Kicker KX800.1 Bedienungsanleitung

Kicker Autoradio KX800.1

Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r Kicker KX800.1 (28 Seiten) in der Kategorie Autoradio. Dieser Bedienungsanleitung war fĆ¼r 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/28
Ownerā€™s Manual |
Manual del Propietario |
Benutzerhandbuch |
Manuel dā€™utilisation |
KX Amplifiers
2013 KX Mono Amps Rev G.indd 1
2013 KX Mono Amps Rev G.indd 1
2013 KX Mono Amps Rev G.indd 1
2013 KX Mono Amps Rev G.indd 12013 KX Mono Amps Rev G.indd 1 11/13/2012 2:13:57 PM
11/13/2012 2:13:57 PM
11/13/2012 2:13:57 PM
11/13/2012 2:13:57 PM11/13/2012 2:13:57 PM
2
KX.1-SERIES AMPLIFIERS
OWNERā€™S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER ampliļ¬ er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4ā€ (10cm) of open
ventilation for the ampliļ¬ er. If possible, mount the ampliļ¬ er in the climate-controlled passenger compartment. Drill
four holes using a 7/64ā€ (3mm) bit and use the supplied #8 screws to mount the ampliļ¬ er.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: KX400.1 KX800.1 KX1200.1 KX1600.1 KX2400.1
RMS Power
@ 14.4V, 4 1% THD+NĪ© mono, ļ‚£
@ 14.4V, 2 mono, 1% THD+NĪ©ļ‚£
200W x 1
400W x 1
400W x 1
800W x 1
600W x 1
1200W x 1
800W x 1
1600W x 1
1200W x 1
2400W x 1
Length | in [cm] 8 [20.4] 9 9/16 [24.4] 9 9/16 [24.4] 11 3/16 [28.4] 15 1/2 [39.4]
Speciļ¬ cations common to all models:
Height | in [cm] 2 1/8 [5.5]
Width | in [cm] 8 5/16 [21]
Frequency Response Ā± 1dB 10Hzā€“160Hz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mVā€“5V
High Level: 250mVā€“10V
Electronic Crossover Variable Lo-pass 40Hzā€“160Hz, 24dB/octave
Bass Boost Parametric 20-80Hz; Variable Q: 1 to 5; Variable Boost, 0-18dB
Subsonic Filter Variable 10ā€“80Hz, 24dB/octave
Remote Bass Yes [included]
Pro Tip: To get the best performance from your new KICKER Ampliļ¬ er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: KX400.1 / KX800.1 / KX1200.1 / KX1600.1 / KX2400.1
2013 KX Mono Amps Rev G.indd 2
2013 KX Mono Amps Rev G.indd 2
2013 KX Mono Amps Rev G.indd 2
2013 KX Mono Amps Rev G.indd 22013 KX Mono Amps Rev G.indd 2 11/13/2012 2:17:11 PM
11/13/2012 2:17:11 PM
11/13/2012 2:17:11 PM
11/13/2012 2:17:11 PM11/13/2012 2:17:11 PM
3
Wiring: Disconnect the vehicleā€™s battery to avoid an electrical short. Then, connect the ground wire to the
ampliļ¬ er. Make the ground wire short, 24ā€ (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicleā€™s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batteryā€™s negative post and the vehicle chassis is recommended.
The KX ampliļ¬ er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereoā€™s source unit. A high-level signal can be run from the source unitā€™s speaker outputs to the
stereo RCA input on the end panel of the ampliļ¬ er using the KICKER ZISL as shown (make sure you set the KX
ampliļ¬ erā€™s input level switch to ā€œHIā€). Alternatively, the signal can be delivered to the ampliļ¬ er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the ampliļ¬ er to ā€œLOā€. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another ampliļ¬ er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to ampliļ¬ er
shield
+
+
+
ā€“ā€“
ā€“
core conductor KICKER ZISL (optional)
source unit high-level
speaker outputs
OR to ampliļ¬ er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KX400.1 1 x 60 Ampere 4 Gauge PK4, CK44, ZCK44
KX800.1 1 x 100 Ampere 4 Gauge PK4, CK44, ZCK44
KX1200.1 1 x 150 Ampere 1/0 Gauge PKD1, PWB050
KX1600.1 1 x 150 Ampere 1/0 Gauge PKD1, PWB050
KX2400.1 1 x 200 Ampere 1/0 Gauge PKD1, PWB050
Install a fuse within 18ā€ (45cm) of the battery and in-line with the power cable connected to your ampliļ¬ er. If you
ever need to remove the ampliļ¬ er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the ampliļ¬ er--just the opposite as when you installed it.
2013 KX Mono Amps Rev G.indd 3
2013 KX Mono Amps Rev G.indd 3
2013 KX Mono Amps Rev G.indd 3
2013 KX Mono Amps Rev G.indd 32013 KX Mono Amps Rev G.indd 3 11/13/2012 2:17:12 PM
11/13/2012 2:17:12 PM
11/13/2012 2:17:12 PM
11/13/2012 2:17:12 PM11/13/2012 2:17:12 PM


Produktspezifikationen

Marke: Kicker
Kategorie: Autoradio
Modell: KX800.1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kicker KX800.1 benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Autoradio Kicker

Bedienungsanleitung Autoradio

Neueste Bedienungsanleitung fĆ¼r -Kategorien-