JUNG FTRSL231 Bedienungsanleitung
JUNG
Thermostaat
FTRSL231
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JUNG FTRSL231 (6 Seiten) in der Kategorie Thermostaat. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/6
Temperature Management Floor heating controller
Ref.-no.: FTR..231 ..
Operating Instructions
Floor heating controller
1. Area of application
Used in domestic electrical installations to regulate electrical floor heating
systems and temperature control systems.
2. Function
The floor heating controller consists of two parts:
• Control unit for setting the required floor temperature
• Remote sensor in the floor for monitoring the set temperature
Control unit:
Using the setting knob, set the required temperature for your floor. The
numbers 7 – 6 on the knob correspond to a temperature range of
10 – 50 °C.
Note the setting instructions from the manufacturer of your floor heating
system.
If the temperature in the floor falls below the temperature you have set,
the control unit requests heat; this state is displayed by the red LED
above the setting knob. You can therefore see if your heating is using
energy.
A range restriction can also be carried out in the setting knob.
The operating state of your floor heating is switched on or off with the
mains switch 0 – I.
You also have the option of programming a temperature reduction via an
external time switch e.g. during the night.
If you have installed this type of time switch, the temperature reduction is
indicated by the green LED above the setting knob. The temperature
reduction is approx. 5 °C.
Example: The temperature set by you on the control unit is 34 °C
(number on dial = 4). This means that the temperature in the floor e.g.
during the night can drop down to 29 °C without your heating switching
itself on.
Stand: Jun-09 240 9090 1
Temperature Management Floor heating controller
Ref.-no.: FTR..231 ..
Sensor:
The sensor is to be installed in the floor. It monitors the floor temperature
set on the control unit and issues commands to switch the floor heating
on and off.
Safety instructions
Electrical equipment may only be installed and fitted by qualified
electricians while observing the current accident prevention
regulations.
Non-observance of the safety warnings or installation instructions
may damage the device, cause fire or other hazards.
In the event of a fault, mains potential can be present at the sensor.
L The switch 0 – I on the control unit causes a singlepole disconnection
of the device from the mains and interrupts the circuit to the heating
resistor in the floor.
L When working on the load circuit, the mains voltage must be
disconnected in principle.
L When the sensor is interrupted, the relay contact is closed. If the
sensor experiences a short circuit, the relay contact is open.
3. Connection and installation
Control unit
Mount the control unit in a switch box in accordance with
DIN 49 073.
Notice! The device must always be mounted with its supporting
frame on top of the wallpaper!
• Carry out the electrical connection according to the wiring diagram
(Fig. (1)). Solid conductor cross-section: 1 to 2.5 mm2 No PE
conductor required. PE conductor is only used for looping through.
Protection class II can be achieved through appropriate installation
measures.
Abb.1
Symbols used in the wiring diagram
L : L conductor
2
Temperature Management Floor heating controller
Ref.-no.: FTR..231 ..
N : N conductor
TA : Connection for clock signal for temperature reduction
: Load connection
NTC : Connection for remote sensor
• Mount the control unit with the screws supplied.
• Place the center plate together with the frame on the flush insert.
The center plate must snap in place in the top left of the housing
base.
• Tighten the screw (A in Fig. (2)).
• Clip on the setting knob (B).
Abb.2
4. Sensor
The sensor must be laid in a conduit. It is thereby protected against damp
and can easily be replaced in the event of a repair.
Dimension drawing of remote sensor: Fig. (3).
5. Restricting the temperature setting range
The controller is set ex works to the maximum setting range of to 6.
