Kicker ZX500.1 Bedienungsanleitung

Kicker Autoradio ZX500.1

Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r Kicker ZX500.1 (28 Seiten) in der Kategorie Autoradio. Dieser Bedienungsanleitung war fĆ¼r 53 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/28
ZX AMPLIFIER
ZX300.1
ZX400.1
ZX500.1
ZX750.1
English Version
VersiĆ³n EspaƱol
Amplificador del la Serie ZX.1
Deutsche Version
StereoverstƤrker der ZX.1-Serie
Version Francaise
Amplificateur de sƩrie ZX.1
LIVINā€™ LOUD
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 1
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 1
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 1
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 12011 ZX 300.1 400.1 500.1 750.1 RevC.indd 1 11/5/2010 1:22:27 PM
11/5/2010 1:22:27 PM
11/5/2010 1:22:27 PM
11/5/2010 1:22:27 PM11/5/2010 1:22:27 PM
2ZX AMPLIFIERS
ZX.1-SERIES AMPLIFIERS Ownerā€™s Manual
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER ampliļ¬ er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4ā€ (10cm) of open
ventilation for the ampliļ¬ er. If possible, mount the ampliļ¬ er in the climate-controlled passenger compartment. Drill
four holes using a 7/64ā€ (3mm) bit and use the supplied #8 screws to mount the ampliļ¬ er.
Wiring: Disconnect the vehicleā€™s battery to avoid an electrical short. Then, connect the ground wire to the
ampliļ¬ er. Make the ground wire short, 24ā€ (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicleā€™s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batteryā€™s negative post and the vehicle chassis is recommended.
The ZX ampliļ¬ er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereoā€™s source unit. A high-level signal can be run from the source unitā€™s speaker outputs to the
stereo RCA input on the end panel of the ampliļ¬ er using the KICKER ZISL as shown (make sure you set the ZX
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: ZX300.1 ZX400.1 ZX500.1 ZX750.1
RMS Power
@ 14.4V, 4 mono, 1% THD+NĪ©ļ‚£
@ 14.4V, 2 mono, 1% THD+NĪ©ļ‚£
150W x 1
300W x 1
200W x 1
400W x 1
250W x 1
500W x 1
375W x 1
750W x 1
Length 13-1/2ā€
(342mm)
10-1/4ā€
(260mm)
12ā€
(305mm)
14-11/16
(373mm)
Selectable Electronic Crossover Lo-pass,
80Hz,
24dB/octave
Variable lo-pass 50ā€“200Hz, 24dB/octave
Bass Boost +12dB, on/off,
40Hz
Variable 0ā€“18dB @ 40Hz
Frequency Response Ā± 1dB 25Hzā€“20kHz 25Hzā€“200Hz
Speciļ¬ cations common to all models:
Height 2-1/8ā€ (54mm)
Width 9-5/8ā€ (244mm)
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mVā€“5V
High Level: 250mVā€“10V
Subsonic Filter 24dB/octave, ļ¬ xed @ 25Hz
Pro Tip: To get the best performance from your new KICKER Ampliļ¬ er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: ZX300.1 / ZX400.1 / ZX500.1 / ZX750.1
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 2
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 2
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 2
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 22011 ZX 300.1 400.1 500.1 750.1 RevC.indd 2 11/5/2010 1:22:35 PM
11/5/2010 1:22:35 PM
11/5/2010 1:22:35 PM
11/5/2010 1:22:35 PM11/5/2010 1:22:35 PM
3
Model External Fuse Power/Ground Wire KICKER Wiring Kit
ZX300.1 1 x 60 Ampere 8 Gauge PK8, CK8, ZCK8
ZX400.1 1 x 60 Ampere 4 Gauge PK4, CK4, ZCK4
ZX500.1 1 x 80 Ampere 4 Gauge PK4, CK4, ZCK4
ZX750.1 1 x 100 Ampere 4 Gauge PK4, CK4, ZCK4
ampliļ¬ erā€™s input level switch to ā€œHIā€). Alternatively, the signal can be delivered to the ampliļ¬ er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the ampliļ¬ er to ā€œLOā€. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another ampliļ¬ er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to ampliļ¬ er
shield
+
ā€“
core conductor
GND REM +12V
12V
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
ļ‚£18ā€
(45cm)
ļ‚£24ā€
(60cm)
Install a fuse within 18ā€ (45cm) of the battery and in-line with the power cable connected to your ampliļ¬ er. If you
ever need to remove the ampliļ¬ er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the ampliļ¬ er--just the opposite as when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to ampliļ¬ er
protection LED
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 3
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 3
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 3
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 32011 ZX 300.1 400.1 500.1 750.1 RevC.indd 3 11/5/2010 1:22:35 PM
11/5/2010 1:22:35 PM
11/5/2010 1:22:35 PM
11/5/2010 1:22:35 PM11/5/2010 1:22:35 PM


Produktspezifikationen

Marke: Kicker
Kategorie: Autoradio
Modell: ZX500.1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kicker ZX500.1 benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Autoradio Kicker

Bedienungsanleitung Autoradio

Neueste Bedienungsanleitung fĆ¼r -Kategorien-