Kenwood TKR-D710 Bedienungsanleitung

Kenwood Nicht kategorisiert TKR-D710

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kenwood TKR-D710 (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

B5A-1121-00 (K)

TKR-D710

VHF DIGITAL REPEATER

UHF DIGITAL REPEATER

INSTRUCTION MANUAL

RELAIS NUMÉRIQUE VHF

RELAIS NUMÉRIQUE UHF

MODE D’EMPLOI

REPETIDOR DIGITAL VHF

REPETIDOR DIGITAL UHF

MANUAL DE INSTRUCCIONES

TKR-D810

◆ Do not install the repeater in explosive atmospheres (inﬂ ammable

gas, dust particles, metallic powders, grain powders, etc.).

◆ This repeater is intended for use as a ﬁ xed base station with

the antenna located outdoors on the rooftop or on an antenna

tower.

◆ This repeater is designed for a 13.6 V DC power source!

Never use a 24 V DC or higher source to power the repeater.

◆ Use only the supplied DC cord.

◆ Do not remove the ferrite core attached to the DC cord. Doing

so may cause interference with radio communications.

THANK YOU!

We are grateful you purchased this repeater. We KENWOOD

believe this easy-to-program repeater will be highly eﬀ ective in

your communications system, and will keep personnel operating

at peak eﬃ ciency.

PRECAUTIONS

• Do not expose the unit to rain or moisture; to prevent ﬁ re or

electric shock.

• Do not open the unit under any circumstances; to avoid risk of

electric shock.

• Do not expose the unit to long periods of direct sunlight, nor

place it close to heating appliances.

• Do not place the unit in excessively dusty and/or humid areas,

nor on unstable surfaces.

• Do not put the plastic bag used for packing of this equipment

on the place which reaches a small child's hand. It will

become a cause of suffocation if it wears ﬂ atly.

• Always switch the transceiver power off before installing

optional accessories.

• If you detect an abnormal odor or smoke coming from the unit,

disconnect the power from the unit immediately. Contact your

KENWOOD service center or dealer.

NOTICES TO THE USER

UNPACKING AND CHECKING EQUIPMENT

Note: The following unpacking information is for use by your

KENWOOD dealer, an authorized KENWOOD service center, or the

factory.

Carefully unpack the repeater. We recommend that you identify

the items listed in the following table before discarding the packing

material. If any items are missing or have been damaged during

shipment, ﬁ le a claim with the carrier immediately.

Item Part Number Quantity

Hardware ﬁ xture J21-8559-XX 1

Front glass B10-2635-XX 1

Name plates B11-1259-XX 1

Cushion G13-1801-XX 4

Cushion G13-1802-XX 4

Foot J02-0475-XX 2

Foot J02-0492-XX 2

Grommet J59-0302-XX 2

Handle K01-0418-XX 1

Screws N30-4006-XX 2

Screws N35-3006-XX 5

DC cord E30-3427-XX 1

Lead wire with connector (15 pin) E31-3228-XX 1

Fuse F52-0042-XX 1

Instruction Manual B5A-1121-XX 1

INSTALLATION

To install the handles onto the front panel of the repeater, align the

handles with the holes on the front panel, then secure the handles

using the supplied screws.

Please consult your dealer for installing the repeater and antenna.

VHF DIGITAL REPEATER/ UHF DIGITAL REPEATER

INSTRUCTION MANUAL

TKR-D710/ TKR-D810

◆ Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆ Illegal operation is punishable by ﬁ ne and/or imprisonment.

◆ Refer service to qualiﬁ ed technicians only.

One or more of the following statements may be applicable:

FCC WARNING

This equipment generates or uses radio frequency energy. Changes

or modiﬁ cations to this equipment may cause harmful interference

unless the modiﬁ cations are expressly approved by the party

responsible/JVC KENWOOD. The user could lose the authority to

operate this equipment if an unauthorized change or modiﬁ cation is

made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY

THE FCC

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can generate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur

in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer for technical assistance.

