Kicker CX1200.1 Bedienungsanleitung

Kicker Autoradio CX1200.1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kicker CX1200.1 (28 Seiten) in der Kategorie Autoradio. Dieser Bedienungsanleitung war für 49 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/28

Owner’s Manual |

Manual del Propietario |

Benutzerhandbuch |

Manuel d’utilisation |

CX Amplifiers

2012 CX Mono Amps Rev I.indd 1

2012 CX Mono Amps Rev I.indd 12012 CX Mono Amps Rev I.indd 1 6/22/2012 2:32:04 PM

6/22/2012 2:32:04 PM

6/22/2012 2:32:04 PM6/22/2012 2:32:04 PM

CX.1-SERIES AMPLIFIERS

OWNER’S MANUAL

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER ampliﬁ er. Make sure there are no items

behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open

ventilation for the ampliﬁ er. If possible, mount the ampliﬁ er in the climate-controlled passenger compartment. Drill

four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the ampliﬁ er.

The KICKER CX Ampliﬁ ers are capable of space-saving vertical mounting. Use a 2.5mm hex key (Allen wrench)

to loosen the endpanel, remove the existing brackets, then insert and tighten the double-slotted brackets to the

ampliﬁ er as illustrated on the next page.

PERFORMANCE

Authorized KICKER Dealer:

Purchase Date:

Model Number:

Serial Number:

Model: CX300.1 CX600.1 CX1200.1

RMS Power

@ 14.4V, 4 1% THD+NΩ mono, 

@ 14.4V, 2 mono, 1% THD+NΩ

150W x 1

300W x 1

600W x 1

1200W x 1

Length | in [mm] 8-1/8 [210] 8-1/8 [210] 12-1/16 [310]

Speciﬁ cations common to all models:

Height | in [mm] 2-3/8 [60]

Width | in [mm] 7-3/16 [180]

Frequency Response ± 1dB 25Hz–200Hz

Signal-to-noise Ratio >95dB, A-weighted, re: rated power

Input Sensitivity Low Level: 125mV–5V

High Level: 250mV–10V

Electronic Crossover Variable Lo-pass 50Hz–200Hz, 12dB/octave

Bass Boost Variable 0–12dB @ 40Hz

Subsonic Filter 25Hz, 24dB/octave

Remote Bass Yes [sold separately]

Pro Tip: To get the best performance from your new KICKER Ampliﬁ er and extend the warranty by 1 year, use

genuine KICKER accessories and wiring.

MODEL: CX300.1 / CX600.1 / CX1200.1

2012 CX Mono Amps Rev I.indd 2

2012 CX Mono Amps Rev I.indd 22012 CX Mono Amps Rev I.indd 2 6/22/2012 2:32:28 PM

6/22/2012 2:32:28 PM

6/22/2012 2:32:28 PM6/22/2012 2:32:28 PM

Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the

ampliﬁ er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,

metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the

battery’s negative post and the vehicle chassis is recommended.

The CX ampliﬁ er has dual input sensitivity differential RCA inputs which will receive either high or low level signals

from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the

stereo RCA input on the end panel of the ampliﬁ er using the KICKER ZISL as shown (make sure you set the CX

ampliﬁ er’s input level switch to “HI”). Alternatively, the signal can be delivered to the ampliﬁ er using the low-level

RCA outputs on the source unit. Set the input level switch on the end panel of the ampliﬁ er to “LO”. Either input

method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to

another ampliﬁ er or component. Keep the audio signal cable away from factory wiring harnesses and other

power wiring. If you need to cross this wiring, cross it at a 90 degree angle.

source unit

high-level speaker

outputs

to ampliﬁ er

shield

double-slotted

bracket

––

–

core conductor KICKER ZISL (optional)

source unit high-level

speaker outputs

OR to ampliﬁ er

VERTICAL MOUNTING

hex screws

ampliﬁ er side panel

2012 CX Mono Amps Rev I.indd 3

2012 CX Mono Amps Rev I.indd 32012 CX Mono Amps Rev I.indd 3 6/22/2012 2:32:29 PM

6/22/2012 2:32:29 PM

6/22/2012 2:32:29 PM6/22/2012 2:32:29 PM

Produktspezifikationen

Marke:	Kicker
Kategorie:	Autoradio
Modell:	CX1200.1
Breite:	161.8 mm
Tiefe:	163.1 mm
Produktfarbe:	Schwarz
Höhe:	86 mm
Rauschverhältnis (SNR):	95 dB
Anzahl der Verstärkerkanäle:	1 Kanäle
RMS Leistungsoutput pro Kanal (2 Ohm):	1200 W
RMS Leistungsoutput pro Kanal (4 Ohm):	600 W
Tiefpassfilterbereich:	50 - 200 Hz
Bass-Boost:	0 - 12 dB
Eingang Empfindlichkeit:	250 mV
Hochpassfilterbereich:	25 - 200 Hz