Kicker zx 350 2 Bedienungsanleitung
Lesen Sie kostenlos die š deutsche Bedienungsanleitung fĆ¼r Kicker zx 350 2 (4 Seiten) in der Kategorie Autoradio. Dieser Bedienungsanleitung war fĆ¼r 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
Ā©2007 Stillwater Designs
ZX
STEREOAMPLIFIER
ZX350.2, ZX450.2, ZX550.2, ZX850.2
+
_
+
+
_
+
_
_
+12V
18"
(45cm)
24"
(60cm)
XOVER
XOVER
XOVER
Installation
1. Mounting Choose a structurally sound location to mount your Kicker ampliļ¬ er. Make sure there
are no items behind the area where the screws will be driven. Choose a location that allows at least
4ā (10cm) of open ventilation for the ampliļ¬ er. If possible, mount the ampliļ¬ er in the climate-controlled
passenger compartment. Drill four holes using a 7/64ā (3mm) bit and use the supplied #8 screws to
mount the ampliļ¬ er.
2. Wiring Disconnect the vehicleās battery to avoid an electrical short. Then, connect the ground wire to
the ampliļ¬ er. Make the ground wire short, 24ā (60cm) or less, and connect it to a paint and corrosion free
solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)
between the battery's negative post and the vehicle chassis is recommended.
The ZX ampliļ¬ er has dual input sensitivity differential RCA inputs which will receive either high or low
level signals from your car stereoās source unit. Ideally, when connecting the source unit to the ampliļ¬ er,
the ZX ampliļ¬ erās input level switch should be set to āLOā and a low-level signal should run from the
source unitās stereo RCA output to the stereo RCA input on the end panel of the ampliļ¬ er using RCA
interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can
be delivered to the ampliļ¬ er using the high-level speaker outputs on the source unit. Set the input level
switch on the end panel of the ampliļ¬ er to āHIā. Crimp and solder RCA connectors to the end of the
speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the
RCA Inputs on the end panel of the ampliļ¬ er as shown in Figure 1. Either input method will provide a
low-level output signal at the RCA output, which effectively passes the audio signal to another ampliļ¬ er
or component. Keep the audio
signal cable away from factory wiring
harnesses and other power wiring. If
you need to cross this wiring, cross it
at a 90 degree angle.
Install a fuse within 18ā (45cm) of the battery and in-line with the 8 gauge power cable connected to your
ampliļ¬ er. If you ever need to remove the ampliļ¬ er from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the ampliļ¬ er--just the opposite as when you installed it.
See the fuse chart on the following page for power and ground wire size, and fusing recommendations.
3. Conļ¬ guration The following diagrams show the most common conļ¬ gurations for your Kicker ZX
series ampliļ¬ er.
ZX.2SeriesAmpliļ¬ er
OwnerāsManual
Tw o ChannelModels: ZX350.2 / ZX450.2 / ZX550.2 / ZX850.2
Authorized Kicker Dealer:
Purchase Date:
Ampliļ¬ er Model Number:
Ampliļ¬ er Serial Number:
Congratulations on your
KICKER purchase!
Please record your purchase
information and keep your sales
receipt for validation of warranty.
__________________________
__________________________
__________________________
__________________________
INSTALLATION
2ZX.2AMPLIFIER
CONFIGURATION
3
+12V
18"
(45cm)
24"
(60cm)
+12V
18"
(45cm)
24"
(60cm)
Figure 2
Figure 3
Figure 4
Minimum Impedance of 2 ohms per channel in stereo operation
Minimum impedance of 4 ohms while in bridged operation
Minimum impedance of 4 ohms mono and 2 ohms per channel in stereo simultaneously
Ground
Remote
Turn-On
Fuse
Battery
High Pass
High Pass
Low Pass
Ground
Remote
Turn-On
Fuse
Battery
Ground
Remote
Turn-On
Fuse
Battery
Signal In
Bridge Wiring
Bridge Wiring
Bridged Operation (Mono)
Two Channel Operation (Stereo)
Stereo and Mono Operation Simultaneously (SAMS)
Note: To get the best performance from your new Kicker Ampliļ¬ er, we recommend using genuine Kicker Accessories and Wiring.
