Kenwood DDX8046BT Bedienungsanleitung

Kenwood GPS-Gerät DDX8046BT

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kenwood DDX8046BT (32 Seiten) in der Kategorie GPS-Gerät. Dieser Bedienungsanleitung war für 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/32
GPS NAVIGATION SYSTEM
SYSTÈME DE NAVIGATION GPS
SISTEMA DE NAVEGACIÓN GPS
DNX SERIES
DNX9960
MONITOR WITH DVD RECEIVER
MONITEUR AVEC RÉCEPTEUR DVD
MONITOR CON RECEPTOR DVD
DDX SERIES
DDX896 DDX8046BT
INSTALLATION MANUAL
MANUEL D'INSTALLATION
MANUAL DE INSTALACIÓN
Š B54-4774-00/00 (KW/RW)
2 DNX SERIES/ DDX SERIES
Installation Procedure
1
..........1
2
..........1
3
..........1
4
..........1
5
..........2
6
..........1
7
..........1
8
..........6
9
..........6
0
..........1
!
DNX9960 only
..........1
@
DNX9960 only
..........1
#
..........1
$
DNX9960 only
..........1
%
DNX9960 only
..........1
Accessories
1. To prevent a short circuit, remove the key
from the ignition and disconnect the -
battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring
harness.
4. Connect the wiring harness wires in the
following order: ground, battery, ignition.
5. Connect the wiring harness connector to
the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
9. Perform the Initial Setup. (Refer to the
Instruction Manual.)
2WARNING
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
• Do not cut out the fuse from the ignition wire
(red) and the battery wire (yellow). The power
supply must be connected to the wires via the
fuse.
Acquiring GPS Signals
The first time you turn on DNX9960, you
must wait while the system acquires satellite
signals for the first time. This process could
take up to several minutes. Make sure your
vehicle is outdoors in an open area away from
tall buildings and trees for fastest acquisition.
After the system acquires satellites for the
first time, it will acquire satellites quickly each
time thereafter.
About the Front Panel
When removing the product from the
box or installing it, the front panel may be
positioned at the angle shown in (Fig. 1). This
is due to the characteristics of mechanism
the product is equipped with.
When the product is first powered on works
English 3
properly, the front panel will automatically
move into the position (initial setting angle)
shown in (Fig. 2).
(Fig. 1) (Fig. 2)
After the Installation
After the installation, perform the Initial Setup
by referring to the instruction manual.
¤
• Mounting and wiring this product requires
skills and experience. For best safety, leave the
mounting and wiring work to professionals.
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
• If the power is not turned ON (“PROTECT” is
displayed), the speaker wire may have a short-
circuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
• If your car’s ignition does not have an ACC
position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wire to
a power source with a constant voltage supply,
such as with battery wires, the battery may be
drained.
• If the console has a lid, make sure to install the
unit so that the faceplate will not hit the lid when
closing and opening.
• If the fuse blows, first make sure the wires aren’t
touching to cause a short circuit, then replace the
old fuse with one with the same rating.
• Insulate unconnected wires with vinyl tape or
other similar material. To prevent a short circuit,
do not remove the caps on the ends of the
unconnected wires or the terminals.
• Connect the speaker wires correctly to the
terminals to which they correspond. The unit may
be damaged or fail to work if you share the -
wires or ground them to any metal part in the car.
• When only two speakers are being connected
to the system, connect the connectors either to
both the front output terminals or to both the
rear output terminals (do not mix front and rear).
For example, if you connect the + connector
of the left speaker to a front output terminal, do
not connect the connector to a rear output -
terminal.
• After the unit is installed, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
• Mount the unit so that the mounting angle is 30°
or less.
• This unit has the cooling fan (page 5) to decrease
the internal temperature. Do not mount the unit
in a place where the cooling fan of the unit are
blocked. Blocking these openings will inhibit the
cooling of the internal temperature and result in
malfunction.
• Do not press hard on the panel surface when
installing the unit to the vehicle. Otherwise scars,
damage, or failure may result.
• Reception may drop if there are metal objects
near the Bluetooth antenna.
Bluetooth antenna unit
¤ CAUTION
Install this unit in the console of your
vehicle.
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.


Produktspezifikationen

Marke: Kenwood
Kategorie: GPS-Gerät
Modell: DDX8046BT

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kenwood DDX8046BT benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung GPS-Gerät Kenwood

Bedienungsanleitung GPS-Gerät

Neueste Bedienungsanleitung fĂźr -Kategorien-