When cutting or drilling into wall
or ceiling, do not damage
electrical wiring and other
hidden utilities.
Ducted fans must always be
vented to the outdoors.
WARNING — To reduce the risk
of fire, use only metal ductwork.
This unit must be grounded.
2
This is the safety alert symbol.
This symbol alerts you to
potential hazards that can kill
or hurt you and others. All safety
messages will follow the safety alert
symbol and either the word “DANGER”
or “WARNING”. These words mean:
You can be killed or seriously injured
if you don’t follow instructions.
DANGER
WARNING
Your safety and the safety of
others is very important.
We have provided many important
safety messages in this manual and
on your appliance. Always read and
obey all safety messages.
All safety messages will tell you what
the potential hazard is, tell you how to
reduce the chance of injury, and tell
you what can happen if the
instructions are not followed.
You can be killed or seriously injured
if you don’t immediately follow
instructions.
3
Cabinet dimensionsProduct dimensions
92-1/2"
(235 cm)
min.
111-1/2"
(283.2 cm)
max.
ceiling to
floor
Venting requirements
•The size of the vent should be uniform.
•Use no more than three 90° elbows.
•Make sure there is a minimum of 24" (61 cm) of straight
vent between the elbows if more than one elbow is used.
•Do Not install two elbows together.
•The length of vent system and number of elbows should
be kept to a minimum to provide efficient performance.
•The vent system must have a damper. If roof or wall cap
has a damper, Do Not use damper supplied with the
range hood.
•Use duct tape to seal all joints in the vent system.
•Use caulking to seal exterior wall or roof opening around
the cap.
Determine which venting method is best for your
application and follow “Preparation” under ”Installation
steps“ on Page 5.
For the most efficient and
quiet operation:
Vent system must terminate to the outside.
Do not terminate the vent system in an attic or other
enclosed area.
Do not use 4 inch (10.2 cm) laundry-type wall caps.
Use metal vent only. Rigid metal vent is recommended. Do
not use plastic or metal foil vent.
30" hood 29-15/16" (76 cm),
36" hood 35-3/8" (89.9 cm),
48" hood 47-1/4" (120 cm)
overall width
23" (58.4 cm) min. -
42" (106.7) max.
overall chimney
height
22" (58.9 cm)
lower
chimney
height
1" (2.5 cm) min. -
20" (50.8 cm) max.
upper chimney height
9-1/2" (24.1 cm)
canopy height
19-1/4"
(48.9 cm)
overall depth
5-7/8"
(14.9 cm)
10-7/8"
(27.6 cm)
19" (48.3 cm)*
13" (33 cm)
cabinet
depth
34-5/8"
(87.9 cm)
min.
18" (45.7 cm)
min. clearance
upper cabinet to
countertop
* If the canopy hood is installed higher than
24" (61 cm) above the cooking surface, the
middle bracket must be installed at the
bottom point of the upper chimney sleeve.
** If the canopy hood is mounted higher than
24" (61 cm) above cooking surface, depending
on ceiling height, upper chimney may need to
be cut.
36" (91.4 cm)
base cabinet
height
30" hood 30" (76 cm),
36" hood 35-7/16" (90 cm)
48" hood 47-5/16" (120.2 cm)
min. cabinet opening widths
24" (61 cm) min.
bottom of canopy to
cooking surface**


Produktspezifikationen

Marke: KitchenAid
Kategorie: Nicht kategorisiert
Modell: KWCU205HSS

Brauchst du Hilfe?

Wenn Sie Hilfe mit KitchenAid KWCU205HSS benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert KitchenAid

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-