Kicker Klock Werks RVICXCT10 Bedienungsanleitung

Kicker Hi-Fi-Anlage Klock Werks RVICXCT10

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kicker Klock Werks RVICXCT10 (23 Seiten) in der Kategorie Hi-Fi-Anlage. Dieser Bedienungsanleitung war für 28 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/23
Victory
Cross
Country
Rear
amp/speaker installation
*Please reference model appropriate manual
for
procedures and
torque
specifications
1. Protect painted surfaces
with
a soft cloth
2.
Remove inner chin fairing and disconnect battery
Harness installation
1. Follow proper procedure
to
remove:
a.
Seat
b.
Fuel
tank
c.
Side covers
d.
Lower backrest pad
e.
Rear speakers
f.
Rear
speaker housings
2.
Disconnect
the
2-pin
power
harness under
the
left
side cover
(Red
and Black wires)
3.
From
the
inside-left
of
the
trunk, thread
the
left
side speaker wires, blue trigger
wire
and
power
leads through
the
existing holes behind
the
left
side speaker
PIC
4.
Route the
power
leads along
the
existing
trunk
harness and under
the
left
side cover
5.
Route
the
blue trigger wire under the
lower
backrest area and connect
it
to
the
blue/pink
wire
with
the barrel connector
PIC
6.
Route
the
right speaker wires along
the
floor
of
the
trunk
and through a hole behind
the
right speaker
PIC
Speaker installation
1. Install
the
rear speaker housings back
onto
the
trunk
ensuring correct wire routing
to
avoid pinching
2.
Left side speaker
a.
Install a piece
of
heat shrink over
the
male ends
of
the
amp harness and connect
them
to
the
stock speaker terminals. Activate heat shrink over connections
to
reduce
the
risk
of
a short
b.
Connect
the
female ends from
the
amplifier harness
to
the
new
speaker
from
the
kit
c.
Carefully
fit
speaker
into
the
housing and reinstall original hardware
3.
Repeat
for
right side speaker
Amp installation
1. Install amplifier
onto
bracket using supplied hardware
PIC
2.
Remove
the
black
8mm
fastener in
the
front
left
of
the
trunk
floor, place
the
amp and
bracket assembly over
that
hole and loosely reinstall
the
black
8mm
fastener
PIC
3.
Connect
the
harness
to
the
amplifier
4. Tuck any excess wire length into
the
speaker pods
5. Remove
the
black 8mm fastener from
the
front
right
of
the
trunk
floor
and install
supplied
P-el
amp
to
retain
the
right side
of
the
harness
PIC
6. Positioning
the
amp bracket over
the
holes
for
the
lower
backrest, reinstall
the
backrest
using
the
original hardware
7. Torque all three amp bracket fasteners
8.
Reconnect
the
2-pin
power
harness and
the
battery
to
check system operation
Note: At this time,
it
is
highly recommended
to
follow
the
guidelines in
your
Kicker
PX
100.2
owner's manual
to
set up
the
amplifier. Klock Werks recommends
that
the
dip switches be set
up
as
follows:
1.
Auto
turn-on
- 12V
2.
Input
level -
HI
3. HI-PASS-
OFF
4.
Input
Gain
control-
Follow
the
instructions in your Kicker
PX
100.2 owner's manual
Pg.4
9.
Disconnect
the
battery
and carefully reassemble motorcycle
10. Reconnect
the
battery, assemble
the
chin fairing and enjoy
your
Kicker audio system!
KICKER AMP SPEAKER&
INSTALLATION GUIDE
FOR USE WITH VICTORY CROSS COUNTRY TRUNK
> Step-by-step Installation Guide
> 5 1/4 Kicker Speakers Pair
> Kicker Amp 100W/50W
> Stainless Steel Mounting Bracket
> Custom Wiring Harness
> Black Heat Shrink
> Black Cable Tie
> All Necessary Hardware
- 8 - 32 x 1/2” Button Head Bolts
- 8 - 32 Nylock Nuts
INCLUDED IN THIS FIT KIT:


Produktspezifikationen

Marke: Kicker
Kategorie: Hi-Fi-Anlage
Modell: Klock Werks RVICXCT10

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kicker Klock Werks RVICXCT10 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Hi-Fi-Anlage Kicker

Bedienungsanleitung Hi-Fi-Anlage

Neueste Bedienungsanleitung für -Kategorien-