Performance
Model ZX350.2 ZX450.2 ZX550.2 ZX850.2
RMS Power in Watts, all channels driven
@14.4 Volts, 4Ī© stereo, ā¤ 1% THD+N 110 x 2 150 x 2 205 x 2 295 x 2
@ 2Ī© stereo, ā¤ 1% THD+N 175 x 2 225 x 2 275 x 2 425 x 2
@ 4Ī© mono, ā¤ 1% THD+N 350 450 550 850
Length: in(cm) 13 1/2 (34.2) 16 3/4 (42.5) 20 (50.7) 23 1/4 (59)
Speciļ¬ cations common to all models:
Height: in(mm) 2 1/8 (54mm)
Width: in(mm) 9 5/8 (244mm)
Frequency Response, Ā± 0.5 db: 20 Hz - 20 kHz
Signal-to-Noise Ratio: >95db, a-weighted, re: rated power
Input Sensitivity: Low Level: 125mV-5V
High Level: 250mV-10V
Selectable Electronic Crossover: Variable HI, LO or OFF (bypass), 50 - 200Hz, 12db/Octave
Bass Boost: Variable 0-18db Bass Boost @ 40Hz
+
+
>
+
>
Core Cable
Ground or Shielding
High-level Speaker Output Wire
To Ampliļ¬ er
To Source Unit
Figure 1
ModelZX350.2 1 (ONE) 50 AMPERE FUSE PowerGroundWire 8GA
ModelZX450.2 1 (ONE) 60 AMPERE FUSE PowerGroundWire 4GA
ModelZX550.2 1 (ONE) 70 AMPERE FUSE PowerGroundWire 4GA
ModelZX850.2 1 (ONE) 120 AMPERE FUSE PowerGroundWire 2GA
Signal In
Signal Out
Signal In
Signal Out
Signal Out
Operation
1. Automatic Turn-On Selection The ZX series offers three different automatic turn-on modes that can
be selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode
causes the REM terminal to have +12V out for turning on additional ampliļ¬ ers.
īRemote Turn-On Set the switch to +12V to use the remote turn-on lead from your source unit. Run
18 Ga wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the
ampliļ¬ erās positive and negative power terminals. This is the preferred automatic turn-on method.
īDC Offset Turn-On If Remote Turn-On is not an option, the next best setting is DC Offset. The DC
Offset mode detects a 6 volt surge from the HI Level speaker outputs when the source unit has been
turned on.
īSignal Sense Turn-On The Audio setting is the ļ¬ nal alternative for Automatic turn-on. This is a Signal
Sense turn-on method that detects the incoming audio signal from your source unit and automatically
turns on the amp. This turn-on method will not work properly if the input gain control is not set
appropriately.
2. Input Level The RCA inputs on Kicker ZX ampliļ¬ ers are capable of receiving either Hi or Low-level
signals from your source unit. If the only output available from your source unit is a Hi-Level signal, simply
press in the Input Level switch on the ampliļ¬ er. Refer to the wiring section of this manual for additional
instructions.
3. Crossover Switch Use the XOVER switch on the end panel of the ampliļ¬ er to set the internal
crossover to OFF, HI or LO. When the switch is set to OFF, a full bandwidth signal will be ampliļ¬ ed.
Set the switch to HI if you want the ampliļ¬ erās internal crossover to serve as a high-pass ļ¬ lter. Set the
switch to LO if you want the ampliļ¬ erās internal crossover to serve as a low-pass ļ¬ lter. Never change the
crossover āOFF/HI/LOā switch setting with the audio system on!
4. Input Gain Control The input gain control is not a volume control. It matches the output of the
source unit to the input level of the ampliļ¬ er. Turn the source unit up to about 3/4 volume (if the source
unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain on the ampliļ¬ er up until you can hear
audible distortion, then turn it down a little.
5. Bass Boost Control The variable bass boost control on the top of the ampliļ¬ er is designed to give
you increased output 0 - 18dB at 40 Hz. The setting for this control is subjective. If you turn it up, you
must go back and adjust the input gain control to avoid clipping the ampliļ¬ er.
6. Crossover Control The variable crossover on the top of the ampliļ¬ er allows you to adjust the
crossover frequency from 50-200Hz. The setting for this control is subjective; 80Hz is a good place to
start.
7. RemoteBass(Level Control) When the crossover
on your ZX.2 series ampliļ¬ er is set to LO pass, you
have the ability to control the output level of the
ampliļ¬ er remotely. To mount the remote bass level
control, simply screw the metal bracket to the chosen
location. Then slide the housing onto the bracket until
it snaps into place. Run the cable from the controller
to the āRemote Bassā jack on the ampliļ¬ er chassis.
