Kenwood DNX5120 Bedienungsanleitung
Kenwood
GPS-Gerät
DNX5120
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂźr Kenwood DNX5120 (33 Seiten) in der Kategorie GPS-Gerät. Dieser Bedienungsanleitung war fĂźr 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/33
Š B54-4624-00/00 (KW/K2W)
DNX5120
DNX512EX
GPS NAVIGATION SYSTEM
INSTALLATION MANUAL
SYSTĂME DE NAVIGATION GPS
MANUEL DâINSTALLATION
SISTEMA DE NAVEGACIĂN GPS
MANUAL DE INSTALACIĂN
2 | DNX5120/DNX512EX
Accessories
1
..........1
2
..........1
3
..........2
4
..........1
5
..........1
6
..........6
7
..........6
8
..........1
9
..........1
0
..........1
!
..........1
English | 3
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
2WARNING
⢠If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
Acquiring GPS Signals
The first time you turn on the DNX5120/DNX512EX,
you must wait while the system acquires satellite
signals for the first time. This process could take up to
several minutes. Make sure your vehicle is outdoors
in an open area away from tall buildings and trees for
fastest acquisition. After the system acquires satellites
for the first time, it will acquire satellites quickly each
time thereafter.
¤
⢠Mounting and wiring this product requires skills and
experience. For safetyâs sake, leave the mounting and wiring
work to professionals.
⢠Make sure to ground the unit to a negative 12V DC power
supply.
⢠Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
⢠Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
⢠If the power is not turned ON (âPROTECTâ is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
⢠If your carâs ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
⢠If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
⢠If the fuse blows, first make sure the wires arenât touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
⢠Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
⢠Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
⢠When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the connector to a rear output terminal.-
⢠After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
⢠Mount the unit so that the mounting angle is 30° or less.
⢠This unit has the cooling fan (page 5) to decrease the
internal temperature. Do not mount the unit in a place
where the cooling fan of the unit are blocked. Blocking
these openings will inhibit the cooling of the internal
temperature and result in malfunction.
⢠Do not press hard on the panel surface when installing the
unit to the vehicle. Otherwise scars, damage, or failure may
result.
Produktspezifikationen
| Marke: | Kenwood |
| Kategorie: | GPS-Gerät |
| Modell: | DNX5120 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Kenwood DNX5120 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung GPS-Gerät Kenwood
29 August 2024
6 August 2024
6 August 2024
5 August 2024
4 August 2024
3 August 2024
31 Juli 2024
28 Juli 2024
25 Juli 2024
23 Juli 2024
Bedienungsanleitung GPS-Gerät
- GPS-Gerät Humminbird
- GPS-Gerät Samsung
- GPS-Gerät Acer
- GPS-Gerät Nedis
- GPS-Gerät LG
- GPS-Gerät Maginon
- GPS-Gerät Renkforce
- GPS-Gerät Ventus
- GPS-Gerät Polar
- GPS-Gerät Pioneer
- GPS-Gerät Dual
- GPS-Gerät Hitachi
- GPS-Gerät Garmin
- GPS-Gerät Mio
- GPS-Gerät Bushnell
- GPS-Gerät Fysic
- GPS-Gerät Lowrance
- GPS-Gerät First Alert
- GPS-Gerät Alpine
- GPS-Gerät Uniden
- GPS-Gerät Kogan
- GPS-Gerät Audiovox
- GPS-Gerät Falk
- GPS-Gerät Magellan
- GPS-Gerät Navman
- GPS-Gerät TomTom
- GPS-Gerät Lezyne
- GPS-Gerät IFM
- GPS-Gerät Teltonika
- GPS-Gerät GlobalSat
- GPS-Gerät Nedsoft
- GPS-Gerät Orbit
- GPS-Gerät QStarz
- GPS-Gerät Tile
- GPS-Gerät Wintec
- GPS-Gerät Navilock
- GPS-Gerät Hamlet
- GPS-Gerät Coyote
- GPS-Gerät Canyon
- GPS-Gerät Avidyne
- GPS-Gerät Lantronix
- GPS-Gerät Moki
- GPS-Gerät Chipolo
- GPS-Gerät Spotter
- GPS-Gerät Tractive
- GPS-Gerät Tragant
- GPS-Gerät Trackilive
- GPS-Gerät LifeWatcher
- GPS-Gerät PAJ GPS
- GPS-Gerät Cobblestone
Neueste Bedienungsanleitung fĂźr -Kategorien-
7 Oktober 2024
5 Oktober 2024
4 Oktober 2024
4 Oktober 2024
3 Oktober 2024
23 September 2024
16 September 2024
11 September 2024
9 September 2024
6 September 2024