Kenwood CMOS 210 Bedienungsanleitung
Kenwood
Rückfahrkamera
CMOS 210
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kenwood CMOS 210 (116 Seiten) in der Kategorie Rückfahrkamera. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/116
CMOS-310
CMOS-210
UNIVERSAL MULTI-VIEW CAMERA/ UNIVERSAL REAR VIEW CAMERA
INSTRUCTION MANUAL
CAMÉRA MULTI-VUES UNIVERSELLE/ CAMÉRA DE RECUL UNIVERSELLE
MODE D’EMPLOI
UNIVERSAL MULTIVIEW-KAMERA/ UNIVERSAL RÜCKFAHRKAMERA
BEDIENUNGSANLEITUNG
UNIVERSELE MULTIVIEWCAMERA/ UNIVERSELE ACHTERUITRIJCAMERA
GEBRUIKSAANWIJZING
TELECAMERA MULTIVISIONE UNIVERSALE/ TELECAMERA PER RETROMARCIA UNIVERSALE
ISTRUZIONI PER L’USO
CÁMARA DE MULTIVISIÓN UNIVERSAL/ CÁMARA DE VISTA TRASERA UNIVERSAL
MANUAL DE INSTRUCCIONES
CÂMARA MULTIVISÃO UNIVERSAL/ CÂMARA TRASEIRA UNIVERSAL
MANUAL DE INSTRUÇÕES
通用多图像摄像头/通用后视摄像头
使用说明书
B64-4963-08/00 (W)
© 2011 JVC KENWOOD Corporation
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best
performance from your new Universal Camera.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty
card, and in the space provided below. Refer to the model and serial numbers whenever you call
upon your Kenwood dealer for information or service on the product.
Model CMOS-310/CMOS-210 Serial number
US Residence Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
2 | CMOS-310/CMOS-210
• When mounting this unit, make sure none of the leads are
trapped between this unit and the surrounding metalwork
or ttings.
• Do not mount this unit near the heater outlet, where
it would be a ected by heat, or near the doors, where
rainwater might splash onto it. (Never install in locations
such as the above because of the danger of malfunction
due to high temperatures.)
• Before drilling any mounting holes always check behind
where you want to drill the holes. Do not drill into the gas
line, brake line, electrical wiring or other important parts.
• If this unit is installed in the passenger compartment,
anchor it securely so it does not break free while the car is
moving, and cause injury or an accident.
• If this unit is installed under a front seat, make sure it does
not obstruct seat movement. Route all leads and cords
carefully around the sliding mechanism so they do not get
caught or pinched in the mechanism and cause a short
circuit.
Care and maintenance
• When the product gets dirty, wipe dry with a silicon cloth
or soft cloth. If it is seriously stained, remove stain with
a cloth moistened with a neutral cleaner and then wipe
the cleaner away. Do not use a hard cloth and/or a volatile
substance such as lacquer thinner or alcohol, scratches,
deformation, degradation and/or damage may result.
• When a lens component gets dirty, wipe gently with a soft
cloth moistened with water. Do not rub with a dry cloth to
prevent scratching the lens.
Installation Procedure
1 To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2 Make the proper input and output wire connections
for each unit.
3 Connect the wiring harness wires in the following
order: ground, ignition and camera unit.
4 Install the unit in your car.
5 Reconnect the - battery.
WARNING
• If you connect the ignition wire (Red) to the car chassis
(Ground), you may cause a short circuit, that in turn may
start a re. Always connect those wires to the power source
running through the fuse box.
• Do not cut out the fuse from the ignition wire (Red). The
power supply must be connected to the wires via the fuse.
WARNING
To prevent injury or fire, take the following
precautions:
• To prevent a short circuit, never put or leave any metallic
objects (such as coins or metal tools) inside the unit.
• Installation and wiring of this product require specialist
skill and experience. To assure your safety, please request a
specialist technician to install the unit.
CAUTION
To prevent damage to the product, take the
following precautions:
• Make sure to ground the unit to a negative 12V DC power
supply.
• When replacing a fuse, only use a new fuse with the
prescribed rating. Using a fuse with the wrong rating may
cause your unit to malfunction.
• Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
NOTE
• This product is a rear view camera for checking the view at
the rear of a car.
• A rear view camera is a camera that provides symmetrical
images in the same way as rear and side view mirrors.
• Connection to a TV with an RCA video input is possible,
but con rm whether the TV you use has a reverse gear
connection function.
• This product is designed to supplement the driver’s rear
view, but the camera images do not show all dangers and
obstacles. Be sure to look behind you when reversing to
con rm the view.
