JUNG ENOAL2995P01-L Bedienungsanleitung

JUNG Nicht kategorisiert ENOAL2995P01-L

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JUNG ENOAL2995P01-L (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 33 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
EnOcean radio transmitter
05.03.20211 / 50024000901
EnOcean radio transmitter
Ref.-no.: ENO A 590 .., ENO LS 990 ..
ENO A 595 .., ENO LS 995 ..
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, îš¿re or property damage possible. Please read and follow manual fully.
The radio communication takes place via a non-exclusively available transmission path, and is therefore not
suitable for safety-related applications, such as emergency stop and emergency call.
These instructions are an integral part of the product and must remain with the end customer.
2 Device components
Fig. 1: Device components
(1) Adhesive pad
(2) Holder plate
(3) Frames (not included in delivery)
(4) Radio module
(5) Rockers
(6) Retaining screw
Fig. 2 and îš¿g. 3: Transport lock and protective îš¿lm
(7) Transport lock for rockers
(8) Protective îš¿lm for holder plate
1
6
23
4
5
8
7
GB
EnOcean radio transmitter
05.03.20212 / 50024000901
3 Function
Intended use
- Radio transmitter for the transmission of switching, dimming or shutter commands to radio receivers of the
EnOcean radio system
- Mounting on appliance box according to DIN 49073, screw îš¿xing on walls or adhesive îš¿xing on smooth, even
surfaces (glass). Adhesive pad included.
Product characteristics
- Battery-free device without external power supply
- Transmitting energy is generated from mechanical energy of actuation (energy harvesting)
- Conîš¿guration interface: NFC Forum Type 2 Tag (ISO/IEC 14443 Part 2 + 3)
- Optional: Encrypted transmission with AES-128 and sequence counter
4 Information for electrically skilled persons
Installation and electrical connection
DANGER
Electrical shock on contact with live parts in the installation environment.
Electrical shocks can be fatal.
Before working on the device, disconnect the power and cover live parts in the area!
Installation location
The radio range in buildings is approx. 30 m without wall penetration.
A wall penetration is not recommended, because it attenuates the radio signal too much.
Fig. 4: Installation location
In that case, the receiver may not be able to receive the signal from the transmitter correctly
Metal parts at the installation site (e.g. metal door frames) or moisture (e.g. in outdoor areas) can also have a
negative e󰀨ect on the radio transmission.
Fitting the device
• Fix holder plate (2) with adhesive pad (1) at the installation location. (see section „Adhesive xing“)
Alternatively, screw the holder plate onto an appliance box or directly onto the wall.
Note marking „Top“.
• Push frame (3) onto holder plate.
• Snap radio module (4) onto holder plate.
arrow on sticker (rear side of radio module) points upwards (or „O“ is up and „I“ is down).
• Optional: Secure the radio module with the enclosed screw (6).
• Snap on rockers (5).
Note marking „Top“.
The transport lock (7) behind the rockers must be removed beforehand. (îš¿g. 2)
EnOcean radio transmitter
05.03.20213 / 50024000901
Adhesive îš¿xing
Important:
The îš¿nal strength of the adhesive is only reached after 24 hours.
• After gluing the holder plate, let the adhesive cure a little.
Important:
The installation location cannot be changed after the adhesive îš¿xing.
• To test the range, carry out commissioning before adhesive xing.
Prerequisite:
Surface is dry, clean, stable and even.
Suitable cleaning agents:
water, degreaser, glass cleaner, methylated spirit
Not suitable for cleaning:
Bath or all-purpose cleaner, aggressive detergents
• Remove the protective lm from the back of the adhesive pad (1).
• Stick the adhesive pad aligned on the surface.
Press îš¿rmly for about 10 seconds.
• Remove the protective lm (8) for the holder plate (2).
Do not remove the remaining protective îš¿lms.
• Stick the holder plate onto the adhesive pad.
5 Operation
Fig. 5: Operation
Operating elements
The radio transmitter is operated either via one rocker (2-channel) or via two rockers (4-channel). There are four
push-buttons (9) under the rockers. The push-buttons are grouped into two channels (A and B). A distinction is made
between two states (I and O) for each channel.
The functions of the rockers (switching, push-button, dimming or blind) are not conîš¿gured in the factory settings of the
device.
Factory settings/Reset
Restoring factory settings:
• Remove rockers (5) carefully with a suitable tool (e.g. button lever).
• Press all four push-buttons (9) and press the activation bar (10) simultaneously 7 x.
Factory settings are restored automatically.
The radio transmitter is no longer taught-in.
Rockers are without function.
• Snap rockers on again.
10
9
9
9
9


Produktspezifikationen

Marke: JUNG
Kategorie: Nicht kategorisiert
Modell: ENOAL2995P01-L

Brauchst du Hilfe?

Wenn Sie Hilfe mit JUNG ENOAL2995P01-L benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert JUNG

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-