Kicker IX500.4 Bedienungsanleitung

Kicker Autoradio IX500.4

Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r Kicker IX500.4 (28 Seiten) in der Kategorie Autoradio. Dieser Bedienungsanleitung war fĆ¼r 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/28
IX AMPLIFIER
IX500.4
English Version
VersiĆ³n EspaƱol
Amplificador del la Serie IX.4
Deutsche Version
StereoverstƤrker der IX.4-Serie
Version Francaise
Amplificateur de sƩrie IX.4
LIVINā€™ LOUD
2IX AMPLIFIERS
IX.1-SERIES AMPLIFIERS Ownerā€™s Manual
IX500.4
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER ampliļ¬ er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4ā€ (10cm) of open
ventilation for the ampliļ¬ er. If possible, mount the ampliļ¬ er in the climate-controlled passenger compartment.
Drill four holes using a 7/64ā€ (3mm) bit and use the supplied #8 screws to mount the ampliļ¬ er. Use the IXSM
mounting bracket (sold separately) to stack IX ampliļ¬ ers of different sizes.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Serial Number:
Model: IX500.4
RMS Power
@ 14.4V, 4 stereo, 1% THD+NĪ©ļ‚£
@ 14.4V, 2 stereo, 1% THD+NĪ©ļ‚£
@ 14.4V, 4 mono, 1% THD+NĪ©ļ‚£
75W x 4
125W x 4
250W x 2
Length 11-3/8ā€ (288mm)
Height 2-3/16ā€ (55mm)
Width 7-7/8ā€ (200mm)
Frequency Response Ā± 1dB 20Hzā€“20kHz
Signal-to-noise Ratio 98dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mVā€“5V
High Level: 250mVā€“10V
Electronic Crossover Selectable HI/LO/OFF, Variable lo-pass 50ā€“200Hz,
12dB/octave
Bass Boost Variable 0ā€“18dB @ 40Hz
Maximum Efļ¬ ciency (2Ī©) >80%
Pro Tip: To get the best performance from your new KICKER Ampliļ¬ er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
IXSM
sold separately
3
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
IX500.4 2 x 50 Ampere 4 Gauge PK4, CK4, ZCK4
Wiring: Disconnect the vehicleā€™s battery to avoid an electrical short. Then, connect the ground wire to the
ampliļ¬ er. Make the ground wire short, 24ā€ (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicleā€™s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batteryā€™s negative post and the vehicle chassis is recommended.
The IX ampliļ¬ er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereoā€™s source unit. Ideally, when connecting the source unit to the ampliļ¬ er, the IX ampliļ¬ erā€™s input
level switch should be set to ā€œLOā€ and a low-level signal should run from the source unitā€™s stereo RCA output to
the stereo RCA input on the end panel of the ampliļ¬ er using RCA interconnect cable. If a low-level stereo RCA
output is not available on the source unit, the signal can be delivered to the ampliļ¬ er using the high-level speaker
outputs on the source unit. Set the input level switch on the end panel of the ampliļ¬ er to ā€œHIā€. Crimp and solder
RCA connectors to the end of the speaker wire running from the high-level speaker outputs on the source unit
and connect the wire to the RCA Inputs on the end panel of the ampliļ¬ er or simplify the installation by using a
KICKER ZISL as shown below. Either input method will provide a low-level output signal at the RCA output, which
effectively passes the audio signal to another ampliļ¬ er or component. Keep the audio signal cable away from
factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to ampliļ¬ er
shield
+
ā€“
core conductor
Install a fuse within 18ā€ (45cm) of the battery and in-line with the power cable connected to your ampliļ¬ er. Install
a second fuse within 18ā€ (45cm) of the ampliļ¬ er. If you ever need to remove the ampliļ¬ er from the vehicle after it
has been installed, the ground wire should be the last wire disconnected from the ampliļ¬ er--just the opposite as
when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to ampliļ¬ er
INPUT
LEVEL
LO
HI
AMP2AMP1
L
R
OUTPUT
POWERAMP1
GNDL+ Lā€“ R+ Rā€“ REM +12V
AUTO
TURN ON
12V DC AUDIO
OFFSET
FADER
OFF
ON
BRIDGED
AMP2
L+ Lā€“ R+ Rā€“
BRIDGED
12V
ļ‚£18ā€
(45cm)
battery
external fuse
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
ļ‚£24ā€
(60cm)


Produktspezifikationen

Marke: Kicker
Kategorie: Autoradio
Modell: IX500.4

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kicker IX500.4 benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Autoradio Kicker

Bedienungsanleitung Autoradio

Neueste Bedienungsanleitung fĆ¼r -Kategorien-