Tr o u b l e Shooting
If your ampliļ¬ er does not appear to be working, check the obvious things ļ¬ rst such as blown fuses,
poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There
is an illuminated red badge on top of the ampliļ¬ er denoting the power state of the amp in addition to
the Protection LED on the end panel of your Kicker ZX series ampliļ¬ er. When the red badge is lit this
indicates the ampliļ¬ er is turned on and the ampliļ¬ er is functioning properly.
OPERATION
ZX.2AMPLIFIER
4
īRED Badge Light off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt
power terminal (should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V)
3) Check for reversed power and ground connections. 4) Ground terminal, for proper conductivity. 5)
Check for blown fuses.
īRED Badge Light on, no output? Check the following: 1) RCA connections 2) Test speaker
outputs with a āknownā good speaker. 3) Substitute source unit with a āknownā good source unit. 4)
Check for a signal in the RCA cable feeding the ampliļ¬ er with the VOM meter set to measure āACā
voltage.
īEnd Panel LED ļ¬ ashing with loud music? The yellow LED indicates low battery voltage. Check
all the connections in your vehicleās charging system. It may be necessary to replace or charge your
vehicleās battery or replace your vehicleās alternator.
īEnd Panel LED on, no output? 1) Ampliļ¬ er is very hot. īThermal protection is engaged. Test
for proper impedance at the speaker terminals with a VOM meter (see the diagrams in this manual
for minimum recommended impedance and multiple speaker wiring suggestions). Also check for
adequate airļ¬ ow around the ampliļ¬ er. 2) Ampliļ¬ er shuts down only while vehicle is running. īVoltage
protection circuitry is engaged. Voltage to the ampliļ¬ er is not within the 9-16 volt operating range. Have
the vehicle's charging and electrical system inspected. 3) Ampliļ¬ er will only play at low volume levels.
īShort circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle
chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended
impedance.
īNo output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or
speaker input) and speaker output connections for the channel 3) Swap the RCA (or speaker input)
cable from left to right. If the problem changes sides then you have a bad RCA (or speaker input) cable
or source unit problem. 4) Swap the speaker output wire from left to right. If the problem changes sides
then you have a bad speaker cable, passive crossover network and/or speaker.
ī Alternator noise-whining sound with engineās RPM? 1) Check for damaged RCA (or speaker
input) cable 2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper
grounding 4) Check the gain settings and turn them down if they are set too high.
īPoor stereo image or reduced bass response? īCheck system phasing by turning the balance
control from left to right. If there is more bass output when turned to either side, then check your speaker
wiring, passive crossover networks and speaker terminals for proper positive and negative connections.
Reverse a speaker connection from positive to negative on the stereo/subwoofer channel(s); if the bass
improves, the speaker was out of phase.
īGround Noise? īKicker ampliļ¬ ers are engineered to be fully compatible with all manufacturersā head
units. Some head units may require additional grounding to prevent noise from entering the audio signal.
If you are experiencing this problem with your head unit, in most cases running a ground wire from the
RCA outputs on the head unit to the chassis will remedy this issue.
Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The Kicker
Coaxial and Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms) and work with
any ampliļ¬ er designed to operate at a four ohm load. If you want to use two Kicker Coaxial or Component speakers on
a single channel of your ampliļ¬ er wire the speakers in series. This will improve the sound quality, lower the total harmonic
distortion and lessen the thermal load at the ampliļ¬ er. This may prevent an ampliļ¬ er from shutting down, due to over-
current protection circuitry.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper
connections can result in blown ampliļ¬ er fuses as well as the failure of other critical systems in the vehicle.
If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER
Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the Kicker
homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab, choose the subject you are interested in, and then
download or view the corresponding information. Please E-mail support@kicker.com or call Technical Services (405) 624-
8583 for unanswered or speciļ¬ c questions.
