Kenwood CA-CUT14 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kenwood CA-CUT14 (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new product.
© 2023 JVCKENWOOD Corporation
CA-CUT14
CUT-IN LID KIT FOR 6” X 9 SPEAKERS DESIGNED AND ENGINEERED
FOR 2014-UP HARLEY-DAVIDSON® RUSHMORE MOTORCYCLES WITH
FACTORY-STYLE HARD SADDLEBAGS
INSTRUCTION MANUAL
JVCKENWOOD Corporation
Figure 1.1
Safety precautions
WARNING
Contents
Section 1: Getting Started.......................................................2
Section 2: Disassembling The Factory Lid............................3
Section 3: Mounting The Templates......................................4
Section 4: Wiring The Saddlebags For Speakers.................7
Section 5: Wiring From Amplifier To Saddlebags...............7
The factory saddlebag hinges limit the size of the speaker magnet that can be
used and allow the lids to open and close without issue. KENWOOD assumes
ZERO RESPONSIBILITY for tment issues, or water leaks when any speaker
brand other than KENWOOD is used.
Do Not Use “Thread Lock” or “Screw Glue” of any kind, as it destroys plastic and
will cause part failure.
Most speaker magnets are large and powerful. Credit cards and electronics
can be sensitive to magnets, so please exercise caution in how you pack your
saddlebags. Metal objects packed into your bags may end up stuck to the
magnet, so please use caution when opening the lids. Magnets can also get
hot when speakers are being played, especially at higher volumes. Please
consider this when packing your saddlebags.
2
Section 1 - Getting Started
Installation procedure
1. Remove the saddlebag from the bike and put it on a stable working surface (placing
blankets, towels, etc. on your work surface will help to protect the paint).
2. The black circle in Fig 1.1 is where a 5/8”
(16mm) hole will need to be drilled. This
hole is where the supplied silicone grommet
will go to allow the lid’s speaker wire to pass
through from the saddlebag. Use masking
tape over the painted area to be drilled and
start with a small bit, gradually working your
way up to the 5/8” (16mm) hole. Drilling the
hole with the lid still on is recommended.
3. Locate the wire harness and take the 48” section with the silicone grommet in line and
install it into the saddle bag, making sure the 2 speakerspades” are on the inside of the
bag and the single 2-pin connector is on the outside of the bag. The black squares (also in
Fig 1.1) are an approximation of where the supplied zip tie peel and stick anchors will be
placed.
NOTE: Note: Before applying the anchors, you need to clean the plastic WELL using 99%
isopropyl alcohol, or a similar cleaner. DO NOT use Acetone (it will eat plastic). Do not
apply pads until the cleaner has completely evaporated.
3
Section 1 - Getting Started - Cont.
Section 2 - Disassembling The Factory Lid
NOTE: The kit comes with 2 types of screws:
6 (each) Phillips head screws with a pointy end
16 (each) Phillips Thread Forming screws with a “at end
For proper installation of this kit, you will need to use the correct screws throughout the
process. As you disassemble your factory lid, please make note of what screws came from
where, as they will be re-used.
1. Referencing Fig. 1.2, open the factory lid and you will see 2 T15” Torx screws on the
“bag side” of the cloth tether that holds the lid to the bag. Remove these 2 screws, move
the cloth tether out of the way, and you will see 2 more of the same screws which also
need to be removed. The lid is now free from the bag.
GASKET SEAM
STARTS HERE
4 MAIN SCREWS
FACTORY
LATCHING
MECHANISM
(SHOWN ON WHITE
LID FOR CONTRAST)
Figure 1.2


Produktspezifikationen

Marke: Kenwood
Kategorie: Nicht kategorisiert
Modell: CA-CUT14

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kenwood CA-CUT14 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Kenwood

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-