Kicker DX300 2 Bedienungsanleitung

Kicker Autoradio DX300 2

Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r Kicker DX300 2 (28 Seiten) in der Kategorie Autoradio. Dieser Bedienungsanleitung war fĆ¼r 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/28
DX AMPLIFIER
D
LIVINā€™ LOUD
2011 DX Stereo Amps RevD.indd 1
2011 DX Stereo Amps RevD.indd 1
2011 DX Stereo Amps RevD.indd 1
2011 DX Stereo Amps RevD.indd 12011 DX Stereo Amps RevD.indd 1 11/3/2010 12:29:22 PM
11/3/2010 12:29:22 PM
11/3/2010 12:29:22 PM
11/3/2010 12:29:22 PM11/3/2010 12:29:22 PM
2
DX.2-SERIES AMPLIFIERS
OWNERā€™S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER ampliļ¬ er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4ā€ (10cm) of open
ventilation for the ampliļ¬ er. If possible, mount the ampliļ¬ er in the climate-controlled passenger compartment. Drill
four holes using a 7/64ā€ (3mm) bit and use the supplied #8 screws to mount the ampliļ¬ er.
Wiring: Disconnect the vehicleā€™s battery to avoid an electrical short. Then, connect the ground wire to the
ampliļ¬ er. Make the ground wire short, 24ā€ (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicleā€™s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batteryā€™s negative post and the vehicle chassis is recommended.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: DX125.2 DX300.2
RMS Power
@ 14.4V, 4 stereo, 1% THD+NĪ©ļ‚£
@ 14.4V, 2 stereo, 1% THD+NĪ©ļ‚£
@ 14.4V, 4 mono, 1% THD+NĪ©ļ‚£
30W x 2
60W x 2
125W x 1
75W x 2
150W x 2
300W x 1
Length, in. (cm) 8-1/4ā€ (21) 12-1/4ā€ (31)
Electronic Crossover 18dB/Octave High Pass Fixed
@ 100Hz, 18dB/Octave Low
Pass Fixed @ 80Hz
12dB/Octave, variable
50Hz-200Hz, selectable
HI, LO and OFF
Bass Boost Selectable 0/9dB @ 40Hz Variable 0ā€“12dB @ 40Hz
Speciļ¬ cations common to all models:
Height, in. (mm) 2-1/4ā€ (57)
Width, in. (mm) 8-5/16ā€ (211)
Frequency Response Ā± 1dB 20Hzā€“20KHz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mVā€“5V
High Level: 250mVā€“10V
Pro Tip: To get the best performance from your new KICKER Ampliļ¬ er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: DX125.2 / DX300.2
2011 DX Stereo Amps RevD.indd 2
2011 DX Stereo Amps RevD.indd 2
2011 DX Stereo Amps RevD.indd 2
2011 DX Stereo Amps RevD.indd 22011 DX Stereo Amps RevD.indd 2 11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM11/3/2010 12:29:28 PM
3
12V
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
DX125.2 1 x 40 Ampere 8 Gauge PK8, ZCK84
DX300.2 1 x 60 Ampere 8 Gauge PK8, ZCK84
The DX ampliļ¬ er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereoā€™s source unit. A high-level signal can be run from the source unitā€™s speaker outputs to the
stereo RCA input on the end panel of the ampliļ¬ er using the KICKER ZISL as shown (make sure you set the DX
ampliļ¬ erā€™s input level switch to ā€œHIā€). Alternatively, the signal can be delivered to the ampliļ¬ er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the ampliļ¬ er to ā€œLOā€. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another ampliļ¬ er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to ampliļ¬ er
shield
+
ā€“
core conductor
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
ļ‚£18ā€
(45cm)
ļ‚£24ā€
(60cm)
Install a fuse within 18ā€ (45cm) of the battery and in-line with the power cable connected to your ampliļ¬ er. If you
ever need to remove the ampliļ¬ er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the ampliļ¬ er--just the opposite as when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to ampliļ¬ er
2011 DX Stereo Amps RevD.indd 3
2011 DX Stereo Amps RevD.indd 3
2011 DX Stereo Amps RevD.indd 3
2011 DX Stereo Amps RevD.indd 32011 DX Stereo Amps RevD.indd 3 11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM11/3/2010 12:29:28 PM


Produktspezifikationen

Marke: Kicker
Kategorie: Autoradio
Modell: DX300 2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kicker DX300 2 benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Autoradio Kicker

Bedienungsanleitung Autoradio

Neueste Bedienungsanleitung fĆ¼r -Kategorien-