There are 2 adjustment rings (Fig. (4)) in the setting knob which have a
setting range of 5 to 30 °C. When restricting the range, we ask you to
carry out the setting according to the diagram (Fig. (5)):
3
Produktspezifikationen
Marke: | JUNG |
Kategorie: | Thermostaat |
Modell: | FTRSL231 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit JUNG FTRSL231 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Thermostaat JUNG
24 August 2024
8 August 2024
5 August 2024
4 August 2024
3 August 2024
1 August 2024
31 Juli 2024
29 Juli 2024
29 Juli 2024
28 Juli 2024
Bedienungsanleitung Thermostaat
- Thermostaat Basetech
- Thermostaat SilverCrest
- Thermostaat Cotech
- Thermostaat Bosch
- Thermostaat AEG
- Thermostaat Siemens
- Thermostaat ATAG
- Thermostaat EMOS
- Thermostaat Gira
- Thermostaat HomeMatic
- Thermostaat Renkforce
- Thermostaat Schneider
- Thermostaat GE
- Thermostaat King
- Thermostaat Avidsen
- Thermostaat Elro
- Thermostaat Tesla
- Thermostaat Max
- Thermostaat Vaillant
- Thermostaat Honeywell
- Thermostaat Remko
- Thermostaat Junkers
- Thermostaat De Dietrich
- Thermostaat Netatmo
- Thermostaat Theben
- Thermostaat Tado
- Thermostaat Remeha
- Thermostaat Saunier Duval
- Thermostaat Truma
- Thermostaat Viessmann
- Thermostaat Xavax
- Thermostaat Hager
- Thermostaat Dimplex
- Thermostaat Buderus
- Thermostaat Hunter
- Thermostaat Wolf
- Thermostaat Nest
- Thermostaat Magnum
- Thermostaat HQ
- Thermostaat Itho Daalderop
- Thermostaat Carrier
- Thermostaat Tylö
- Thermostaat Busch-Jaeger
- Thermostaat Sygonix
- Thermostaat Orbis
- Thermostaat Econo-heat
- Thermostaat EQ-3
- Thermostaat Eberle
- Thermostaat Bulex
- Thermostaat Danfoss
- Thermostaat Delta Dore
- Thermostaat Fantini Cosmi
- Thermostaat Grässlin
- Thermostaat Oventrop
- Thermostaat Salus
- Thermostaat Seitron
- Thermostaat Elektrobock
- Thermostaat Mikoterm
- Thermostaat Ferroli
- Thermostaat Daikin
- Thermostaat Vemer
- Thermostaat EnerGenie
- Thermostaat Oregon Scientific
- Thermostaat Finder
- Thermostaat Homematic IP
- Thermostaat EQ3
- Thermostaat Elgato
- Thermostaat Elco
- Thermostaat Drayton
- Thermostaat Drayton Erie
- Thermostaat EasyTemp
- Thermostaat Eliwell
- Thermostaat Emerson
- Thermostaat Emmeti
- Thermostaat Enda
- Thermostaat Eneco
- Thermostaat Eqiva
- Thermostaat Essent
- Thermostaat Eurotronic
- Thermostaat Extraflame
- Thermostaat Frico
- Thermostaat Helios (Amfra)
- Thermostaat Hornbach
- Thermostaat Hugo Muller
- Thermostaat ICY
- Thermostaat IR-V
- Thermostaat Itho
- Thermostaat Johnson Control
- Thermostaat Niko
- Thermostaat Nobo
- Thermostaat Otio
- Thermostaat Plieger
- Thermostaat Plugwise
- Thermostaat Radson
- Thermostaat THERMAFLEX
- Thermostaat Thermy
- Thermostaat Hive
- Thermostaat UPM
- Thermostaat VDH
- Thermostaat Watts
- Thermostaat Worcester-Bosch
- Thermostaat Heatit
- Thermostaat POER
- Thermostaat H-Tronic
- Thermostaat PECO
- Thermostaat Emko
- Thermostaat Fibaro
- Thermostaat Heatmiser
- Thermostaat Crestron
- Thermostaat ORNO
- Thermostaat Optima
- Thermostaat HomePilot
- Thermostaat Ouellet
- Thermostaat Maico
- Thermostaat Tellur
- Thermostaat STI
- Thermostaat Tru Components
- Thermostaat Qubino
- Thermostaat Amfra
- Thermostaat Aube
- Thermostaat AWB
- Thermostaat Wattio
- Thermostaat Brink
- Thermostaat 2Heat
- Thermostaat Bryant
- Thermostaat Veria
- Thermostaat Innogy
- Thermostaat ELKO
- Thermostaat MundoControl
- Thermostaat Bearware
- Thermostaat GENERAL Life
Neueste Bedienungsanleitung für -Kategorien-
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
15 September 2024
13 September 2024
13 September 2024
13 September 2024