Khind WH803 Bedienungsanleitung

Khind Kessel & Heizkessel WH803

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Khind WH803 (13 Seiten) in der Kategorie Kessel & Heizkessel. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/13

model / 型号 WH803 & WH903P

P/N: 40-50582-00

Water Heater / / 电热水器 Pemanas Air

Instruction Manual / Buku Panduan说明指示书 /

Please read this manual carefully before operating this product. Keep this manual handy for further reference.

请在使用此产品前,详读此说明书。并将之收藏以作日后参考。

Sila baca buku panduan ini dengan teliti sebelum menggunakan produk ini. Simpanlah untuk rujukan masa depan.

Important / / Mustahak重要

This manual is also available online.

www.khind.com.my

Model

Voltage

Heater Power

Pump Type

Pump Power rating

Noise Level

Water Connection

Operating Connection

Protection Against Electric Shock

Degree of Protection

Minimum Water Flow Rate

Minimum Water Pressure

Maximum Water Pressure

Product Dimension (WxLxH)

Net Weight (kg)

WH803

240V~ 50/60Hz

3.75kW

15mm (1/2" BSP),

Single Point System

Open Outlet

Class I

IP25

3 Litres / minute

20 kPa (0.2 bar/ 2.9 psi)

0.3 Mpa (3bar/43.5psi)

340x240x95mm

1.8kg

WH903P

240V~ 50/60Hz

3.75kW

DC Pump

50W

<40dB

15mm (1/2" BSP),

Single Point System

Open Outlet

Class I

IP25

3 Litres / minute

20 kPa (0.2 bar/ 2.9 psi)

0.3 Mpa (3bar/43.5psi)

340x240x95mm

2.5kg

Specifications

*Specifications are subject to change without prior notice.

Schematic diagram

Parts identification

1. Power ON Indicator

2. ELSD ON Indicator

3. Power/Temperature Control Knob

4. ELSD Test Button

5. ELSD Reset Button

6. Shower Head

7. Shower Rail

8. Shower Hose

9. Filter Valve

10. Flow Regulator Valve

11. Pump ON/OFF Button (for WH903P only)

12. Pump Indicator (for WH903P only)

a. 2-in-1 Manual Reset Thermal-cut-out

& Thermostat

b. Thermistor

c. Heater Tank

d. PCB (Indicator)

e. PCB (ELSD)

f. PCB (Push Button & Control)

g. Flow Switch

h. Triac

i. Cable Clip

j. Terminal Block

k. Pump (for WH903P)

External Parts Identification

Internal Parts Identification

WH803 WH903P

WH903P (DC Pump)WH803

Cleaning & maintenance

Clean filters regularly

Remove the Regulator Valve Insert from the regulator valve assembly. Take out the

Filter Plate Unit as shown and flush it with water to remove any trapped particle. Slot

back the Filter Plate Unit to its original position and secure it.

Adjustment of Regulator Valve

Turn the knob clockwise to have the maximum water volume in low water pressure

areas. In high water pressure areas, turn the knob anticlockwise until the desired

shower temperature is attained.

General Maintenance

• DO NOT use thinner, alcohol or petrol.

Clean the heater with a damp cloth and mild detergent but do not use thinner, alcohol, petrol or any other

organic solution.

• Shower head must be periodically clean to ensure no blockage occurred.

• Check and clean the filter mesh inside the regulator valve regulary.

This is continuous-flow instantaneous water heater. Flow-controlled and designed to withstand the full main

pressure, and the continuous flow instantaneous water heater will supply hot water whenever you need it.

The main features of our continuous flow water heaters are:

• High energy conversion efficiency

• Small size

• Point-of use installation for single tap connection

General product information

1. Please read this manual thoroughly and understand the content before use.

2. Check if the main supply voltage is matched with the voltage stated on the rating plate of the water heater.

3. Installation of water heater must be carried out by an authorised or qualifed technician.

4. DO NOT attempt to repair the water heater without qualified technician.

5. DO NOT switch on the water heater if there is a possibility that the water in the heater is frozen.

6. DO NOT install INLET & OUTLET of water heater reversely.

7. DO NOT install the water heater where there is consistent spray directly over the unit.

8. DO NOT connect the OUTLET to any tap or fitting that is not recommended by the manufacturer.

9. DO NOT block the water heater outer in any way.

10. The spray head (shower head) must be descaled regularly.

11. To ensure perfect functioning of the heater, certain minimum water flow level must be guaranteed

(Refer Product Specification).

12. Separate electric circuits must be provided for the water heater.

13. Test water temperature with hand before using the the water heater. Be careful to avoid scalding by hot

water.

14. Check the ELSB once a month and consult professional for repair if there is any malfunction.

15. Metallic/chromed flexible hose and conductive control valve shall not be used.

16. This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the

appliance.

17. DO NOT leave the hand shower idle in the pail.

18. Do not use plumbing cement on connection. If necessary, use only

thread or sealing tape.

19. This appliance must be earthed.

20. This appliance is intended for household use only. Not for commercial use

or outdoor use.

21. It is forbidden to place flammable and explosive materials near the water heater.

22. Please install the water heater on a secure and solid wall.

Safety precaution

Installation

General Installation Instructions

1. Installation must be carried out by a qualified electrician with close reference to the operation manual and

in compliance with the local regulations.

2. The water heater must only be installed and operated in a room free from frost.

3. The screws and wall plugs required for mounting the water heater are included in the delivery.

Note: The control knob(s) are integral part of the cover, do not attempt to remove them.

4. Mark mounting position

• Unscrew the bottom retained screw and lift the cover from the back plate.

• Use the back plate as the template and mark the three fixing holes.

• Drill the holes and insert the wall plugs.

• Insert the cables through the cable entry of the water heater.

• Fit the water heater to the secure solid wall.

Heater INLET and OUTLET Connection

1. All the plumbing works should be completed

before proceeding to electrical wiring connection.

2. INLET and OUTLET connection of the heater

unit should not be reversed, with Flow

Regulator Valve Assembly installed on INLET.

!CAUTION:

THIS APPLIANCE MUST BE EARTHED.

OUTLET INLET

Flow Regulator Valve Assembly

installed on INLET

Bottom View

Produktspezifikationen

Marke:	Khind
Kategorie:	Kessel & Heizkessel
Modell:	WH803

Brauchst du Hilfe?

Wenn Sie Hilfe mit Khind WH803 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Kessel & Heizkessel Khind

Khind KRS101 Bedienungsanleitung

5 September 2024

Khind WH802 Bedienungsanleitung

5 September 2024

Khind WH903P Bedienungsanleitung

5 September 2024

Khind WH803 Bedienungsanleitung

5 September 2024

Bedienungsanleitung Kessel & Heizkessel

Neueste Bedienungsanleitung für -Kategorien-

Sencor SWK 7706GD Bedienungsanleitung

14 Oktober 2024

Hotpoint HE30S01SAG Bedienungsanleitung

14 Oktober 2024

Tesy ModEco Electronic 50 Bedienungsanleitung

11 Oktober 2024

Junkers KBR 280-3 A Bedienungsanleitung

10 Oktober 2024

Ariston Thermo MicroGenus HE 32 MFFI Bedienungsanleitung

7 Oktober 2024

Elco Vistron H 500 Bedienungsanleitung

5 Oktober 2024

Worcester Greenstar 12i System Bedienungsanleitung

4 Oktober 2024

Nibe MT-WH21-019-FS Bedienungsanleitung

4 Oktober 2024

GE 20P06SAG Bedienungsanleitung

4 Oktober 2024

Haier ES 15V-SD Bedienungsanleitung

4 Oktober 2024