Kanto YU Passive Bedienungsanleitung

Kanto Lautsprecher YU Passive

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kanto YU Passive (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Supporting your digital lifestyle
English
User Manual
YU Passive Speakers
Thank you for choosing YU Passive speakers, designed by Kanto in Canada. We recommend you
read these instructions carefully before using the speakers, and keep them for future reference.
Kanto cannot be liable for damage or injury caused by incorrect setup or use of this product.
These speakers were carefully tested and inspected during production, and before packaging
and shipping. After unpacking, please check for any damage. It is rare that a unit is damaged
during shipping, but if this happens contact your retailer immediately. You can also call Kanto
directly at 1-888-848-2643 or email support@kantoliving.com.
Introduction
What's in the Box?
YU Passive
Speakers
User
Manual
x8
Self-Adhesive
Rubber Feet
x2
2
We recommend the Kanto SP26PL and SP32PL oor stands for both the YU Passive 4" and YU Passive
5.25". For desktop use, we recommend the S4 and SP9 desktop stands for YU Passive 4", and the S6 and
SP6HD desktop stands for YU Passive 5.25".
The space between the two speakers and the distance from the listener is important. If the speakers are
positioned too close or too far apart, stereo imaging will not be fully developed.
YU Passive is designed to perform optimally positioned at least 8” from the rear wall in an average
listening room. However, it may not be possible to install the speakers in this position and since rooms
vary in shape, size, and furnishing, a certain amount of experimentation is necessary to determine the
most suitable position.
Moving the speakers very close to the rear wall will enhance the bass frequencies but will tend to reduce
soundstage depth, while moving the speakers away from the rear wall will tend to have the opposite
eect. Avoid positioning the speakers close to or in the corners of the room, as this will excite undesirable
room coupling in the low and middle frequencies. If the width of the rear wall is limited then toe-in the
speakers slightly to reduce reections. Room characteristics and positioning have a profound eect on
the performance of the speakers, so time and eort devoted to achieving the optimum positions will be
rewarded.
Setting Up Your Speakers
YU Passive 4" is rated to 70 W at 4 ohms, YU Passive 5.25" is rated to 100 W at 6 ohms.
Repeat the above procedure for connecting the remaining speaker to the RIGHT amplier channel. Make
sure that no bare wires from any of the connections touch other teminals as this could cause a short and
damage your equipment.
Conventional Connection
Amplier Requirements
Using 16-12 gauge speaker wire, connect the RED "positive" (+) terminal of one speaker to the RED
"positive" (+) terminal of your amplier's LEFT channel. Connect the BLACK "negative" (-) terminal of the
speaker to the BLACK "negative" (-) teminal of your amplier's LEFT channel.
Attention
When connecting audio cables the amplier must be turned OFF. After connecting all cables, the unit can be turned . ON
5.25”
YUP 6
100 W
6 Ω
4”
YUP4
70 W
4 Ω
3
Specications
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
Important Safety Precautions
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE BACK
PANEL. NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Read these instructions.
Follow all instructions.
Keep these instructions.
Clean only with a dry cloth.
Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including
ampliers) that produce heat.
Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been
damaged in any way, such as liquid has been spilled or objects have fallen into the aparatus, the aparatus
has been exposed to rain or moisture, the apparatus does not operate normally, or the aparatus has been
dropped.
Tweeters 1 inch Silk Dome
Woofers 4 inch Kevlar®
Power Handling 70 W Per Speaker
Impedance 4 ohm
Sensitivity 86 db (2.83 V/1m)
Frequency Response 60 Hz - 20 kHz
Speaker Terminals Knurled Binding Post
Bottom Mounting Hole 1/4"-20
Dimensions
Dimensions (each speaker) 5.5” W x 7.5” D x 8.7” H
(14 x 19 x 22 cm)
Net Weight (each speaker ) 5.5 lb (2.5 kg)
Gross Weight (boxed pair) 14.6 lb (6.6 kg)
Shipping Box Dimensions 11.3” W x 16.7” D x 13.2” H
(28.7 x 42.5 x 33.5 cm)
YU Passive 4"
Tweeters 1 inch Silk Dome
Woofers 5.25 inch Kevlar®
Power Handling 100 W Per Speaker
Impedance 6 ohm
Sensitivity 89 db (2.83 V/1m)
Frequency Response 50 Hz - 20 kHz
Speaker Terminals Knurled Binding Post
Bottom Mounting Hole 1/4"-20
Dimensions
Dimensions (each speaker) 6.9” W x 8.1” D x 10.7” H
(17.5 x 20.5 x 27.2 cm)
Net Weight (each speaker ) 8.7 lb (4 kg)
Gross Weight (boxed pair) 22 lb (10 kg)
Shipping Box Dimensions 12” W x 19.5” D x 15.4” H
(30.5 x 49.5 x 39 cm)
YU Passive 5.25"


Produktspezifikationen

Marke: Kanto
Kategorie: Lautsprecher
Modell: YU Passive

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kanto YU Passive benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Lautsprecher Kanto

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-