Firmware Copyrights

The title to and ownership of copyrights for ﬁ rmware embedded in

KENWOOD product memories are reserved for JVC KENWOOD

Corporation.

The AMBE+2TM voice coding Technology embodied in this product

is protected by intellectual property rights including patent rights,

copyrights and trade secrets of Digital Voice Systems, Inc. This

voice coding Technology is licensed solely for use within this

Communications Equipment. The user of this Technology is

explicitly prohibited from attempting to extract, remove, decompile,

reverse engineer, or disassemble the Object Code, or in any other

way convert the Object Code into a human-readable form. U.S.

Patent Nos. #6,199,037, #6,912,495, #8,200,497, #7,970,606, and

#8,359,197.

REPEATER OPERATION

Note:

◆ Please consult your dealer for programming the repeater.

◆ After switching the power on, the CH/STATUS display blinks for

approximately 30 seconds, until the internal circuit stabilizes. Wait

until the display remains lit, before operating.

When power is applied to the unit, the indicator lights:POWER

・ Green when using the DC jack.

The indicator lights green while receiving a signal and the BUSY

TX indicator lights red while transmitting.

■ Rear Panel

a TX OUT jack

Connect a TX antenna or a duplexer to this receptacle.

b CONTROL I/O jack

Connect a repeater controller or a remote panel to this

DB-25 interface.

c REF IN jack

This jack is currently not used.

d RX IN jack

Connect an RX antenna or a duplexer to this BNC

receptacle.

e FUSE

Insert 15 A blade fuse into this fuse holder.

CONTROLS AND FUNCTIONS

■ Front Panel

f DC 13.6 V jack

Connect a 13.6 V DC power supply to this jack.

g N SYNC 1 / 2 jack

This jack is currently not used. Future functions include

connecting another repeater or optional device.

h TEST/SPKR jack

Test input/output jack. Connect an external speaker to this

jack. When using a Built-in speaker, connect the attached

Lead wire with connector (15 pin) to this jack.

TRANSCEIVER OPERATION (Analog mode only)

■ Receive

Adjust the volume to your desired level. You may need to

readjust the volume if you are having interference while

receiving a message from your dispatcher or another member

in your ﬂ eet.

The BUSY indicator lights green while a signal is being

received.

■ Transmit

1 Listen to the channel before transmitting, to make sure it is

not being used.

2 PTT Press the microphone switch, then speak in your

normal speaking voice.

The indicator lights red while transmitting.TX

3 When you ﬁ nish speaking, release the PTT switch.

Speaker

CH/STATUS Display

Two 7-segment digits display the channel number, name,

or status.

VOLUME control

Rotate to adjust the audio.

POWER switch

POWER indicator

Lights green when power is supplied to the DC 13.6 V jack.

MIC jack

Connect a microphone to this 8-pin modular jack.

Programmable Function keys

Press these keys to activate their programmable functions.

BUSY indicator

Lights green while a signal is being received.

TX indicator

Lights red while transmitting.

a b d e

CH/STATUS

VOLUME

BUSYTX POWER

MIC

a b d e

FUSE

N S Y NC

D C 1 3 . 6V

REF ININ RX 

TX OUT CONTRO L

I / O

TEST/SPKR

Produktspezifikationen

Marke:	Kenwood
Kategorie:	Nicht kategorisiert
Modell:	TKR-D710
Upgradefähige Firmware:	Ja
Breite:	483 mm
Tiefe:	340 mm
Gewicht:	9700 g
Höhe:	88 mm
Eingebautes Display:	Ja
Betriebstemperatur:	-30 - 60 °C
Zertifizierung:	FCC, IC
Anzahl der programmierbaren Tasten:	6
Stromverbrauch (max.):	50 W
Anzahl Kanäle:	30 Kanäle
LED-Anzeigen:	Ja
Eingangsspannung:	13.6 V
Empfangsbereich (VHF):	136 - 174 MHz
Empfangsbereich (UHF):	136 - 174 MHz