• This product features a wide-angle lens, so the near view
is wide and the far view is narrow, which may create a
false sense of distance. Be sure to look behind you when
reversing to con rm the view.
• Do not wash your car with an automatic car wash or
high-pressure water as it may result in water entering the
camera or the camera falling o .
• Check camera bracket installation before driving.
Are the screws loose?
- Is the camera bracket rmly secured?
- If the rear view camera comes loose while you are driving
it may cause an accident.
• Before nally installing the unit, connect the wiring
temporarily, making sure it is all connected up properly,
and the unit and the system work.
Before Use/ Installation Procedure
CMOS-310/CMOS-210 | 3
ENGLISH
• Lay the cords by avoiding high-temperature areas. Use
corrugated tubes for wiring inside the engine room. If a
cord contacts a high-temperature area of the vehicle, the
coating may melt and cause short-circuiting, which may
lead to a re or electric shock hazard.
Accessories
CAUTION
• If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and o with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
• If the fuse blows, rst make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
• Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Install so that it does not obstruct the rear eld of view.
• Install so that it does not protrude from the side of the car.
• Do not perform installation in rain or fog.
• When humidity is high, dry the surface to which the unit is
to be attached before installing.
• Moisture on the attachment surface reduces adhesive
strength, which may lead to the unit coming o .
• Do not attach the camera bracket to areas on the car body
treated with uorocarbon resin, or glass.
• May result in the rear view camera falling o .
- Do not apply water to the unit.
- Do not expose the unit to rain.
- Do not subject the camera to unnecessary force.
- Thoroughly clean where tape is used for sticking on the
unit.
• Refer to the Instruction’s manual for details on connecting
the other units, then make connections correctly.
• Secure the wiring with cable clamps or adhesive tape.
To protect the wiring, wrap adhesive tape around them
where they lie against metal parts.
• Route and secure all wiring so it cannot touch any moving
parts, such as the gear shift, handbrake and seat rails.
• Do not route wiring in places that get hot, such as near the
heater outlet. If the insulation of the wiring melts or gets
torn, there is a danger of the wiring short-circuiting to the
vehicle body.
• When replacing the fuse, be sure to use only fuse of the
rating prescribed on the fuse holder.
• To minimize noise locate the TV antenna cable, radio
antenna cable and RCA cable as far away from each other
as possible.
• Do not install the power supply box unit in places where
it may become subject to high temperatures or humidity,
such as:
- Places close to a heater, vent or air conditioner.
- Places exposed to direct sunlight, such as on top of the
dashboard or the rear shelf.
- Places that may be splashed by rain, for example close to
the door.
Waterproof packing ..........1
Camera bracket clamping screw..........1
Camera (with camera bracket) ..........1
Switch unit..........1
Double-side adhesive tape ..........1
CMOS-310 only
Power cord ..........1
CMOS-310 CMOS-210
Produktspezifikationen
| Marke: | Kenwood |
| Kategorie: | Rückfahrkamera |
| Modell: | CMOS 210 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Kenwood CMOS 210 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Rückfahrkamera Kenwood
25 August 2024
28 Juni 2024
18 Februar 2024
Bedienungsanleitung Rückfahrkamera
- Rückfahrkamera AEG
- Rückfahrkamera Conrad
- Rückfahrkamera MarQuant
- Rückfahrkamera Trebs
- Rückfahrkamera Dometic
- Rückfahrkamera Pyle
- Rückfahrkamera Pioneer
- Rückfahrkamera Garmin
- Rückfahrkamera Waeco
- Rückfahrkamera XOMAX
- Rückfahrkamera Beeper
- Rückfahrkamera Alpine
- Rückfahrkamera Pro User
- Rückfahrkamera XZENT
- Rückfahrkamera Clarion
- Rückfahrkamera Audiovox
- Rückfahrkamera DNT
- Rückfahrkamera Tracer
- Rückfahrkamera Furrion
- Rückfahrkamera Luis
- Rückfahrkamera Mobiset
- Rückfahrkamera VDO Dayton
- Rückfahrkamera Veise
- Rückfahrkamera CRUX
- Rückfahrkamera Valueline
- Rückfahrkamera Camos
- Rückfahrkamera CARMATRIX
- Rückfahrkamera Boyo
- Rückfahrkamera AutoXtreme
Neueste Bedienungsanleitung für -Kategorien-
19 September 2024
7 September 2024
7 September 2024
7 September 2024
7 September 2024
5 September 2024
3 September 2024
2 September 2024
2 September 2024
2 September 2024