PERFORMANCE
5
AUTO
TURN ON INPUT
LEVEL
LRL
INPUT OUTPUT
R
XOVER
SPKR+ SPKR -
SPKR + SPKR -
+12V DC
OFFSET
AUDIO LO
HI
OFF HI LO
REMOTE BASS
Model ZX350.2
110 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -94
CEA-2006 (ref: 1W, A-weighted)
Model ZX550.2
205 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -91
CEA-2006 (ref: 1W, A-weighted)
Model ZX450.2
150 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -91
CEA-2006 (ref: 1W, A-weighted)
Model ZX850.2
295 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -89
CEA-2006 (ref: 1W, A-weighted)
AUTO
TURN ON INPUT
LEVEL
LRL
INPUT OUTPUT
R
XOVER
SPKR+ SPKR -
SPKR + SPKR -
+12V DC
OFFSET
AUDIO LO
HI
OFF HI LO
REMOTE BASS
Slide the housing until it snaps into the metal bracket
4 Conductor
Phone Cable
Back View
Side View
Mount the metal bracket
Produktspezifikationen
| Marke: | Kicker |
| Kategorie: | Autoradio |
| Modell: | zx 350 2 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Kicker zx 350 2 benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Autoradio Kicker
29 September 2024
23 September 2024
18 September 2024
16 September 2024
12 September 2024
6 September 2024
31 August 2024
23 August 2024
23 August 2024
22 August 2024
Bedienungsanleitung Autoradio
- Autoradio Clatronic
- Autoradio Sanyo
- Autoradio Manta
- Autoradio Medion
- Autoradio Nedis
- Autoradio Philips
- Autoradio SilverCrest
- Autoradio Sony
- Autoradio Tevion
- Autoradio Panasonic
- Autoradio LG
- Autoradio AEG
- Autoradio Maginon
- Autoradio Denver
- Autoradio ECG
- Autoradio MarQuant
- Autoradio Renkforce
- Autoradio Telefunken
- Autoradio Trevi
- Autoradio Blaupunkt
- Autoradio Grundig
- Autoradio Kenwood
- Autoradio Daewoo
- Autoradio Pyle
- Autoradio Telestar
- Autoradio Aiwa
- Autoradio Auna
- Autoradio Caliber
- Autoradio Lenco
- Autoradio Pioneer
- Autoradio JBL
- Autoradio JVC
- Autoradio KrĆ¼ger And Matz
- Autoradio Muse
- Autoradio Vieta
- Autoradio Hifonics
- Autoradio Akai
- Autoradio Dual
- Autoradio Hyundai
- Autoradio MT Logic
- Autoradio Orava
- Autoradio Orion
- Autoradio Skoda
- Autoradio Varta
- Autoradio Elta
- Autoradio Sencor
- Autoradio Biltema
- Autoradio Mercedes-Benz
- Autoradio Boston Acoustics
- Autoradio Harman Kardon
- Autoradio Magnat
- Autoradio XOMAX
- Autoradio Parrot
- Autoradio Alpine
- Autoradio Volkswagen
- Autoradio Volvo
- Autoradio Opel
- Autoradio MB Quart
- Autoradio Overmax
- Autoradio Rockford Fosgate
- Autoradio Crunch
- Autoradio NextBase
- Autoradio Norauto
- Autoradio AXTON
- Autoradio Clarion
- Autoradio Mac Audio
- Autoradio Conceptronic
- Autoradio Audiovox
- Autoradio Becker
- Autoradio ESX
- Autoradio Zenec
- Autoradio VDO
- Autoradio SPC
- Autoradio Roadstar
- Autoradio TokaĆÆ
- Autoradio Audison
- Autoradio Macrom
- Autoradio Phonocar
- Autoradio Xblitz
- Autoradio Autovision
- Autoradio Boss
- Autoradio Hertz
- Autoradio Renault
- Autoradio Fiat
- Autoradio Jensen
- Autoradio DLS
- Autoradio Eclipse
- Autoradio Eltax
- Autoradio Emphaser
- Autoradio Focal
- Autoradio Fusion
- Autoradio Ground Zero
- Autoradio Helix
- Autoradio Impulse
- Autoradio Lanzar
- Autoradio Mtx Audio
- Autoradio Naxa
- Autoradio Revo
- Autoradio Rodek
- Autoradio RTO
- Autoradio Sevic
- Autoradio Sirius
- Autoradio Soundstream
- Autoradio Spectron
- Autoradio Stinger
- Autoradio Tamashi
- Autoradio Toxic
- Autoradio Twister
- Autoradio Ultimate
- Autoradio US Blaster
- Autoradio VDO Dayton
- Autoradio Voxx
- Autoradio VW
- Autoradio Watssound
- Autoradio RetroSound
- Autoradio Kunft
- Autoradio Multilaser
- Autoradio Brigmton
- Autoradio Lark
- Autoradio Majestic
- Autoradio SoundMAX
- Autoradio Scion
- Autoradio Raveland
- Autoradio Planet Audio
- Autoradio Adcom
- Autoradio Sendai
- Autoradio Cartronix
- Autoradio Dension
- Autoradio Mystery
Neueste Bedienungsanleitung fĆ¼r -Kategorien-
16 Oktober 2024
16 Oktober 2024
12 Oktober 2024
12 Oktober 2024
8 Oktober 2024
7 Oktober 2024
7 Oktober 2024
6 Oktober 2024
5 Oktober 2024
5 Oktober 2024